Adelphia 18350 Manual do utilizador

Procurar online ou descarregar pdf Manual do utilizador para Controlo remoto Adelphia 18350. Adelphia 18350 2 páginas. 4-in-1 cable tv remote control for scientific-atlanta explorer set-top boxes

Imprimir página

User's Guide for the

4-in-1 Cable TV Remote Control

for Scientific-Atlanta

Explorer Set-Top Boxes

Use this guide in conjunction with your cable

set-top box manual

Part Number ICX18350, version 2.0

02102005

SmartScan™ Automatic Programming

™

SmartScan

will allow you to easily try all the available programming codes for the selected

device and find the best match. If you prefer manual programming or already have the device

codes you may also program the remote manually using the steps in section 6.

Turn on the power for the device to be programmed.

Begin the SmartScan

™

procedure by pressing and holding the associated device key

(AUX, VCR/DVD, TV) until all device keys on the remote begin to flash (approximately 3

seconds). Release the device key.

If the device you're attempting to program matches the selected device key (e.g. TV

component with the TV device key) proceed to step 5.

If the device you're attempting to program does not match the selected key (e.g. a

second VCR programmed to the AUX device), locate the correct prefix code for the

device you wish to program from the table listed below. Press and release the number

key that matches the prefix code.

Prefix

Press and release the POWER key. The device key will stop flashing and remain on.

Point the remote control at the selected device.

Press and hold the UP ARROW key until the device turns off. While holding the UP

ARROW key the remote will send a new code approximately once every second. The

device button will blink each time a new code is sent. If you pass the code that turns off

the device, press the DOWN ARROW key to return to the previous code.

When the device turns off, you have found a candidate code. Press the POWER key to

turn device back on. Test various functions using the remote control to determine if this

code will work. If primary functions do not work, make sure the device is still on then

™

resume SmartScan

by pressing the UP ARROW key to find another device code.

Once you have found a satisfactory code, press SEL to lock the code. The power of the

device must be on. The device key will then flash three times. Go to section 10 to recall

and record your device codes. When all the codes have been attempted the device

button will flash rapidly.

Manual Programming

To manually set up the Adelphia remote to operate a device, find the manufacturer of the

device in the list of manufacturers' codes. The codes are logically grouped by device type in

section 12. Once you find the code, perform the following steps:

Press and hold the device key to be programmed until all device keys begin to flash

(approximately 3 seconds). Release the key. The selected device key will continue to flash.

Enter the four digit code for the desired device using the number keys. After pressing the

first digit, the device key will light and remain on. After the last digit is pressed the device

key will flash three times and turn off. You will not see any flashes if the code has failed.

Congratulations!

This four mode remote control has been

programmed to control your Scientific-

Atlanta set-top box and can be

programmed to control up to three

additional entertainment components by

following these easy instructions.

Before You Begin

Please plug your television power cord

into a separate wall outlet instead of the

power outlet on the cable box.

Tune your television to channel 2, 3 or 4

as directed by your cable provider.

Install Batteries

Two AAA alkaline batteries must be

installed before you can program or

operate the remote control.

1. Remove the battery compartment cover

located on the back of the remote control.

2. Place the batteries in the compartment

in positions matching the picture below.

3. Replace the battery compartment cover.

IMPORTANT

NOTE

Use only new AAA Alkaline

batteries to insure consistent

operation.

Device

VCR/DVD

Audio Receivers

TV Combo Units

Know Your Remote

The diagram below provides a brief description of each key on your Adelphia remote control.

The function descriptions will allow you to become more familiar with your remote. Functions

may vary between different services. Please refer to your set-top box manual for descriptions of

specific functions.

The Adelphia remote control is already programmed with the code for your Scientific-Atlanta

top box. The following sections will help you program your remote to control your other

entertainment components.

Test the code by trying various functions. If the primary function keys fail to respond

satisfactorily try the next code listed for the manufacturer.

If you have tried all the codes listed for the manufacturer and the device does not

respond, try to program the device using SmartScan

Remember to record your device codes in section 11 when you are done.

Programming Volume Control

By default, your Adelphia remote controls volume through the TV. To allow volume control

through a different device:

Press and hold the CBL device key until all the device keys begin to flash. Release the

CBL key. The CBL key will continue to flash.

Press and release the VOLUME UP key, the CBL key will remain on.

Press and release the VOLUME DOWN key. The CBL key will turn off when VOLUME

DOWN is pressed, and will turn on when released.

Press and release the key corresponding to the device you wish to use to control

volume (CBL or AUX). After you release the key, the CBL key will flash three times and

turn off.

To return volume control to the default state:

Press and hold the CBL device key until all the device keys begin to flash. Release the

CBL key. The CBL key will continue to flash.

Press and release the VOLUME UP key. The CBL device key will stop flashing and stay

on. Press and release the VOLUME DOWN key, and then press and release the SEL key.

After you release the SEL key, the CBL device key will flash three times and turn off.

Master Power Control

The Master Power function allows you to turn off and on two or more devices

simultaneously with a single press of the power button. The following steps describe how

to program the Master Power Control function:

Press and hold the CBL device key until all the device keys begin to flash. Release the

CBL key. The CBL key will continue to flash.

Press and release the POWER key.

Individually press and release each device key corresponding to the components you

wish to be controlled by Master Power (starting with the cable device key). NOTE: If no

keys are pressed in this step, no change will occur in Master Power programming.

Press and release the POWER key. The CBL key will flash three times and turn off.

Manually turn on all devices. Then test the Master Power control by pressing the

POWER key.

To disable Master Power, repeat the previous steps selecting only one device for Master Power

(any device can be selected). The remote will now control the power ON/OFF of each device

separately.

NOTE: Once Master Power has been programmed for two or more devices, pressing the POWER

key in normal operation will cause the remote to transmit the POWER on/off commands for

those devices selected during Master Power programming,

To override this and transmit a POWER on/off command for a device not included in the Master

Power selection, press the DEVICE key for that device and immediately press the POWER key.

set-

™

as described in section 5.