Apollo 33 404 Manuais de instalação

Procurar online ou descarregar pdf Manuais de instalação para Sistema de segurança Apollo 33 404. Apollo 33 404 2 páginas. Sounder beacon base with isolator

Imprimir página

Functional Test Data

The product is controlled by the control panel using the output bits in the communication

protocol.

Protocol bit use:

Output Bit

Function

group mode

1 = off

0 = on

continuous tone

1 = on

0 = off

DIN tone

1 = on

0 = off

Fault Finding

Problem

Possible Cause

No response or missing

Incorrect address setting

Incorrect loop wiring (polarity reversed)

Analogue value 1

Sounder test failed

Analogue value 2

Beacon failed

Analogue value 3

Sounder and beacon failed

Analogue value 4

Incorrect group address or address setting

Product fails to operate

Control panel has incorrect cause and effect programming

Incorrect group address setting

Address & tone

setting

Group address

setting

–

Fig. 2 Sounder Beacon Base with isolator

wiring

Apollo Fire Detectors Limited, 36 Brookside Road, Havant, Hants, PO9 1JR, UK

Tel +44 (0)23 9249 2412 Fax +44 (0)23 9249 2754

Email: techsales@apollo-ﬁ re.co.uk Website: www.apollo-ﬁ re.co.uk

Input Bit

Function

group mode conﬁ rmed

1 = group

0 = individual

continuous tone conﬁ rmed

1 = on

0 = off

DIN tone conﬁ rmed

1 = on

0 = off

Remote LED

–R

Volume control

L1 IN

L1 OUT

–

EARTH

Position of Isolator LED

39214-302/Issue 3

Sounder Beacon Base with Isolator

DIN 33 404 Tone Installation Guide

General

This guide describes the installation of the following sounder

Part number

45681-334

45681-292

45681-293

Connect the products only to control panels using either the XP95 or the Discovery protocol.

The Sounder Beacon Base combines a sounder with a beacon and a detector base in one unit.

The beacon is activated whenever the sounder is active and cannot be controlled separately.

The Sounder Beacon Base with short circuit isolator has a yellow LED which illuminates through

the moulding if a short circuit is detected on the loop wiring (see Fig 2).

Note: The Sounder Beacon Base is not suitable for outdoor use.

Mounting Instructions

The sounders may be secured to a UK or European standard conduit box or surface mounted

(providing there is access through the surface for cabling). If a detector is ﬁ tted, lock it if

required by screwing in the grub screw on the head with a 1.5mm hex driver (part no 29600-

095)

Wiring Details

Note: This product is polarity sensitive (supply reversal protected) and will not function if wired

incorrectly.

Connect the positive XP95/Discovery loop cables to the L2 terminals, the negative loop in to

L1 IN and negative loop out to L1 OUT. (See Fig. 3) Functional earth or screen cables may be

terminated to the EARTH connection. When using the sounder as a stand-alone unit, a cap is

available (red cap part no 45681-293 or white cap part no 45681-292) and is secured with a

1.5mm, AF hexagon socket head screw. A hexagonal driver (part no 29600-095) is available

from Apollo. The isolator LED can be seen through the moulding as shown in Fig 2.

Address Setting

The address of the sounder is set using seven segments of the eight-segment DIL switch. The

eighth seg ment is used to adjust the volume output. Segments 1-7 of the switch are set to "0"

(ON) or "1", using a small screwdriver or similar tool. A complete list of address settings is shown

overleaf. If a detector is to be ﬁ tted, set the address as described on page 3.

FIRE DETECTORS LIMITED

Product Description

Sounder Beacon Base with Isolator DIN Tone

White Cap only

Red Cap only