DAN DRYER AE Instruções de instalação - Página 2

Procurar online ou descarregar pdf Instruções de instalação para Secador de cabelo DAN DRYER AE. DAN DRYER AE 2 páginas. Height adjustment glide
Também para DAN DRYER AE: Instruções de instalação (2 páginas)

Imprimir página

INSTALLATION ON CONCRETE OR BRICK WALL:

Attach the template (Fig. 1) to the wall with tape ensuring that it is level.

➊

Mark and drill holes "A". Drill holes to fit plugs for 8 mm screws.

➋

Insert plugs and secure the

➌

dryer to the wall with 8 mm

screws.

INSTALLATION ON WOODEN

OR PLASTER WALL:

Attach the template (Fig. 1) to

➊

the wall with tape ensuring

that it is level.

Mark and drill holes "A".

➋

Secure the dryer with 8 mm

➌

screws for relevant wall type.

Use plugs for plaster walls.

INSTALLATION HEIGHTS:

From floor to the lower edge of the dryer:

mounted as

hand dryer

1150 mm (45")

Adults

950 mm (38")

Children

950 mm (38")

Disabled

If multiple dryers are installed in line, the distance between each dryer must be

minimum 600 mm (24"), measured from the centre of each dryer. Avoid

installation directly above sink, tabletop or other reflective surfaces. If this is

inevitable, it may be necessary to adjust the activation distance.

MAINS CONNECTION:

When connecting directly to the fixed installation wiring via fixed cable or

➊

terminal box in the wall behind the dryer, the cable must be fed through

hole "B" (Fig. 1) in the base plate and connected to the terminal block "E".

Connect by means of three leads of min. 1.5 mm

150 mm long (7 mm of which stripped).

ENG-AA+AE-jord-DK 2019/20.12.2007

Fig. 1

mounted as

hair dryer

1900 mm (75")

1700 mm (67")

1550 mm (61")

cross-section per lead,

If installation as described in point

➋

installation via contact breaker by feeding a loose, insulated cable through

hole "C" at the bottom of the base plate, through tensile relief strap "D" for

connection to terminal block "E". Apply three-core cable with earth wire,

each lead min. 1.5 mm

cross section; maximum cable length: 1.5 m.

Before securing the housing, remove the small relief at the bottom of the

housing with cutting nippers and a file, ensuring that the hole is deburred

and has no sharp edges.

NB: For dryers with stainless steel housings, point

TESTING AND ADJUSTMENT - PUSHBUTTON MODEL:

The adjustable drying time is factory pre-set to approx. 30 seconds. The

adjustment screw in the timer increases the cycle when turned clockwise and

decreases when turned anti-clockwise.

If the dryer is installed as a hair dryer, the drying cycle may be set to the

maximum time - approx. 170 seconds.

Do not attempt to dismantle the magnet attached to the inside end of the

pushbutton - not even to test run the dryer.

TESTING AND ADJUSTMENT – ELECTRONIC MODEL:

The activation distance is factory pre-set to max. 200 mm measured from the

air outlet. The activation distance can be increased by turning the adjusting

screw on the timer clockwise, and decreased by turning the adjusting screw

anti-clockwise.

The dryer starts automatically when hands are placed in the activation area

and stops automatically 4 seconds after hands are removed.

Never test run dryers without the housing being fully secured in its place.

IMPORTANT

•

If the dryer is installed as a hair dryer, it must be mounted out of reach

of persons using shower or bath tub.

•

The dryer must be properly earthed. When connecting directly to the

fixed installation wiring via fixed installation circuit breaker, when

switched off, the total distance of break in the circuit breaker must be

min. 3 mm.

•

Remove the polystyrene protection block located inside the dryer

underneath the motor before switching the dryer on

is not possible, ensure fixed

➊

is the only installation option.

➊