Bender COMTRAXX COM465ID Manual de início rápido - Página 4
Procurar online ou descarregar pdf Manual de início rápido para Monitor Bender COMTRAXX COM465ID. Bender COMTRAXX COM465ID 4 páginas. Condition monitor with integrated gateway
Também para Bender COMTRAXX COM465ID: Início rápido (4 páginas), Manual de início rápido (4 páginas)
Imprimir página
Gerät in Betrieb nehmen
1. Das COM465ID per Ethernetkabel (RJ45) direkt mit
einem PC verbinden.
2. Alle angeschlossenen Geräte einschalten.
3. Internetbrowser auf dem PC starten.
4. Folgende Adresse im Internetbrowser eingeben:
169.254.0.1
5. Links in der NavigationBUSÜBERSICHT anklicken.
6. Die Kachel des COM465ID auswählen.
7. Etherneteinstellungen konfigurieren
Menü > Einstellungen > Schnittstelle > Ethernet
8. Nach erfolgreicher Konfiguration das Gerät mittels
RJ45 in das LAN einbinden.
Technische Daten
Bemessungsspannung .............................................................. AC 250 V
Bemessungs-Stoßspannung ..............................................................4 kV
Überspannungskategorie ..................................................................... III
Verschmutzungsgrad ..............................................................................3
Sichere Trennung (verstärkte Isolierung) zwischen
................................(A1/+, A2/-) –[(A-ID1, B-ID1), (A-ID2, B-ID2), (X2)]
Versorgungsspannung U
............................................ AC/DC 24...240 V
S
Frequenzbereich U
...........................................................DC, 50...60 Hz
S
Eigenverbrauch ...............................................................≤ 9,6 VA/≤ 4 W
Ethernet
Anschluss .............................................................................. RJ45
Datenrate ............................................10/100 MBit/s, autodetect
DHCP ................................................................................ein/aus
isoData
Schnittstelle/Protokoll ........................................RS-485/isoData
Betriebsart ........................................................................Master
Baudrate ........................................................................9,6 kBit/s
Leitungslänge ...........................................................................≤ 1200 m
Arbeitstemperatur .............................................................–25...+55 °C
Schutzart (IEC 60529)................................................................................
Einbauten .............................................................................. IP30
Klemmen .............................................................................. IP20
Alle Rechte vorbehalten.
Nachdruck und Vervielfältigung
nur mit Genehmigung des Herausgebers.
Bender GmbH & Co. KG
Postfach 1161 • 35301 Grünberg • Deutschland
Londorfer Str. 65 • 35305 Grünberg • Deutschland
Tel.: +49 6401 807-0 • Fax: +49 6401 807-259
E-Mail: [email protected] • www.bender.de
Commissioning the device
1. Connect the COM465ID directly to a PC via an
ethernet cable (RJ45).
2. Switch on all connected devices.
3. Start an internet browser on the PC.
4. Enter the following address in the Internet browser:
169.254.0.1
5. Click on the left hand side in the navigation
BUS OVERWIEW.
6. Select the COM465ID tile.
7. Configure the Ethernet settings
Menu > Settings > Interface > Ethernet
8. After successful configuration, connect the device
to the LAN via RJ45.
Technical data
Rated voltage .............................................................................AC 250 V
Rated impulse withstand voltage ......................................................4 kV
Overvoltage category ........................................................................... III
Pollution degree ....................................................................................3
Protective separation (reinforced insulation) between
................................(A1/+, A2/-) –[(A-ID1, B-ID1), (A-ID2, B-ID2), (X2)]
Supply voltage U
........................................................ AC/DC 24...240 V
S
Frequency range U
...........................................................DC, 50...60 Hz
S
Power consumption ........................................................≤ 9.6 VA/≤ 4 W
Ethernet
Connection ............................................................................ RJ45
Data rate .............................................10/100 MBit/s, autodetect
DHCP ..................................................................................on/off
isoData
Interface/protocol ...............................................RS-485/isoData
Operating mode ................................................................Master
Baud rate .......................................................................9.6 kBit/s
Cable length..............................................................................≤ 1200 m
Operating temperature ......................................................–25...+55 °C
Degree of protection (IEC 60529) ..............................................................
internal components ............................................................. IP30
terminals ............................................................................... IP20
only with permission of the publisher.
PO Box 1161 • 35301 Grünberg • Germany
Londorfer Str. 65 • 35305 Grünberg • Germany
Tel.: +49 6401 807-0 • Fax: +49 6401 807-259
E-Mail: [email protected] • www.bender.de
All rights reserved.
Reprinting and duplicating
Bender GmbH & Co. KG