Apollo 1550ETL Resolução de problemas

Procurar online ou descarregar pdf Resolução de problemas para Abertura de portões Apollo 1550ETL. Apollo 1550ETL 2 páginas.

The Apollo 835/836 board is the standard board in all ETL compliant Apollo Gate Operators.

Single gate systems use the 835 board (distinguished by MASTER and EMERGENCY BYPASS

modular receptacles) and DUAL gate systems use the 836 board (distinguished by MASTER,

SLAVE and EMERGENCY BYPASS receptacles). The 836 board may be used in single gate

applications by simply turning PROGRAM SWITCH #3 to the OFF position and only using the

MASTER receptacle of the board.

Apollo 1550 ETL and 1650 ETL systems incorporate the 816E (8' cord) and 816EX (38' cord)

linear actuators. These linear actuators have a SMART SENSOR inside them that sends

information back to the 835/836 board so that the slow start / slow stop feature may be used

when Program switch #10 is ON. The 416E / 416EX actuators (which do not have the smart

sensor) can also be used with the 835/836 boards - however program switch #10 must be in the

OFF position and the slow start / slow stop feature will no longer be available.

Trouble Shooting the Apollo 1550 ETL and 1650 ETL systems:

1. Check your battery! The battery in your gate operator is the power source for the entire

system. If it is not adequately charged, the system will not operator properly. Test the

battery by checking the voltage with a volt-meter while the battery is under load (gate

operating). For AC charged systems – unplug the battery charger before load testing

battery. Battery voltage should be 11.5 volt DC or higher while the operator is running

(battery under load).

2. Program Switch Settings: At the upper center of the board there are 10 program

switches. These switches enable and disable certain features of the Apollo system.

DEFAULT setting of these switches is as follows: SINGLE GATE – 1,2,3,5,10 ON (all

others OFF) DUAL GATE – 1,2,5,10 ON (all others OFF)

3. LED ENABLE BUTTON: On the right side of the board – half way down is the LED

ENABLE button. Pressing this button once and releasing it "enables" the LEDs on the

board for approximately 15 minutes. When the LEDs are enabled – the "STOP" light

should always be lit on the left side of the board. Other LEDs may be lit as well –

depending on the status of the operator. If the gate(s) are in the OPEN position, the

OPEN limit indicator(s) should be lit. If the gate(s) are CLOSED, the CLOSED limit

indicator(s) should be lit. (The OPEN and CLOSED LEDs should never be on at the

same time) Any LEDs that are lit on the left side of the board or at the lower right corner

of the board (except the STOP LED) indicate a TRIGGER from an accessory device

connected at that location. Devices connected where an LED is lit should be removed

before further testing is done. After the system is made operational – these devices may

be reconnected one at a time. Check for proper system operation after each connection.

4. Current Sensitivity: At the top center of the board is the "Current Sensitivity" adjustment.

It adjusts the amount of force the operator will exert before it senses an obstruction. As

the wheel is turned counter clockwise, the operator will reverse more easily. As the

wheel is turned clockwise, the operator will push harder. Any time the system

"CURRENT SENSES" it will stop and reverse for two (2) seconds. If the system

"CURRENT SENSES" a second time before fully opening or closing – it will again reverse

for two (2)_seconds and then go into a HARD SHUTDOWN (see below). Sensitivity

should be set to a level that is sufficiently strong to open and close the gate in all

conditions – yet still sensitive enough to be safe. A good starting point is the one o'clock

position.

APOLLO 1550/1650 Troubleshooting