Datalogic S5N-MR-2-B01-PP Manual de instruções

Procurar online ou descarregar pdf Manual de instruções para Acessórios Datalogic S5N-MR-2-B01-PP. Datalogic S5N-MR-2-B01-PP 7 páginas.

Imprimir página

Datalogic S5N-MR-2-B01-PP Manual de instruções

This product is covered by one or more of the following patents.

European Patent 851,211 B1; 1,111,690 B1; 1,148,346 B1; 1,209,487 B1.

Italian Patent IT 1,321,772.

S5N-Mx-...-PP/NN SERIES

INSTRUCTION MANUAL

CONTROLS

OUTPUT LED (S5N-Mx...A00/B01/C01/C10/C21/D00/E01/F01/T01)

The yellow LED ON indicates that the N.O. (normally open) output

status is closed.

STABILITY LED (S5N-Mx...B01/C01/C21/E01/F01)

The green LED ON indicates that the received signal has a reserve

greater than 30% compared to the output switching value.

POWER ON LED (S5N-Mx...G00)

The green LED indicates that the sensor is operating.

TRIMMER (S5N-Mx...B01/C01/C21/E01/F01/T01)

The trimmer can be used to adjust sensitivity; the operating distance

increases turning the trimmer clockwise.

WARNING: The trimmer rotation is limited to 270° by a mechanical stop.

Do not apply excessive torque when adjusting (max 40 Nmm).

INSTALLATION

The sensor can be fixed by means of the M18x1 threaded body through

a  18 mm hole, using the two CH.24 nuts enclosed (22 Nm maximum

tightening torque).

Wide range of accessories available: various orientable fixing brackets

ease the sensor positioning (please refer to the accessories listed in the

general catalogue).

The operating distance is measured from the front surface of the sensor

lens.

C models: To improve the detection, the

object has to be moved closer or further away

from the front surface of the sensor lens.

In case of lateral translation, the object must

move as indicated in the figure.

CONNECTIONS

The connections are compliant to the EN 60947-5-2 standard.

S5N-Mx...G00

BROWN

10 ... 30 Vdc

WHITE

N.C. OUTPUT

BLACK

N.O. OUTPUT

BLUE

0 V

M12 CONNECTOR

AXIAL VERSION

2.5

TRIMMER

FIBRE OPTIC VERSION

Power supply:

Ripple:

Current consumption

(output current excluded):

Outputs:

Output current:

Output saturation voltage:

Response time:

Switching frequency:

Indicators:

Setting:

Operating temperature:

Storage temperature:

Dielectric strength:

Insulation resistance:

Operating distance (typical values):

10 ... 30 Vdc

TEST +

TEST -

Emission type:

0 V

Ambient light rejection:

Vibrations:

Shock resistance:

Housing material:

Lens material:

Mechanical protection:

Connections:

Weight:

AtEx 2014/34/EU

Setting of S5N-Mx...A00

Position the sensor and reflector on opposite sides.

Find the points where the yellow LED (OUT) is switched ON and OFF in both vertical and horizontal positions, and fix the sensor in the center

between these points.

Setting of S5N-Mx...B01/T01

Position the sensor and reflector on opposite sides.

DIMENSIONS

RADIAL VERSION

14.5

TRIMMER

M O D E L S

with trimmer

without trimmer

STABILITY LED

OUTPUT LED

72.5

14.5

6.2

TRIMMER

STABILITY LED

OUTPUT LED

54.5

TECHNICAL DATA

S5N-MA AXIAL VERSION

10 ... 30 Vdc (limit values)

2 Vpp max.

35 mA max.

N.O. and N.C.; PNP or NPN (short-circuit protection)

100 mA max.

2 V max.

0.5 ms (2 ms mod.F01/G00)

1 kHz (250 Hz mod.F01/G00)

OUTPUT LED (YELLOW) excluding mod.G00

STABILITY LED (GREEN) (mod.B01/C01/C21/E01/F01)

POWER ON LED (GREEN) (mod.G00)

sensitivity trimmer (mod.B01/C01/C21/E01/F01/T01)

-25 ... 55 °C

-25 ... 70 °C

500 Vac / 1 min. between electronic parts and housing

>20 M / 500 Vdc, between electronic parts and housing

A00: 0.1...4 M on R2

B01: 0.1...3.5 m on R2

C01: 0...60 cm

C10: 0...10 CM

C21: 0...35 cm

D00: 0.5...10 cm

F01/G00: 0...25 m

E01: 30 mm with OF-42 / 100 mm with OF-43

T01: 0.1...1 m on R2

red (630 nm) (mod. D00/E01) / red (660 nm) (mod.B01/T01)

infrared (880 nm) (mod. A00/C01/C10/C21/G00)

according to EN 60947-5-2

0.5 mm amplitude, 10 ... 55 Hz frequency, for every axis (EN60068-2-6)

11 ms (30 G) 6 shock for every axis (EN60068-2-27)

Nickel-plated brass

PMMA

IP67 Type 1 enclosure

2 m cable  4 mm / M12 - 4 pole connector

110 g. max. cable vers. / 60 g. max. connector vers.

