Dymond Smart X 100 A Manual do utilizador

Procurar online ou descarregar pdf Manual do utilizador para Controlador Dymond Smart X 100 A. Dymond Smart X 100 A 1 páginas. Brushless speed controller

Imprimir página

Thanks for purchasing our SMART X Electronic Speed Controller (ESC). High power system for RC

models can be very dangerous, so please read this manual carefully. In that we have no control

over the correct use, installation, application, or maintenance of our products, no liability shall be

assumed nor accepted for any damages, losses or costs resulting from the use of the product.

Any claims arising from the operating, failure or malfunctioning etc. will be denied. We assume no

liability for personal injury, property damage or consequential damages resulting from our products

or workmanship.

As far as is legally permitted, the obligation to compensation is limited to the invoice amount of the

a ected product.

User Manual

Brushless Speed Controller

Smart X (50A / 100A)

03121571V3 / 03121573V3

FEATURES

- High-performance microprocessor with the operating frequency up to 50MHz brings excellent compatibility (with most motors in the market) and high driving eﬃciency.

- The maximum motor speed can reach 210000 RPM (for 2-poles), 70000 RPM (for 6-poles) and 35000 RPM (for 12-poles).

- Multiple ﬂight modes: Airplane Fixed Wing / Heli Governor Oﬀ / Heli Governor (Elf ) / Heli Governor Store.

- Adjustable throttle range, compatible with various transmitters. It brings smooth, soft & linear speed adjustment and rapid throttle response.

- Microprocessor powered by independent DC regulator has better anti-interference performance, which greatly reduces the risk of losing control.

- Built-in high-eﬃcient & high-power (switch mode) BEC can make the output voltage switched among 5.2V / 6.0V / 7.4V / 8.4V.

(For the speci c output voltage, please refer to the parameter list .)

- Brand new governor program, easy to operate; and its excellent speed-governing eﬀect can make big rotor blades more stable even under rapid load change.

- "Restart in auto rotation" can manually interrupt the auto rotation and quickly restart the motor to avoid crashes caused by incorrect operations.

- Independent output port for RPM (that is: motor speed) signals.

- Compatible LCD program box (optional accessory), its simple and visual interface allows users to set/revise all the ESC parameters easily.

(For detailed information, please refer to User Manual of LCD Program Box.)

- Upgradeable ﬁrmware, you can upgrade the ESC after connecting it to a PC via the USB cable on the program box.

- The independent port, for connecting the program box and setting parameters, can also be the output port of the running status data of the ESC. When coordinating with the data transmission

module, it can make the real-time data monitoring and logging possible.

- Multiple protection features including input voltage abnormality protection / low-voltage cutoﬀ protection / throttle signal loss protection eﬀectively prolong the service life of the ESC.

1) When set as "LiPo battery", the ESC will automatically calculate the cutoﬀ threshold of the battery pack according to the amount of LiPo cells. The low / middle / high cutoﬀ voltage per cell is 2.85V / 3.15V /

3.30V. For example, when using a 3S LiPo, if set the cutoﬀ voltage as "middle", the cutoﬀ threshold of this battery pack should be 3.15×3=9.45V.

2) When set as "NiMH battery", then the low / middle / high cutoﬀ voltage is 50% / 62.5% / 75% of the initial input voltage (at boot/starting up) . For example, when using a 6-cell NiMH battery pack,

the voltage at starting up is 1.44×6=8.64V; and if set the cutoﬀ threshold as "low", the cutoﬀ threshold of this battery pack should be 8.64×50%=4.3V.

3) When set as "Customized: 2.8V~25.2V", the cutoﬀ threshold of the battery pack can be precisely set (the precision can reach 0.1V). But you need a LCD program box (optional accessory) or USB cable on

the LCD program box to connect the ESC to a PC, then set relevant parameters via a special program (Hobbywing USB Link Software).

