Cooke & Lewis CSS 1618 Manual de montagem

Procurar online ou descarregar pdf Manual de montagem para Mobiliário de interior Cooke & Lewis CSS 1618. Cooke & Lewis CSS 1618 2 páginas. Standard & tall dresser wall cabinets

Imprimir página
ASSEMBLY GUIDE
*** IMPORTANT INFORMATION ***
BEFORE YOU START
Installation should be performed by a competent person
only. This product could be dangerous if incorrectly installed.
Check the pack to ensure all of the components are included.
When you are ready to start, make sure that you have all of
the correct tools to hand, have plenty of space, and that the
area for building is clean and dry.
Do not rush! Read these instructions first and run through
the sequence before you begin. Assembly should be
carried out in the steps shown in the following diagrams,
constructing one unit at a time and keeping fittings together
to avoid loss. Lay large panels on the floor using the
packaging for protection. Do not overtighten screws, as this
may damage the cabinet.
If any items are missing, or problems arise with fitting,
please call the Manufacturers' Helpline on 01769 575500.
To clean - use mild soap and water only.
Do not use abrasive cleaners.
STEP 1:
Insert
into panels
and
as shown.
A
3
4
Then insert
and
into panels as shown.
B
C
IMPORTANT:
A
When fitting
Arrow points to
outside edge.
3
3
4
25mm
STANDARD & TALL DRESSER WALL CABINETS
15mm
HARDWARE:
25mm
12 x
A
2 x
15mm
F
15mm
15mm
12 x
8 x
B
J
12 x
C
15mm
15mm
15mm
25mm
25mm
25mm
30mm
Please use scissors to open the bag of fittings and then empty
30mm
30mm
the contents into a bowl, so that they do not get lost!
50mm
50mm
50mm
IMPORTANT: CAM FITTING AND LOCKING:
12
12
9
9
3
3
15mm
6
6
50mm
50mm
50mm
Press in
A
firmly.
Fully insert
B
.
Leave no gaps.
12
12
12
12
9
9
3
3
9
15mm
9
3
6
6
6
6
12
12
12
12
2
2
E
9
9
3
3
9
9
3
3
E
M
6
6
6
6
E
E
15mm
15mm
15mm
1
1
Attach the LH wall hanging bracket
and RH wall
M
hanging bracket
to both panels
, in the pre-marked
N
1
positions, using screws
.
E
30mm
50mm
WALL FIXINGS:
1 x
M
30mm
50mm
15mm
1 x
N
50mm
12
9
9
2 x
P
15mm
50mm
12
12
9
3
4 x
9
3
E
25mm
6
6
30mm
12
50mm
12
12
12
9
3
9
3
9
9
3
3
6
6
6
6
Turn
A
clockwise.
12
12
2
2
3
9
3
9
3
6
6
STEP 2:
50mm
Fixed shelf position:
N
Fit panels
to panel
.
3
1
Then fit panel
to panel
4
1
15mm
to the End Panel detail above for the
correct fitting position
Tighten the cams as you go (refer to
cam fitting and locking section above).
Then carefully slide panel
6
grooves.
MINIMUM TOOLS REQUIRED:
CROSS HEAD SCREWDRIVER
3
5
DRILL & DRILL BITS (3mm & 5mm)
12
3
3
1
6
6
HAMMER
12
12
9
9
3
3
SPIRIT LEVEL
6
6
12
12
2
2
1 x
1
LH End Panel
9
3
9
3
6
6
1 x
2
RH End Panel
2 x
Top & Base Panel
3
Turn to 2 o'clock to lock.
Framed Unit
Non-framed Unit
, referring
3
into the
CSS 1618
07/15
PANELS:
3
5
6
5
2
4
3
1 x
4
Fixed Shelf
2 x
5
Shelf
2 x
Back Panel
6
1
6
4
3
1