II 3D EX tc IIIC IP67 T85°C

SETTING

Turn the sensitivity trimmer to the maximum position.

Moving the sensor both vertically and horizontally, determine the power on

and off points of the yellow LED (OUT) and then mount the sensor in the

middle of the points defined. Optimum operation is obtained when the

14.5

green LED (mod.B01) is ON and the yellow LED is OFF.

B01 models: If necessary reduce sensitivity in order to detect very small

targets. In order to improve alignment, repeat the procedure detailed

above whilst progressively reducing the sensitivity.

T01 model: Turn the sensitivity trimmer counterclockwise

until the yellow LED turns ON (pos.A).

Turn slowly the trimmer again clockwise until the yellow

LED turns OFF (Operating condition, pos.B).

Setting of S5N-Mx...F01/G00/E01 with OF-43 (P/R fibre-optics)

M O D E L S

Position the sensors (fibre terminals) on opposite sides.

with trimmer

without trimmer

Turn the sensitivity trimmer to maximum: moving the sensor both vertically

LED STABILITY

and horizontally, determine the power on and off points of the yellow LED

LED DI USCITA

(OUT) and then mount the sensor in the middle of the points defined.

Optimum operation is obtained when the green LED is ON and the yellow

LED is OFF (the output function and the relative LEDs are inverted in the

CABLE VERSION

E01 model with the OF-43 fibre).

If necessary, reduce sensitivity using the trimmer, in order to detect very

small targets. In order to improve alignment, repeat the procedure detailed

above whilst progressively reducing the sensitivity.

Setting of S5N-Mx...C01/C21/E01 with OF-42 (proximity fibre)

Turn the sensitivity trimmer to minimum: the green LED is ON, the yellow

LED is OFF. Position the target to detect in front of the sensor or of the

STABILITY LED

fibre terminals. Turn the sensitivity trimmer clockwise until the yellow LED

OUTPUT LED

turns ON (Target detected state, pos.A). Remove the target, the yellow

LED turns OFF. Turn the sensitivity trimmer clockwise until the yellow LED

turns ON (Background detected state, pos.B).

The trimmer reaches maximum if the background is not detected.

Turn the trimmer to the intermediate position C, between the two positions

A and B. The green LED must be ON.

S5N-MR RADIAL VERSION

Setting of S5N-Mx...C10/D00

The operating distance range of these sensors is factory preset: please

consider this feature when positioning.

TEST FUNCTION (S5N-Mx...G00)

The TEST+ and TEST- inputs can be used to inhibit the emitter and verify

that the system is correctly operating.

The receiver output should switch when the test is activated while the

beam is uninterrupted.

The inputs activating voltage range is 10 ... 30 Vdc.

B01: 0.1...2 m on R2

C01: 0...35 cm

Datalogic S.r.l.

C10: 0...8 cm

Via S. Vitalino 13 - 40012 Calderara di Reno - Italy

D00: 0...8 cm

Tel: +39 051 3147011 - Fax: +39 051 3147205 - www.datalogic.com

F01/G00: 0...20 m

T01: 0.1...1 m on R2

Helpful links at www.datalogic.com: Contact Us, Terms and Conditions, Support.

limiting the rights under copyright, no part of this documentation may be reproduced,

stored in or introduced into a retrieval system, or transmitted in any form or by any means,

or for any purpose, without the express written permission of Datalogic S.p.A. and/or its

affiliates. Datalogic and the Datalogic logo are registered trademarks of Datalogic S.p.A. in

many countries, including the U.S.A. and the E.U. All other trademarks and brands are

property of their respective owners. Datalogic reserves the right to make modifications

and improvements without prior notification.

MIN

MAX

For information about the disposal of Waste Electrical and

Electronic Equipment (WEEE), please refer to the website at

www.datalogic.com.

821005714 Rev. E