Duro Dyne SPOTWELDER STAND Instruções de montagem

Procurar online ou descarregar pdf Instruções de montagem para Sistema de soldadura Duro Dyne SPOTWELDER STAND. Duro Dyne SPOTWELDER STAND 2 páginas.

Since 1952

DURO DYNE SPOTWELDER STAND

Refer to the accompanying parts list and assembly drawing

Loosely attach the Front Panel #1 (the panel with a slot) to the inclined surface of the right

Side Panel #3 using 1/4 - 20 x 5/8'' slotted truss head screws, split lock washers and hex nuts.

Stand the unit up and loosely attach the Left Side Panel #4 to the Front Panel #1 using 1/4

- 20 x 5/8'' slotted truss head screws, split lock washers, and hex nuts.

Loosely attach the Rear Panel #2 to the previously assembled panels using 1/4 - 20 x 5/8''

slotted truss head screws, split lock washers and hex nuts.

Loosely attach the Stand Top #5 to the assembled panels (the slots in the Stand Top should

face toward the back of the assembled panels). Use 1/4 - 20 x 5/8'' slotted truss head screws,

split lock washers, and nuts.

Using a screwdriver and a 7/16" wrench, tighten all the bolts securely.

Loosely attach the Foot Pedal Pivot Brackets #7 (with the 90° bend toward the inside) to the

Rear Panel with 1/4 - 20 x 5/8'' slotted truss head screws, split lock washers and hex nuts.

Slide the Foot Pedal Weldment #6 through the slot in the Front Panel and attach it to the

Foot Pedal Pivot Brackets using a 1/4 - 20 x 3/4'' hex head bolt and nyloc nut. Tighten this

bolt snugly, but not tightly, and then tighten the Foot Pedal Pivot Bracket screws completely.

Slip the Compression Spring #13 loop over the 10-32 Threaded Rod #12 and slip the Thread-

ed Rod through the holes in the front of the Side Panels. Secure the Threaded Rod with #10

split lock washers and 10-32 hex nuts.

Slip the "S" Hook #14 through the forward hole in the Foot Pedal weldment and attach the

"S" Hook to the other end of the Compression Spring.

10. Attach the Pull Down Connecting Bar #8 (with the twisted end toward the top of the stand)

to the Foot Pedal Weldment with a 1/4 - 20 x 1" hex head bolt and nyloc nut. Place a 1/4'' flat

washer between the Foot Pedal Weldment and the Pull Down Connecting Bar. This is a pivot

point, so do not over tighten the bolt.

11. Slip the Pull Down Yoke #9 through the slots in the Stand Top and attach it to the Pull Down

Connecting Bar with a 1/4 - 20 x 3/4'' hex head bolt, split lock washer, and hex nut.

12. Attach the aluminum Spotwelder Handle #10 to the Pull Down Yoke with 1/4 - 20 x 5/8 slot-

ted truss head screws.

13. Center the Duro Dyne Spotwelder on the stand and secure it using the Spotwelder Clamps

#11 and 1/4 - 20 x 5/8'' slotted truss head screws and 1/4'' wing nuts.

14. To change the pull down length, select a different hole in the Pull Down Connecting Bar or

loosen the Spotwelder Clamps, slide the spotwelder forward or backward, and tighten the

Spotwelder Clamps again.

81 Spence St. • Bay Shore • New York 11706

Phone: 631-249-9000 • Fax: 631-249-8346

ASSEMBLY INSTRUCTIONS

(over)