Danfoss 088L5132 Manual do utilizador - Página 2

Procurar online ou descarregar pdf Manual do utilizador para Termostato Danfoss 088L5132. Danfoss 088L5132 20 páginas.
Também para Danfoss 088L5132: Manual de instalação (4 páginas), Manual do utilizador (6 páginas)

Imprimir página

Programmable Thermostats 088L5130/5132

Checking the GFCI

Testing can only be performed while the thermostat is calling for

heat.

Adjust the setpoint until the heating symbol (

Up button to increase the heating demand and then press the OK

button Wait 10 seconds to allow the thermostat to adjust to the

new setpoint.

Then press the TEST button on the top of the thermostat.

The test is successful if the red light in the TEST button lights up

and GROUND FAULT is shown on the display. If this does not oc-

cur, check the installation/contact your electrical installer.

Press the Standby/Reset button to reset the GFCI.

The red light should go out and the display returns to normal ap-

pearance.

Press the Down button to return to the original temperature setting.

If the test fails, check the heating cable and thermostat.

If during normal operation the GFCI trips without the TEST button

being pressed, there could be a ground fault! To check whether it

is a ground fault or nuisance tripping, press Standby/Reset.

If this causes the red light to go off and stay off, it was nuisance

tripping and the system is operating correctly. If this does not oc-

cur, there is a ground fault! Contact your electrical installer.

4-Event Program

I want the temperature to be controlled automati-

cally in accordance with a program of individual

temperature settings for four separate events during

a day:

• when I wake up in the morning,

• when I am away at work,

• when I come home,

• and at night.

To do so, you must perform the following 3 steps:

Step 1: Select automatic temperature control.

Press the OK button to activate the menu.

Press the Up or Down buttons until the Mode option ﬂ ashes.

Press the OK button.

Press the Up or Down buttons until the Auto options ﬂ ashes

in the upper part of the display.

Press the OK button.

Factory setting: Auto mode

AUTO

OVERRIDE

MAN. MODE

MODE

SCHEDULE

PROGRAM

SETTINGS

EXIT

Step 2: Choosing the weekly schedule

for your program.

You have the following options:

5:2 will give you 5 days (Monday to Friday) with the same four

events (Morning, Out, Home, Night) and 2 days (Saturday and

Sunday) with the same two events (Morning and Night).

6:1 will give you 6 days (Monday to Saturday) with the same

four events (Morning, Out, Home, Night) and 1 day (Sunday)

with the same two events (Day and Night).

) appears. Use the

7:0 will give you individual settings for each day from Monday

to Sunday.

Step 3: Select the time and temperature settings for

each event in the program of days selected in the

previous step.

At work

Morning

Please note: The following description illustrates an example in

which settings are made for the daily events in a 5:2 program.

Press the OK button to activate the menu.

Press the Up or Down buttons until the Schedule option ﬂ ashes.

Press the OK button.

Press the Up or Down buttons until the required program (5:2,

6:1 or 7:0) ﬂ ashes in the lower part of the display.

Press the OK button.

SCHEDULE

SET TEMP

PROGRAM

Hour

Minutes

Press the Up or Down buttons until the Program option ﬂ ashes.

Press the OK button.

Press the Up or Down buttons until the day(s) that you wish

to program ﬂ ash in the lower part of the display, e.g. Mon Tue

Wed Thu Fri.

Press the OK button. The symbol for the ﬁ rst event (e.g. morn-

ing) will now ﬂ ash.

Press the OK button. The hour will ﬂ ash, allowing you to set

the hour at which you want the morning period to begin.

Press the Up or Down buttons until the required hour is dis-

played.

Press the OK button. The minutes will ﬂ ash.

Press the Up or Down buttons until the required minutes are

displayed.

English

MON

TUE WED THU

FRI

EXIT

MON

TUE WED THU

FRI

5-day period

At home

Night