AudioSource AMP210VS Manual do Proprietário - Página 3

Procurar online ou descarregar pdf Manual do Proprietário para Amplificador AudioSource AMP210VS. AudioSource AMP210VS 4 páginas.

Imprimir página
AudioSource AMP210VS Manual do Proprietário
2
1
3

FRONT PANEL CONTROLS

1. Power Switch
Switches the AMP210VS on or off.
Clip LEDs
2.
Blinks red during signal clipping. Shows solid red during protect mode.
Check speaker wires for shorts or extreme low impedance (< 4 ohms).
Line 1
Speaker IN
V
Interrupt
R
+
IN
L
R
-
6
Serial Number:
REAR PANEL CONTROLS
6.
Interupting Line Input
This is the secondary input, use MAIN IN for your main input.
INTERRUPTING INPUT can be used if a second source is desired and
takes over when signal is present and has at least a 5mV level.
When there is no signal, or a signal with less than 5mV level, the amp
switches back to MAIN IN after a brief delay.
7.
Speaker Level Input/Speaker Level Input Line Select
Can be used to connect a source with speaker level output instead
of line level outputs. Use the Speaker Level Input Line Select to route
the source to either Main Input or Interrupt Input function.
8.
Main Input/Output
MAIN IN should be used as the "primary" or main input for the amplifier.
Connect your receiver or main source to this input. Use MAIN OUT to pass
MAIN IN signal to another amplifier.
9.
Delay Time
Allows for a 3-15 second delay to be set and accommodate
the source connected to the Interrupting Input.
10.
Bass and Treble Controls
These controls can adjust bass and treble frequencies +/- 12dB at 100Hz
and 10kHz.
11.
Master Level Controls
Provides independent adjustment of Left and Right channel
maximum level.
12. Mode Select Switch
Switches the amplifier from Stereo mode to Bridged mode.
STEREO MODE
If you will be connecting one or two pair of speakers to the amplifier, place
the switch in the "Stereo" position. NOTE: For playing 2 pairs of speakers
(A plus B), make sure each speaker has an impedance of 8 ohms or greater.
BRIDGED MODE
When set to "Bridged" mode, the amplifier is a single channel mono amplifier.
BRIDGED MODE- MONO APPLICATION
For bridged mode, playing Right and Left together as mono output, use a
Y cable adapter to connect Right and Left RCA signal to the Right (Red) input
at MAIN IN. Set the MODE switch to BRIDGED and follow the instructions
for bridged speaker connection in the SPEAKER TERMINALS section of
this manual.
NOTE: The AMP210VS supplies 250W in bridged mode, Please verify that your
speakers are capable of handling such power to avoid possible damage!
13970 SW 72nd Ave, Portland, OR 97223 • 503.914.4688 • www.audiosource.net
Line 2
10
V
Main In
L
+
IN
OUT
Bass
L
Delay
Time
Master Level
-
R
3 Sec 15 Sec
Min Max Min Max
8
7
9
3.
Speaker Selector
Selects speaker zone A or B. For A + B zones push both buttons in.
4.
Balance
Fades speaker output between the Right and Left Channels
5.
Volume
Trims amplifier volume from -12dB to +6dB referenced to the rear panel Level
controls.
CAUTION
AVIS
AVIS: RISQUE DE CHOC ELECTRIQE
RISK OF FIRE OR ELECTRIC SHOCK
NE PAS OUVRIR CE CARTER
Use Class 2 Wiring
DO NOT OPEN
RESERVE AU PERSONNEL AUTORISE
CAUTION
Minimum Impedance:
: TO PREVENT ELECTRICAL SHOCK DO NOT REMOVE
COVER. NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO
QUALIFIED PERSONNEL.
8 ohm Bridged
WARNING
: TO PREVENT ELECTRICAL SHOCK DO NOT REMOVE
4 ohm Stereo
COVER. NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO
QUALIFIED PERSONNEL.
Treble
12V Trigger
Mode
Auto On
+
-
Stereo Bridged
IN
OUT
Trigger Normal
R
L
11
12
13
14
13.
12V Trigger
Allows the AMP210VS to be powered on by other electronics or to power
on other electronics via a 3.5mm mini phone plug cable.
14. Power Mode
Sets the power on option of the AMP210VS. Set it to Normal for manual power
on/off. Set to Auto-On for signal sensing power up. Set to Trigger if the 12V
Trigger input is used.
15.
Speaker Zone A Output
Speaker output terminals for zone A. Minimum impedance: 8 ohm bridged
or 4 ohm stereo.
16.
Speaker Zone B Output
Speaker output terminals for zone B. Minimum impedance: 8 ohm bridged
or 4 ohm stereo.
SPEAKER TERMINALS - STEREO MODE
For stereo output connect the speaker's positive (red) terminal to the amplifier's
positive (red) terminal, and the speaker's negative (black) terminal to the
amplifier's negative (black) terminal for each Right and Left speaker.
SPEAKER TERMINALS - BRIDGED MODE
Place the "MODE" switch in the "BRIDGED" position and use both red
terminals to connect to the speaker. Connect the speaker's positive (red)
terminal to the amplifier's red (+) terminal noted next to the bridging mark, and
the speaker's negative (black) terminal to the amplifier's unmarked positive
(red) terminal.
NOTE: Only one zone (A or B) can be bridged. Do not attempt to bridge both
A and B speaker terminals! This may result in a lower impedance than the
amplifier is designed for and may damage your amplifier. The minimum
impedance for the total load connected in bridged mode is 8 ohms.
NOTE: Use Class 2 wiring for speaker connections.
To wire the output connector: 1. Strip the insulation off each speaker wire
to expose 3/8" (10 mm) of bare conductor. 2. Unscrew the output terminal
binding post several twists, insert each wire into the correct terminal.
3. Tighten binding post by twisting clock-wise until it is firmly clamping the
speaker wire.
Warning: While the amplifier does self-protect under most improper output
conditions, misconfiguration of loudspeaker mode and incorrect connection
of loudspeakers could damage connected loudspeakers and/or amplifier.
Please refer installation to a qualified installation professional, and always
check state and local electrical codes when installing.
AMP210VS
OWNER'S MANUAL
4
15
Speaker A
-
R
+
+
L
-
Custom Manufactured in China
115V~ 60Hz 700W
FUSE:
230V~ 50Hz 700W
FUSE:
Bridge
-
+
-
+
+
L
-
R
Speaker B
16
CAUTION: See User Manual Before
17
Replacing Fuse
5
Figure 1. Front Panel
18
Figure 2. Rear Panel
3