Gaggenau VG 232 CA Manual de instruções de funcionamento e montagem - Página 4
Procurar online ou descarregar pdf Manual de instruções de funcionamento e montagem para Placa de fogão Gaggenau VG 232 CA. Gaggenau VG 232 CA 20 páginas. Gas cooker vg 232 ca operating and assembly instructions
Também para Gaggenau VG 232 CA: Manual de instruções de funcionamento e montagem (14 páginas)
Imprimir página
Warnings
1. Do not allow the flame to extend beyond the
edge of the cooking utensil. This instruction is
based on safety considerations.
2. Do not forget that the unit becomes hot when in
use. Common sense is important. Just because
the flame is out, it does not mean parts still
cannot be hot.
3. This appliance shall not be used for space
heating. This instruction is based on safety
considerations.
4. Be sure to disconnect the electrical supply
before disassembly of the appliance.
5. Keep the appliance area clear and free from
combustible materials, gasoline and other
flammable vapors and liquids.
6. Do not obstruct the flow of combustion and
ventilation air.
7. Cabinets installed above the gas cooktop must
have a minimum distance of 600 mm (24 ´ ´ ).
8. The gas pressure regulator supplied with the
appliance must be installed in line with the gas
pipe.
9. The appliance and its individual shutoff valve
must be disconnected from the gas supply
piping system during any pressure testing of the
system at test pressures in excess of 3.5 kPa
(1/2 psig). The appliance must be isolated from
the gas supply piping system by closing its
individual manual shutoff valve during any
pressure testing of the gas supply piping system
at test pressures equal to or less than 3.5 kPa
(1/2 psig).
10.Important:
When using a very large pot, keep a distance of
at least 50 mm (2") to avoid damaging any parts
in counter top wood, plastic or other non-heat-
resistant materials. Never leave oil or hot fat
unattended.
Note: To avoid jeopardising the electrical safety of
the appliance, it is forbidden to use high-pressure
or steam jet cleaning devices.
Note: The name plate is attached to the bottom of
the unit and to the inside of the housing.
Only for Installation in USA:
This installation must conform with local codes or, in
absence of local codes, with the National Fuel Gas
Code, ANSI Z 223.1 Current Issue.
The installer must leave these instructions with the
appliance, and the consumer should keep them for
future reference. If an external electrical source is
utilized, the appliance must be electrically
grounded in accordance with local codes, with the
National Electrical Code ANSI/NFPA 70 Current
Issue.
For Massachusetts Installations:
1. Installation must be performed by a qualified or
licensed contractor, plumber or gas fitter
qualified or licensed by the state, province or
region where this appliance is being installed.
2. Shut-off valve must be a "T" handle gas cock.
3. Flexible gas connector must not be longer than
36 inches.
Only for Installation in Canada:
In Canada, installation must be in accordance with
the CAN 1-B149.1 and .2 – Installation Codes for
Gas Burning Appliances and/or local codes. The
installer must leave these Instructions with the
appliance and the Consumer should retain them for
future reference.
This appliance when installed, must be electrically
grounded in accordance with local codes or, in the
absence of local codes, with the current CSA
Standard C 22.1-Canadian Electrical Code, Part I.
For mobile Housing and Recreational Vehicle
installation must conform with the following:
CAN/CSA Z240 MH
CAN/CSA Z240 RV
Installation Requirement For Gas Burning
Appliances And Equipment In Mobile Homes CSA
Standard C 22:1 - Canadian Electrical Code Part 1
and /or local Codes.
3