Austral Lock Gainsborough YARRA HORIZON FLAT OUTER PULL Instruções de instalação - Página 2

Procurar online ou descarregar pdf Instruções de instalação para Por fechaduras Austral Lock Gainsborough YARRA HORIZON FLAT OUTER PULL. Austral Lock Gainsborough YARRA HORIZON FLAT OUTER PULL 2 páginas.

Imprimir página

Fasten lock to door

•

If the Beaks of the Interior Assembly are extended, use

the Lever to retract them.

•

Remove the Handle Screws and lift the Interior Handle

off the Interior Base, place them aside.

•

Place the Exterior Assembly onto the exterior face of the

door stile. Rotate the protruding Spindle into a vertical

position.

•

While placing the Interior Base onto the interior face of

the door stile, note the following:

- Allow the protruding Spindle to enter the receiving slot

on the underside of the Interior Base.

- Locate the bosses on the underside of the Interior Base

into the holes in the door stile.

•

Pass the correct length Fixing Screws through the

Interior Base and screw firmly into the Exterior Assembly.

Install cylinder

(optional)

•

To install a Keyed Cylinder into the Interior

Assembly, remove and discard the Cylinder Plug

from the underside of the Interior Handle.

•

Install the Keyed Cylinder into the Interior Handle

matching the orientation shown in Figure E.

Fit interior pull

•

Place the Interior Handle over the Interior Base.

It may be necessary to rotate the Lever to find its

correct orientation. Refit the two Handle Screws.

•

Depress the Plunger and test the lock operation by

operating the Lever and Cylinder Key(s) if applicable.

NOTE: Ensure the Beaks are in the retracted

position before closing the door.

Catch plate installation

Reverse the Adjustment Screws 3 anti-clockwise turns from fully

'screwed-in' position.

Front Fix Catchplate Installation:

Remove the cover fix screws and the cover.

Close the door and position the Catch Assembly on the jamb

opposite the lock with a 1 to 2mm gap between the lock and Catch

Assembly. Mark the centre of the 'front fix' slots and drill 3.5mm

pilot holes.

Use two 'Front Fix' 9.5mm long screws to fit the Catch Assembly

lightly to the jamb. Gently close the door and operate the Lever to

test the Beak engagement. Move the CatchPlate Assembly up and

down and adjust the Catch Plate in and out to achieve the best fit.

Tighten the 'Front Fix' Catch Screws, refit the Cover and re-install

the cover fix screws.

Face Fix Catchplate Installation:

Leave the Cover in place. Mark the centre of the 'face fix' slots.

Screw to the jamb using two 'Face Fix' 25mm long screws. Adjust

catchplate position as described above.

Figure E

Interior Handle

Fixing Screw

Plunger

Handle Screw

SPACERS

Timber doors with a weather

seal and some aluminium

doors may require spacers

between the door and lock.

Figure F Front Fix Installation

Face Fix Installation

Door Jamb

Front Fix

Screws

Adjustment

Screws

Cover

In te ri

o r D o

e n te rs

o r

h e re

Cover Fix

Screws

"Front Fix" Screw

"Face Fix" Screw

9.5mm long

Installation

Interior base

The product must be installed according to the instructions included in the product packaging and the

door should be apertured according to the door "cut-out" dimensions and tolerances shown.

Beak

Cylinder Plug

Prior to fitting ensure that:

Keyed Cylinder

•

Doors stored on site are stored in a clean dry area free from cement, lime, paint, acid etc.

During fitting of the lock ensure that :

•

No metal swarf or other contaminants enter the lock body.

•

The fixing screws do not damage the product finish.

After installation of the door ensure that:

•

The door is correctly adjusted with the correct clearances.

•

The lock engages the catch plate correctly.

•

The door is protected from building fall-out such as wet plaster, mortar, and paint.

If the door becomes contaminated:

•

Do not paint the lock body or faceplate.

•

Remove wet plaster, cement, mortar and other droppings immediately, using clean water

and a sponge or rag, to avoid permanent staining or scratching of the product finish. If

removal is delayed and scraping becomes necessary the surface finish may suffer.

Maintenance

Annually inspect the door to confirm that the door operates with the correct clearances, closes and

opens without obstruction. Confirm that the lock beaks engage easily with the catch plate when the

door is closed and the lever or key is turned - adjust the door if necessary.

Annually check that when the door is closed, the lock can be locked by key and by the lever.

NB : The lock assembly has been lubricated for life, and should not be disassembled by the user.

Cleaning Powder Coatings

Every six months, powder coated surfaces should be cleaned to protect the finish. However, in areas

where pollutants are more prevalent, especially in coastal or industrial regions, cleaning should be

carried out every two to three months.

To clean the powder coated surface:

1. Carefully remove any loose deposits with a wet sponge.

2. Use a soft brush (non abrasive) or cloth and a mild household detergent solution to

remove dust, salt and other deposits. Do not use steel wool, scrapers, scouring liquids or

powders to remove deposits as these permanently scratch the coating surface.

Cleaning Chrome, Satin Chrome, Gold and Brass Finishes

Plated finishes are susceptible to tarnishing if they come into contact with moisture, wet paint,

or water vapour. All plated finishes should be coated with a non-abrasive furniture or car wax

Door Jamb

immediately after installation. Plated finishes should be regularly wiped with a non-abrasive

furniture or car wax, taking care not to scratch any protective finishes that are employed to protect

Face Fix

the surface and prevent tarnishing.

Screws

MAINTENANCE LOG

In te ri

o r D o

o r

e n te rs

h e re

9.5mm long

OEM1DOC01