5, Flight Mode: Airplane Fixed Wing / Heli Governor O / *Heli Governor (Elf) / Heli Governor Store

1) Airplane Fixed Wing: The motor starts to spin at 5% throttle, then speeds up quickly and reaches the full speed from standstill in 300μs. In this mode, the ESC will be enforced to set the "Auto Rotation

Restart Time" to "OFF".

2) Heli Governor O : When the motor starts at 5% throttle, the startup is very soft and it takes 11 seconds to reach the full speed from standstill. In this mode, if the transmitter is in NORMAL state, then

usually the throttle curve is a slash (the start point is the lowest point / 0% throttle, the end point is the highest point / 100% throttle of the throttle range. And this throttle curve is often used by

beginners). As the start point is only 5% of the full throttle, the motor rotates slowly that greatly reduces psychological pressure for beginners, so pilots can select this mode for basic practices like

"frog leap". In this mode, the ESC will automatically set the "Auto Rotation Restart Time" to "Oﬀ".

3) Heli Governor (Elf) & Heli Governor Store: The motor only starts at 40% (or above) throttle (in governor mode, the motor won't start when the throttle value is within 0%-40%); its startup is very soft

and needs 11 seconds to reach the full speed from standstill. Besides, it has speed-governing function (works at 40%-100% throttle). As the motor rotates quickly in "governor" mode, so it isn't suitable

for beginner anymore but experienced pilots. In these two modes, the setting about "Auto Rotation Restart Time" comes into eﬀect (please refer to "Auto Rotation Restart Time" for more information).

4) Heli Governor (Elf) & Heli Governor Store have diﬀerent ways of storing target rev data. In "Governor Store" mode, the data are saved into the FLASH of the microprocessor (and the data won't disappear

after powered oﬀ ); while in "Governor (Elf )" mode, data of the nominal target rev are saved into the RAM of the microprocessor (and the data will disappear after powered oﬀ ).

• In "Governor (Elf )" mode, the ESC will automatically start the RPM standardization & regain the target rev data after powered on.

• In "Governor Store" mode, if it needs to re-standardize the target RPM, pilots must modify and save the ﬂight mode as any option except "Heli Govornor Store"ﬁrst (without restarting the ESC at this

moment), then modify and save it as "Heli Govornor Store"; the ESC will enter the RPM standardization and regain the target RPM data after it's powered on. After the ﬁrst activation of the

"speed-governing" function or changed accessories (like motor, battery cells amount, gear and diﬀerent type of main/big rotor blades) on the plane, pilots need to standardize the RPM again next time.

Here we suggest pilots take the "Governor Store" mode as their rst option to avoid standardizing rev every time.

a) RPM standardization in "Governor (Elf)" mode: when the throttle value switches to over 40% from 0%, the motor starts in a

super soft way and accelerates slowly; it completes RPM standardization in 11 seconds and then enters the "governor" mode.

After changed batteries, the ESC will standardize the RPM again.

b) RPM standardization in "Governor Store" mode: when the throttle value switches to over 40% from 0%, the motor starts in a

super soft way and accelerates slowly; it completes RPM standardization in 11 seconds and then enters the "governor" mode.

After ﬂight, please move the transmitter throttle stick to the bottom position, the motor stops spinning and the ESC will save

the standardized (target) RPM into the FLASH. After changed batteries, the ESC will read the target RPM from the FLASH, so

there is no need to standardize the rev again.

c) Example for RPM Standardization:

In this example, we take the neutral point (50%) of the throttle stick as reference points for standardizing RPM.

• Set the throttle curve (throttle value at the neutral point=50%) & pitch curve (the pitch at the neutral point is 0) in "NORMAL"

mode, and keep the throttle HOLD switch "locked" to ensure safety.

• Connect the fully charged battery to the ESC, let the ESC complete the initialization, then move the transmitter throttle stick to

the neutral point (here the throttle value at the neutral point is 50% and the pitch of main rotor blades is 0 degree), and then

"unlock" the throttle HOLD switch; the motor will start from standstill in a super soft way, accelerate slowly and completes the

target rev standardization 11 seconds later.

