Dan D'Agostino MOMENTUM M400 MxV Manual do Proprietário - Página 3
Procurar online ou descarregar pdf Manual do Proprietário para Amplificador Dan D'Agostino MOMENTUM M400 MxV. Dan D'Agostino MOMENTUM M400 MxV 9 páginas.
Imprimir página
LEGAL NOTIFICATIONS
Dan D'Agostino Master Audio Systems is a registered trademark of Dan D'Agostino Master Audio
Systems. The information in this owner's manual is subject to change without notice. Current
Version 1.0 of this manual was produced by the Dan D'Agostino Master Audio Systems
engineering, sales and marketing departments.
The information in this manual is the sole property of Dan D'Agostino Master Audio Systems.
Any reproduction in whole or part without the expressed written permission of Dan D'Agostino
Master Audio Systems is prohibited. No material herein may be transmitted in any way including
either electronic or mechanical methods for any purpose without expressed written permission of
Dan D'Agostino Master Audio Systems.
CAUTION:
NO USER SERVICEABLE PARTS INSIDE. Do not open the amplifier's chassis or remove
any of its screws. Contact Dan D'Agostino Master Audio Systems or your dealer if you have
service needs.
WARNING:
Do not expose this amplifier to moisture or excessive humidity, and do not use it
outdoors. Fire hazard may result.
The lightning flash with arrowhead, within an equilateral triangle, is intended
to alert the user to the presence of uninsulated "dangerous voltage" within the
product's enclosure that may be of sufficient magnitude to constitute a risk of
electrical shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user
to the presence of important operating maintenance (servicing) instructions in the
literature accompanying the appliance.
PACKAGE CONTENTS
If any of the following items are missing, please contact your dealer:
✔ 1 Momentum M400 MxV or S250 MxV
amplifier encased in protective static
cling vinyl
✔ 1 AC power cord
✔ 1 single-ended (RCA) to balanced (XLR)
adapter connections (1 for M400 MxV,
2 for S250 MxV)
2
✔ 1 owner's manual
✔ 1 warranty card
✔ 1 pair of white lifting gloves
✔ 1 microfiber cleaning cloth
UNPACKING AND INSTALLATION
Unpacking the Momentum MxV amplifier from the Pelican case
Two adults are recommended for lifting the nearly 100-pound amplifier from the Pelican case.
When the amplifier is still in its case, please move it to a location near the place where it will
be installed. Remove all jewelry including watches, rings and belts from your person to avoid
damage to the exterior of the amplifier during the removal and installation. Put on the included
white lifting gloves to avoid leaving fingerprints on the amplifier's chassis.
NOTE: You may see slight blemishes in the machined metal parts of the Momentum amplifier's
chassis. This is a normal and unavoidable artifact of the machining process.
Installation requirements
The surface that will support the Momentum MxV amplifier must be capable of safely supporting
the nearly 100-pound weight of the amplifier.
Adequate ventilation must be provided for the amplifier. There should be at least 3 inches
of clearance on each side of the amplifier and 3 inches of clearance at the top, and the bottom
vents of the amplifier must not be obstructed by thick carpet, dust, etc. We recommend that
the amplifier be installed in an open equipment rack or on an amplifier stand to assure proper
ventilation. The amplifier may be installed in a closed cabinet in an equipment closet, but the
cabinet or closet must be designed with substantial ventilation at top and bottom; active
ventilation (i.e., powered fans) is preferred. Do not place the amplifier directly on a carpeted floor.
For best possible sound quality and maximum output, we recommend you connect the
Momentum MxV amplifier to a dedicated 15-amp or 20-amp outlet.
If you need to return the amplifier for service
If you should need to send the Momentum MxV amplifier back to us for service, be sure to use
the original box and materials for shipment.
Before you ship the amplifier, unplug it from the wall and let it cool down for 6 hours. To protect
the finish during shipping, rewrap the amplifier in the vinyl covering it came in. Make sure the
amp is completely cool and has not been plugged in for 6 hours before you do this. Wrapping
the amplifier when it is warm will cause the vinyl to leech into the amplifier's surface and will
permanently damage the finish.
3