Danfoss TS715 Si Instruções de utilização - Página 2
Procurar online ou descarregar pdf Instruções de utilização para Termostato Danfoss TS715 Si. Danfoss TS715 Si 2 páginas. Underfloor heatig timeclock
Também para Danfoss TS715 Si: Instruções de utilização (2 páginas)
Imprimir página
+1HR
ON
12:45
OFF
AUTO
AM
ALL DAY
MO
MAN
PROG
+
SELECT
NEXT ON/OFF
–
Operation
If the colon is blinking the unit is in
automatically switch the underfloor heating on and off at
the times set. However, useful overrides are provided which
enable the user to to make temporary changes to the
times without re-programming the unit.
Manual overrides
When in off,
or
auto
allday
used to switch from off to on for just one hour, or to extend
an existing period by one hour. This will be cancelled by
pressing the
button again, pressing the
+1hr
or when the next on programme is reached.
When in
or
auto
allday
button will switch from on to off, and vice versa. This override
will only last until the next programmed change, when the
automatic programming will resume, or until the button is
pressed again.
When the above overrides are selected a bar appears in the
display against the appropriate legend.
Reset
Should the timeswitch be disconnected from the mains a
small battery symbol will blink on the left of the display. After
the second midnight (between 24 and 48 hours) the display
will go blank and settings will be lost. When mains power is
restored it is recommended that the unit be reset by inserting
a non-metallic object such as a matchstick in the
under the flap. This will restore the factory settings with the
time at 12:00 and Monday (mo) selected. The output will be
off. Note that the colon will be blinking, meaning that the unit
is in
mode and will switch on and off according to the
run
factory programming until reset.
Selecting the operating mode
Behind the flap is the red select button; each press changes the operating
mode as follows:
on
off
auto
DAY
COPY
allday
R/S
mode. It will
run
modes the
button can be
+1hr
button
man
modes pressing the
(manual)
man
r/s
The output is constantly on.
The output is constantly off unless +1hr is pressed.
The output switches on and off to the set programme.
The output switches on at setting 1 and stays on until setting 6.
Choice of 12- or 24-hour clock
At any time whilst in run mode the time displayed can be
toggled between a 12-hour clock with an am/pm indicator
or a 24-hour clock by pressing and holding both day and
on/off
next on/off
G.M.T./B.S.T.
To change from Greenwich Mean Time to British Summer
Time and vice versa while in
the
button to add one hour in Spring, or the
+
put the clock back one hour in Autumn.
Factory pre-set programme
The unit will be pre-set to 7-day/24-hour mode; this can
be altered by moving the pins under the backplate. Firstly
remove the screws under the unit and remove the front face.
There are three operating modes available:
24 hour operation; the same programme
1
each day,
5-day/2-day operation; different
2
programmes for weekdays and weekends,
7-day operation; different programmes for
3
each day.
Set the pins as shown for the operating mode required.
hole
The pre-set factory
the recessed
r/s
matchstick. Please remember that underfloor heating takes
longer to warm up and cool down than conventional radiators
and the heat settings should reflect this. The factory settings
are unlikely to be appropriate.
buttons for 1.5 seconds.
mode: press and hold
run
times can be reinstated by pressing
on/off
button with a non-metallic object such as a
button to
–
1 2 3 4
1 2 3 4
1 2 3 4
7