• Trial ﬂight. If the target rev is too low, then raise the throttle curve; if the target rev is too high, and then lower the throttle

PARAMETERS PROGRAMMING/SETTING VIA THE TRANSMITTER

4 steps to set parameters via the throttle stick:

I, enter "programming" mode,

II, select item(s),

III, select option(s) / parameters under item(s),

IV, exit "setting".

I, Enter "Programming / Setting" Mode

1. Turn on the transmitter, move the throttle stick to the top position (full throttle);

2. Connect battery to the ESC, then the motor emits "♪ 123" indicating the ESC is powered on normally .

3. 2 seconds later, the motor emits two short "beep-beep- ";

. .

4. 5 seconds later, the motor emits "♪ 56712" indicating it's already entered the "programming" mode.

III, Select Options / Parameter Values

The motor beeps in loops, move the throttle stick to the top position when heard some "beep(s)" tone

. .

indicating you selected its corresponding option value; then the motor will sound "♪ 1515" means the

value has been saved. (And if you don't want to set other items but quickly exit "setting", please move the

throttle stick to the bottom position in 3 seconds ; while if you still want to set other items, please wait

for returning to Step II and choose other items.

("*" in the form below indicate factory defaults)

Airplane

Fixed Wing

DECLARATION

Model

Main Application

Battery Count

Cont. / Burst Current

BEC Output

Input / Output Wire

Weight/Size

Battery

RPM

THRO

Smart X 50A:

• The tricolor (WRB) cable here is the throttle cable

(WHITE: throttle signal wire, RED: BEC output wire, Black: ground wire);

• The thin Orange wire is for RPM signal output;

• The 3-pin port (marked with - + P) is an independent port for parameter setting;

it can connect the LCD Program Box, or be the output port of running status data

of the ESC.

curve. E.g. set the throttle curve in IDLE1 / IDLE2 / IDLE3 mode to 65% / 75% / 85% respectively to experience diﬀerent RPM, and then adjust the value according to the actual situation or preference.

5) As the battery voltage decreases & the pitch of main rotor blades varies in ﬂight, so we recommend setting the throttle curve between 60%~85% (here we strongly suggest not set the value exceeds 85%) on

the transmitter to guarantee the speed -governing eﬀect and suﬃcient compensating room to keep the motor's constant speed. If still can't reach that target rev when the throttle value exceeds 85%, please

change the motor pinion.

6) For guaranteeing the speed-governing eﬀect, we strongly recommend setting the PWM frequency as 32 kHz.

6, Autorotation Restart Time: O / 5s / *10s / 15s / 30s / 90s.

This parameter is only used in "Governor (Elf )" and "Governor Store" modes, and works when the throttle value is within 5%~40%.

During the period of auto rotating (to land), pilots still have the chance to cancel the operation by interrupting the process and restarting the motor quickly. E.g. when set the parameter to 10 seconds,

enabling the throttle HOLD switch (to activate the throttle protection) in ﬂight, the motor will cut oﬀ the output and let the helicopter land. While, if you want to end this process immediately, then you need

to "unlock" the HOLD switch (to exit the throttle protection) and increase the throttle value to over 40%, and the ESC will temporarily switch the acceleration time to 1.5 seconds (that is: it reaches the full

speed from standstill in 1.5s) and output power quickly. This action protects the helicopter from crashing caused by the motor's slow acceleration. However, if "lock" the throttle HOLD switch over 10 seconds,

the ESC will still output power slowly at a super soft acceleration rate (that means it will take 11s to reach the full speed from standstill) even if you "unlock" the throttle HOLD switch and increase the throttle

value promptly.

Security Warning: For safety, please pay attention to the following points.

• When the landing process ends early and the helicopter gets back to ground before the "autorotation restart time", it's prohibited to "unlock" the throttle HOLD switch before disconnecting the battery.

