4iiii PM100 Manual de início rápido
Procurar online ou descarregar pdf Manual de início rápido para Instrumentos de medição 4iiii PM100. 4iiii PM100 2 páginas. Power meter
Também para 4iiii PM100: Manual de início rápido (9 páginas)
Imprimir página
FCC Compliance Statement
FCC ID: ZZNPM100
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interference that may cause undesired operation.
The grantee is not responsible for any changes or modi cations not expressly approved by the party responsible for compliance. Such modi cations could
void the user's authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit di erent from that to which the receiver is connected.
Consult the dealer or an expereince radio/TV technician for help.
Industry Canada (IC) Compliance Statement
IC: 9896A-PM100
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. CAN
ICES-3(B)/NMB-3(B)
The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS-102 RF exposure, users can obtain
Canadian information on RF exposure and compliance.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated
with a minimum distance of 20 centimeters between the radiator and your body.
Le present appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux
conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique reçu, même
si ce brouillage est susceptible d'en compromettre le fonctionnement du dispositf. CAN ICES-3(B)/NMB-3(B)
Le dispositif rencontre l'exemption des des limites courantes d'évaluation dans la section 2.5 de RSS 102 et la conformité à l'exposition et la conformité de rf.
Cet émetteur ne doit pas être co-placé ni fonctionnant en même temps qu'aucune autre antenne ou émetteur. Cet équipment devrait être installé et
.
actionné avec une distance minimum de 20 centimètres entre le radiateur et votre corps
Made in Canada by:
Contact us at
20301_D1
Quick Start Guide
For a complete User Manual go to 4iiii.com/precision
Getting Started!
First ride:
Next rides:
Follow all steps.
Wake up, Zero and Ride.
Load Battery into Cap
Ensure that battery, o-ring and cap lid
1
are functional and secure!
Cap
These pieces are critical to giving you a
water and dust tight seal and must be
rmly in place!
Positive side faces into the cap. Attach
the cap to your PRECISION pod.
2032 Battery
Reinstall
Wake-up
crank and pedals on your
PRECISION by rotating
bike and tighten to specs
the crank a few times
2
3