DANLERS COPIR IP66BK Instruções

Procurar online ou descarregar pdf Instruções para Interruptor DANLERS COPIR IP66BK. DANLERS COPIR IP66BK 2 páginas. Compact person detection switches

Imprimir página

COPIR IP66, COPIR IP66BK

Compact Person Detection Switches

Input: 220-240 Vac 50Hz

PLEASE READ THESE INSTRUCTIONS BEFORE INSTALLING THE PRODUCT

DANLERS COPIR IP66(BK) is IP66 rated and

can be surface mounted onto an external wall.

It incorporates a passive infra-red sensor to

detect movement of a warm body within the

detection zone (diagram 1) and it includes a

photocell to monitor the ambient light level.

The detection range is about 10 metres over

120 degrees, the range reduces to about 8m

at the extremes to prevent nuisance switching.

Product codes:

COPIR IP66: White enclosure (Grey front

facet).

COPIR IP66 BK: Black enclosure.

INSTALLATION PROCEDURE

1. Please read these notes carefully before

commencing work. In case of doubt please

consult a qualifi ed electrician.

2. The detector should be sited so that it is not

shaded from daylight

3. The detector should be mounted between

1 and 2.2 metres high, via any of the four

pre-drilled mounting holes only.

4. It must be mounted with the cable entering

from below.

5. Make sure the power is isolated from the

circuit.

6. The detector should be connected as

shown in diagram overleaf.

L - Live in, N - Neutral in,

SL - Switched Line out.

7. IMPORTANT - Replace terminal cover.

8. Once the wiring has been completed and

verifi ed, switch on the supply and test the

operation.

START UP MODE

When the PIR is powered up, the PIR will

switch on the lighting load for 1 minute then

switch it off. After 2 seconds it will switch

on again if it detects movement. With Time

set to minimum the load will stay on for 10

seconds so the detection range can be

easily assessed. If a manual override-off

switch after the PIR (diagrams 5 & 6, note 1)

it will not enter the start-up mode each time.

LOADING: See overleaf

LUX AND TIME SET UP

On detecting movement, if the ambient light is

dark enough, the COPIR IP66 (BK) will switch

the load on. The ambient threshold can be set

by the user to between approximately 10 and

1000 lux via the internal LUX adjuster (diagrams

2 and 3). The photocell can be disabled via the

internal mode button (see overleaf).

If no more movement is detected within a

pre-selected time, then the PIR switch will

DANLERS Limited, Vincients Road, CHIPPENHAM, Wiltshire, SN14 6NQ, UK.

Telephone: +44 (0)1249 443377 Fax: +44 (0)1249 443388 E-mail: [email protected]

www.danlers.co.uk

Company Registered Number 2570169 VAT Registration Number 543 5491 38

DAT0027 COPIR IP66

turn the load off. This time lag can be set via

the TIME adjuster to 10 seconds, 20 seconds,

40 seconds, 80 seconds, 2 minutes 30

seconds, 5 minutes,10 minutes, 20 minutes

or 40 minutes (diagram 4).

For convenience, ensure that the TIME is set to

minimum when setting up the LUX level. Afterwards

set the TIME to a value suitable for the application.

1. When powered up, (after 1 minute

stabilisation time) turn lux pot (diagram

C) fully clockwise and time pot fully

anticlockwise.

2. Press the MODE button (diagram 2) for

approximately 0.5s. The LED will go green

indicating the LUX cell is active. (Or press

and hold button for approx. 4 seconds – LED

goes RED indicating Lux cell INACTIVE).

Repeating these steps will toggle the

functionality.

3. If lux cell active, vacate area until PIR switch

switches the load off (should be after 10

seconds).

4. With the LUX as desired on working plane

from daylight ONLY (no artifi cial light), wind

the lux pot anticlockwise whilst waving your

hand in front of the PIR cell. When the PIR

switches the load ON, stop turning the pot.

The Lux inhibit level is now set.

5. Turn the PIR time to the desired timeout

(diagram 4). Whenever a person is detected,

the time lag will start again and the load will

stay switched on.

TROUBLESHOOTING

The PIR does not detect:

• Check power supply.

• Is there an obstruction in front of the lens?

• Person is too far from the COPIR IP66

switch, see detection diagram.

• Person is moving unusually slowly (perhaps

when testing).

• To perform detection test - turn the time

spindle to minimum setting (10 seconds),

cover the lens to stop any detection - load

should switch off in 10 seconds unless going

through its START UP MODE (see opposite).

The PIR stops working

• Ensure the unit is mounted correctly so that

no water can enter.

The PIR false triggers

• Detector is exposed to air movement on

breezy days.

DIAGRAM 1 - WALL MOUNTED DETECTION

Dual colour LED:

RED - PIR active,

Photocell inactive

GREEN - PIR and

Photocell override ON

(passive LUX)

Time

Delay

Spindle

DIAGRAM 2 - TIME / LUX ADJUSTERS (INSIDE CASING)

2.5m

80s

Use Mode

40s

10m

Button to

20s

20m

disable LUX

(see diagram

10s

40m

min

max

TIME

DIAGRAM 3 - LUX ADJUSTMENT

Inside

detector

housing

DIAGRAM 4 - ADJUSTING TIME LAG

Terminal cover

(safety cap)

Locate safety cap plastic

pins in the hole 'L' and

second 'N' holes above

the termination screws.

Press firmly to attach.

DIAGRAM 5 - TERMINAL COVER

Recommended mounting

height 1 to 2.2 metres

Strong detection zone (5m)

i.e. person walking

towards detector

Secondary

detection zone

(10m, 8m at

extremes)

i.e. person walking

perpendicular to

detector

Lux Cell

Mode

STATUS

MODE

Lux

Setting

1000

Spindle

TIME

LUX

1000 LUX

10 LUX

max

min

LUX

2.5m

80s

40s

10m

20s

20m

10s

40m

min

max

TIME

30/08/19 (Issue 001)

1000 LUX

max

LUX