Otherwise, the helicopter may rotate and accelerate to a high speed in 1.5s and cause accidents. E.g., if "unlock" the throttle HOLD switch in the "Auto rotation restart time" with the helicopter is still in "IDLE"

mode, main rotor blades will spin rapidly and the helicopter may drift and tilt even on the ground.

• If switch the ﬂight mode from "IDLE" to "NORMAL" and move the throttle stick to the bottom position (0% throttle) or "lock" the "Throttle Cut" switch on the transmitter, main rotor blades will not rotate even if

you accidentally "unlocked" the throttle HOLD switch.

• In "governor" mode, if set "Auto Rotation Restart Time" to "Oﬀ", the motor will always restart at the super soft acceleration rate (it takes 11 seconds to reach the full speed from standstill). Please attention!

7, Advanced Timing: 0deg / 4deg / 8deg / 12deg / *15deg / 18deg / 22deg / 26deg / 30deg / Customized: 0deg~30deg, step: 1 deg.

In general, the low timing works ﬁne for most motors. While as great diﬀerences exist among motors, so please try diﬀerent timing(s) to get the best driving eﬀect. For increasing the speed, you can set the

timing higher. After the timing adjustment, we recommend having a trial on the ground ﬁrst, and then ﬂy in the sky.

Throttle (NORMAL)

Throttle (IDLE)

8, PWM Frequency: 8KHz / 16KHz / 24KHz / *32KHz

100%

The rise of PWM frequency can make the motor driving smoother and the noise lower; certainly, this will bring more switching loss for the MOSFET & more heat to the ESC.

50%

9, BEC Voltage: *5.2V / 6.0V / 7.4V / 8.4V

For Smart X 50A ESCs, the BEC output voltage is selectable among 5.2V / 6.0V / 7.4V; and the actual output will be 7.4V even if you selected 8.4V as the nominal output.

-100%

Neutral

100%

Throttle

-100%

Neutral

100%

Throttle

Point

For Smart X 100A ESCs, the BEC output voltage is selectable among 6.0V / 7.4V / 8.4V; but the actual output will be 6.0V even if you selected 5.2V as the nominal output.

Stick

Position

10, LiPo Cells: *Auto calculation / 1 cell / 2 cells / 3 cells / 4 cells / 5 cells / 6 cells

Pitch(IDLE)

Pitch(NORMAL)

The parameter is valid only when the battery pack is LiPo. After powered on, the ESC will make the motor beep the amount of cells in your LiPo pack according to auto-detection or cell count manually set.

12°

For Smart X 50A/100A V3 ESCs, the range which can be auto-calculated or manually set is 2~6S; if exceeds, the ESC will warn.

-100%

Neutral

100%

Throttle

Before using a new ESC, you need to check all the connections to make sure they are correct and reliable before connecting the ESC to the battery. When ensured everything is ok, then start the ESC in the

Neutral

100%

Throttle

Point

Stick

-100%

Point

Stick

Position

following sequence:

Position

1, Move the throttle stick to the bottom position (throttle value=0%), then turn on the transmitter;

2, Connect the battery pack to the ESC, then the ESC starts self-test; the motor issues "♪ 123" indicating the system is powered on, and N short "beeps" indicating the amount of LiPo cells of the battery pack,

The example of throttle curve and pitch curve for RPM standardization

then a long "beep—"indicating the self-test is completed successfully and the system is ready to ﬂy.

• If no response is received, please check the battery and battery connections to ensure they are ok and reliable.

In the example below, it set the "ﬂight mode" to "Heli Governor Oﬀ" , that is the 2

II, Select Items

I, Enter "programming" mode：Move the throttle stick to the top

After entered the "programming" mode, you can hear 12 sets of tone repeat

position and then turn on the transmitter, connect ESC to battery, the

sequentially. Move the throttle stick to the bottom position in 3 seconds after the

motor emitted certain set of tone, and then you enter the corresponding item.

motor emits "♪ 123" indicating it's normally powered on. 2 seconds

1. Brake

(1 short)

"B"

later, it emits "beep-beep-" and then 5 seconds later it emits "♪ 56712 "

2. Battery Type

(2 short)

"BB"

which indicates it's already entered the "programming" mode.

