Auburn Gear Power Wheel Model 6 Manual de serviço - Página 3
Procurar online ou descarregar pdf Manual de serviço para Sistema de microfone Auburn Gear Power Wheel Model 6. Auburn Gear Power Wheel Model 6 4 páginas. Double reduction
wheel drives with bearing
locknut option
Também para Auburn Gear Power Wheel Model 6: Manual de serviço (4 páginas), Manual de serviço (4 páginas), Manual de serviço (4 páginas), Manual de serviço (4 páginas), Manual de serviço (4 páginas), Manual de serviço (4 páginas)
Imprimir página
STEP 12
Assemble the disengage cover (30) with dimpled center protruding out if
wheel is to be used to drive the vehicle. Assemble and torque the two 5/16 -
18 x 3/4 inch bolts (31). Torque bolts to 10 - 20 lb. ft. (13 - 27 Nm).
NOTE: When installing a hydraulic motor to the Power Wheel drive it is necessary to place an "O" ring or gasket (not supplied by Auburn Gear) between the
motor and the planetary drive. "O" ring sizes: SAE A 2-042, SAE B 2-155, SAE C 2-159.
It is recommended that the primary and secondary carrier assemblies (18 & 21) be serviced in their entirety to protect the integrity of the Power Wheel drive.
IMPORTANT: POWER WHEEL PLANETARY DRIVES ARE SHIPPED WITHOUT LUBRICANT AND MUST BE FILLED TO THE PROPER LEVEL PRIOR
TO START UP.
Observe lubrication recommendations given by the original equipment manufacturer. When specific recommendations are not available, use mild extreme
pressure lubricant API-GL-5, No. 80 or 90 when filling the Power Wheel under normal temperature ranges between 0 - 120°F (-18 to 49°C). Power Wheel is to
be half full of oil when unit is mounted level and horizontal. Use drain and fill plugs located in cover and ring gear. Oil is to be changed after first 50 hours of
operation with subsequent changes every 1000 hours or yearly, which ever comes first. If unit is to be operated vertically, if ambient conditions are outside the
specified range, or if the oil temperature exceeds 200°F (93°C) contact Auburn Gear for oil and level recommendations.
CAUTION: The Power Wheel will not normally be damaged by towing; however, the hydraulic drive components may be damaged unless the Power Wheel is
disengaged from the drive motor. Road speeds in excess of 25 MPH should be avoided unless clearly specified to be permissible by the equipment manufac-
turer.
CAUTION: For units equipped with the standard spring disconnect, assemble the disengage cover (30) with the dimpled center protruding inward. For units
equipped with the optional quick disconnect, push in center plunger of disconnect. For units equipped with a cast iron disengage cover. Remove the four
capscrews (31), small cover (30) and sun gear (22). It may be necessary to rock the vehicle to release the load on the sun gear. Turning the sun gear end for
end will disengage it from the planetary gears. Replace the cover. Some oil will be lost but need not be replaced until sun gear is replaced in the driving position.
A protective film is applied to the Power Wheel at the factory to prevent rust during shipment. Additional protection may be required if the Power Wheel is to be
stored for an extended period of time.
Silastic RTV732 sealer and General Electric Silimate RTV No. 1473 or RTV No. 1503 are currently recommended for sealing gasket surfaces. Sealant should
be applied in a continuous bead, which should be centered on the surface to be sealed but should move to the inside of the hole at each bolt hole location. For
service requirements order Auburn Gear part number 604101.
Maximum intermittent output torque ............................................................................................................................................. 100,000 lb. in. (11,300 Nm)
Maximum input speed ....................................................................................................................................................................................... 5,000 RPM
Oil capacity ................................................................................................................................................................................................ 47 oz (1,390 ml)
STEP 13
Invert the Power Wheel assembly and assemble the coupling (1) with
counterbore out to the input shaft (2).
CARRIER ASSEMBLIES
LUBRICATION RECOMMENDATIONS
TOWING VEHICLE
TO DISENGAGE POWER WHEEL
STORAGE
SEALING COMPOUND
SPECIFICATIONS
3