3. Cutoﬀ

(3 short)

"BBB"

4. Low-voltage Cutoﬀ Threshold (4 short)

"BBBB"

5. Flight Mode

(1 long)

"B—"

6. Auto Rotation Restart Time

(1 long & 1 short)

"B—B"

7. Timing

(1 long & 2 short)

"B—BB"

8. PWM Frequency

(1 long & 3 short)

"B—BBB"

9. BEC Voltage

(1 long & 4 short)

"B—BBBB"

10.LiPo Cells

(2 long)

"B—B—"

Trouble

11. Reset to Factory Default

(3 long & 1 short)

"B—B—B—B"

After powered on, the motor doesn't rotate and there is no sound emitted.

12.Exit

(3 long & 2 short)

"B—B—B—BB"

After powered on, the motor doesn't spin, but emits the warning tone

Note: as 1 long "Beep—" equals to 5 short "beep-", e.g, in step II "Select Items" , 1

long & 1 short ("Beep—Beep") represents option 6.

"beep beep, beep beep, beep beep" (the interval between each group of

"beep beep" is 1 second).

After powered on, the motor doesn't spin but emits the warning tone

"beep-, beep-, beep-" (the time interval each "beep-" is 2 seconds).

IV, Exit "Setting"

After powered on, the motor doesn't run but emits "beep, beep, beep,

beep, beep" (each beep is very short and hurried).

Two ways to exit "setting" mode:

a) In Step III, after heard the special tone

After powered on, the motor doesn't run but emits "beep-beep" then the

. .

special tone "♪ 56712 ".

"♪ 1515" while selecting optional values,

The motor rotates in the wrong direction.

move the throttle stick to the bottom

position in 2 seconds, then you exit

"setting".

b) After heard 3 long & 2 short beeps

The motor stops halfway.

which represent item 12 while selecting

options in Step II, move the throttle

stick to the bottom position in 3

seconds, then you exit "setting".

Note: After revised ESC parameters via the transmitter

throttle stick or program card/box, please save those

settings and exit; then the motor emits 5 long

"beep-" and 5 seconds later you can restart the ESC.

SPECIFICATIONS

Smart X 100 A

Smart X 50 A

Planes and 480-550 heli (425-550mm blade)

Planes and 450 & 450L heli (325-380mm blade)

2-6S Lipo, 5.2V-25.2V

100A /150A (burst in 10 sec)

50A /75A (burst in 10 sec)

Switch Mode BEC, 6.0V / 7.4V / 8.4V; Cont.: 10A, Burst: 25A

Switch Mode BEC, 5.2V / 6.0V / 7.4V

BEC has the cut-through protection (which means the battery voltage

Cont.: 7A, Burst: 15A

won't get through to the receiver if the BEC is accidentally damaged)

Input: 12AWG / Output:12AWG

Input: 14AWG / Output: 14AWG

104g / 70mm x 35mm x 21mm（W/O Fan）

49g / 48mm x 30mm x 15.5mm

110g / 70mm x 35mm x 32mm（With Fan）

WIRING DIAGRAM

Battery

DYMOND

LCD PROGRAM BOX

RPM

BEC

DYMOND

THRO

Smart X 50 A

Smart X 100 A

Smart X 100A

• The tricolor (WRB) cable here is the throttle cable

(WHITE: throttle signal wire, RED: BEC output wire, BLACK: ground wire);

• The bicolor (RB) cable here is the BEC cable (RED: BEC output wire, BLACK: ground wire);

• Hence, there are 2 Black wires & 2 Red wires are connected in parallel to the output end of the BEC to make the

higher current get through;

• The thin Orange wire is for RPM signal output;

• The 3-pin port (marked with - + P) is an independent port for parameter setting; it can connect LCD Program

Box, or be the output port of the ESC running status data. 2 pins corresponding to "+" & "-" in the program port

are also connected to the output end of the built-in BEC, so that it can power the cooling fan of the ESC.

BEGIN TO USE A NEW BRUSHLESS ESC

ESC PROGRAMMING SAMPLE

parameter of item 5.

II, Select items: motor starts to sound,

III, Select Options：motor emits a short

when heard a long "beep—" (which

"beep-", 3 seconds later, two short

represent Item #5—ﬂight mode), move

"beep-beep-", then move the throttle stick to

. .

the throttle stick to the bottom

the top position, and the motor emits "♪ 1515"

position, then you entered this item

indicating it has set to "Heli Governor Oﬀ".

TROUBLESHOOTING

Cause

Solution

Poor connection between power connectors.

Re-plug or change the connectors.

The battery voltage is abnormal.

Please check the battery voltage.

Please check whether the communication between the transmitter

No signal output from the throttle channel of the receiver.

& receiver is normal or not, and if the control wire (that is, Rx wire) has

been ﬁrmly plugged into the throttle channel in the correct direction.

Didn't move the throttle stick to the bottom position or

Move the throttle stick to the bottom position or reset the throttle range.

the throttle range is too narrow.

Please refer to the transmitter's user manual and reset the "Normal /

Incorrect "Normal / Reverse" direction of the throttle channel.

Reverse" direction of the throttle channel.

Connected ESC output wires to motor wires in the wrong order.

Swap any of two wire connections.

Please check the communication between the transmitter & receiver,

Throttle signal loss protection is activated.

and also check the connection between ESC and the receiver.

Low-voltage cutoﬀ protection is activated.

Charge the battery pack or change a new one.

Please check the battery connector and the connection between ESC

Poor wire connections.

output wires and motor wires.

Smart X series speed controllers have independent output ports / interfaces for RPM signals, so it can connect to ﬂybarless systems like Mikado V-Bar as RPM signal source. Undoubtedly, this reduces

peripheral devices which need to be connected to the ﬂybarless helicopter and simpliﬁes the wiring.

"*"in the form below indicate factory defaults.

Item

Option

Brake

*Oﬀ

Soft

Battery Type

*LiPo

NiMH

*Soft cut

Hard cut

Low-voltage

Oﬀ

Low

DYMOND

LCD PROGRAM BOX

Flight Mode

Airplane Fixed Wing

Heli Governor Oﬀ

Auto Rotation Restart Time

Oﬀ

5sec

Advanced Timing

0deg

4deg

PWM Frequency

8KHz

16KHz

BEC Voltage

*5.2V

6.0V

Lipo Cells

*Auto calculate

1 cells

"*"in explanations below indicate factory defaults.

1, Brake: *Oﬀ / Soft / Hard / Very hard

2, Battery Type: *LiPo / NiMH

: *Soft cut / Hard cut. Soft means gradually reduce the output power. Hard means cut oﬀ the output immediately.

: Oﬀ / Low / *Middle / High / Customized: 2.8V~25.2V，Step: 0.1V

• If the motor doesn't beep after powered on, it means the battery voltage is too low or too high. Please check the battery voltage.

• If the motor sounds "beep-beep-" 2 seconds after powered on, and "♪ 56712 " 5 seconds later to indicate the ESC is entering the "programming" mode, it means the throttle channel direction in your

transmitter is reversed, in such a case you need to reset the "Normal / Reverse" direction of the throttle channel by referring to the transmitter's manual.

3, Attention！

To ensure the ESC ﬁts well with the throttle range on your transmitter, you need to reset the throttle range when using this ESC for the ﬁrst time or changed another transmitter for the optimum throttle

linearity. For detailed operation, please refer to the explanation in 《Set the Throttle Range》.

1. Warning tone for abnormal input voltage: when powered on the ESC, it will start testing the input voltage. If the voltage is not in the normal scope, the motor will emit the warning "beep beep, beep beep,

beep beep" till the voltage returns to normal (the time interval among each group of "beep beep" is 1 second).

2. Warning tone for throttle signal loss: when detected no throttle signal, the ESC will issue the following warning: "beep-, beep, beep-" (the time interval among these "beeps" is 2 seconds).

3. Warning tone if the throttle stick is not at the bottom position when the ESC is powered up: When the throttle is not at the bottom position, the ESC will issue the following warning:

"beep-beep-beep-beep-beep-" (every "beep" is very short and hurried).

1. Startup Protection: the ESC will shut down the motor after failed to start the motor normally in 2 seconds by increasing the throttle value, then you need to move the transmitter throttle stick to the

bottom position again and restart.

(Causes to this problem: poor wire connection between the ESC and the motor or disconnection of some output wire, propellers are blocked by other objects, gears are blocked and cannot move and etc.)

2. Overheat Protection: When the internal operating temperature exceeds 110 Celsius degree, the ESC will reduce its output power and start protection; it won't cut oﬀ the output, but reduce it to 50% to

ensure that the motor still has some power for avoiding crash caused by insuﬃcient power. And the ESC will gradually resume its maximum power after the temperature returns to the safe level.

3. Throttle Signal Loss Protection: When detected the signal loss for over 0.25 second, the ESC will cut oﬀ the output immediately to avoid even greater loss which may caused by the continuous high-speed

rotation of propellers or rotor blades.

4. Overload Protection: The ESC will cut oﬀ the power or restart automatically when the load suddenly increases to a very high value. And the common cause of load soar is the lockout of propellers.

Turn on the transmitter and move the

Connect battery to the ESC, the

throttle stick to the bottom position

motor will emit "♪123" indicating

(Throttle value=0%).

the ESC is powered on normally.

Attention! It is necessary to reset the throttle range when using a new ESC or changed another transmitter.

Turn on the transmitter, and

Connect battery to the

move the throttle

ESC, and the motor emits

"♪123" indicating the ESC is

stick to the top

powered on normally.

position (full throttle).

IV, Exit "setting"： After

the 3rd step completed,

move the throttle to the

. .

bottom position again

in 2 seconds.

2015, DYMOND MODELLSPORT

OUTPUT PORT FOR RPM SIGNALS

PROGRAMMABLE ITEMS

Hard

Very hard

Customized:

*Middle

High

2.8V-25.2V, Step:0.1V

*Heli Governor (Elf )

Heli Governor Store

*10sec

15sec

30sec

90sec

Customized:

8deg

12deg

*15deg

18deg

22deg 26deg

30deg

0deg-30deg, Step:1deg

24KHz

*32KHz

7.4V

8.4V

2 cells

3 cells

4 cells

5 cells

6 cells

PROGRAMMABLE ITEMS

. .

EXPLANATIONS FOR WARNING TONE

EXPLANATION FOR OTHER PROTECTIONS

NORMAL START-UP PROCESS

Then motor emits several

And a long "beep" indicating the

short "beeps" to indicate the

system is ready and you can ﬂy the

amount of LiPo cells.

helicopter or airplane now.

SET THE THROTTLE RANGE

2 seconds later, the motor

Move the throttle stick to the bottom

The motor emits N

Then a long "beep"

emits 2 short "beep-beep-"

position, await 1 second

beeps to indicate

indicates the system

indicating the top position is

then the bottom position

the amount of

is ready and you can

calibrated successfully.

is calibrated Successfully.

Lipo cells.

ﬂy the aircraft now.

Gustav Staufenbiel GmbH

Hanskampring 9

D-22885 Barsbüttel

www.modellhobby.de

Tel.: +49 -40 300 61950

Mail: [email protected]