Gaggenau VG 414 210 AU Manual de instruções de instalação - Página 8
Procurar online ou descarregar pdf Manual de instruções de instalação para Placa de fogão Gaggenau VG 414 210 AU. Gaggenau VG 414 210 AU 12 páginas. Gas wok
Também para Gaggenau VG 414 210 AU: Manual de instruções (16 páginas)
Imprimir página
VA 420 000
Connection strip for combination with other
Vario 400 appliances for flush installation
VA 420 001
Connection strip for combination with other
Vario 400 appliances for flush installation
with appliance cover/extension
VA 420 010
Connection strip for combination with other
Vario 400 appliances for surface
installation
VA 420 011
Connection strip for combination with other
Vario 400 appliances for surface
installation with appliance cover/extension
VA 440 010
Stainless steel appliance cover
VA 450 400
Appliance extension, 38 cm
Only use the accessories as specified. The manufacturer
accepts no liability if these accessories are used incorrectly.
Preparing the cabinet (Fig. 1a)
The kitchen unit must be heat-resistant to at least 90°C (about
190°F). The stability of the unit must be maintained after
producing the cut-out.
Produce the cut-out in the worktop for one or more Vario
appliances as shown in the installation sketch. The angle
between the cut surface and the worktop must be 90°.
The cut edges at the sides must be flat to ensure a good fit of
the retaining springs on the appliance. In laminated worktops, it
may be necessary to fit strips at the sides of the cut-out.
Remove shavings after cutting. Seal cut surfaces for resistance
to heat and so they are watertight.
Pay attention to a minimum gap of 10 mm from the underside of
the appliance to kitchen units.
Use suitable base constructions to ensure load-carrying
capacity and stability, especially in the case of thin worktops.
Pay attention to the weight of the appliance, including any
payload. Reinforcement material used must be resistant to heat
and moisture.
Note: Wait until the appliance has been installed in the
installation opening before checking that it is level.
Flush installation (Figure 1b)
Flush installation in a worktop is possible.
The appliance can be installed in the following temperature-
resistant and waterproof worktops:
Stone worktops
■
Worktops made of plastics (e.g. Corian
■
Solid wood worktops: Only by arrangement the with worktop
■
manufacturer (seal recess edges)
For other materials, coordinate with the worktop manufacturer
■
with regard to use.
Installation in laminated wood worktops is not possible.
Note: All recessing work on the worktop must be performed in a
specialist workshop on the basis of the installation sketch. The
recess must be produced neatly and precisely because the cut
edge is visible on the surface. Clean and degrease the recess
edges with a suitable cleaning agent (observe the silicone
manufacturer's processing notes).
Fitting several Vario appliances (Fig. 1c)
You can order the connecting strip VA 420 000/001/010/011
as a special accessory to combine several Vario appliances.
Allow for the additional space required for the connecting strip
when producing the cut-out (see installation instructions
VA 420 000/001/010/011).
Appliances can also be fitted in individual recesses, if a
minimum ridge width of 50 mm between the recesses is
observed.
To enable combination of appliances with and without an
appliance cover, dimension differences can be balanced out by
the extension VA 450 110/-400/-600/-800/-900 (depending on
appliance width).
Combination with the appliance cover (Fig. 1d)
You can order the appliance cover VA 440 010 as a special
accessory. Allow for the additional space required for the
appliance cover when producing the cut-out.
)
®
Boring to fit the control knob (Fig. 2a + 2b)
Thickness of cabinet front: 16 - 26 mm
As shown in the installation sketch, drill the Ø 35 mm hole to
1.
secure the control knob in the cabinet front. Attach the
enclosed stencil to the cabinet front for correct positioning of
the bore.
If the cabinet front is thicker than 26 mm, the front must be
2.
routed from the back to max. 26 mm on an area of
80 x 310 mm.
Fitting the appliance
Lower the appliance evenly into the cut-out and press down
1.
firmly (Fig. 6a).
Note: The appliance should fit tightly in the cut-out without
moving around (e.g. during cleaning). If the cut-out width is on
or above tolerance limit it may be necessary to fit filler strips to
the sides of the cut-out.
Turn control knobs to the OFF position. Assemble the spindle
2.
between the control knob and the gas tap. Firmly slide the
spindle drive onto the gas tap. Fix the spindle in position with
the retaining screw (Fig. 6c).
Connect the appliance to the power and gas supply and test
3.
for correct functioning. There might be an air pocket in the gas
supply line if the appliance switches off. Turn control knobs off
and switch on again. Repeat until burner ignites.
Only for flush fitting (Fig. 6b): Check appliance for correct
4.
functioning before applying sealant! Fill the surrounding gap
between the work surface and the frame with a suitable, heat-
resistant silicone adhesive (e.g. OTTOSEAL
the sealing joint using the smoothing agent recommended by
the silicone manufacturer. Check the usage information for the
silicone adhesive. Do not use the appliance until the silicone
adhesive has completely dried (at least 24 hours depending
on room temperature).
Caution!
Unsuitable silicone adhesives can cause permanent
discolouration on work surfaces made from natural stone.
Removing the appliance
Disconnect the appliance from the power and the gas supply.
For flush-mounted appliances, remove the silicone joint. Push
out the appliance from below.
Caution!
Damage to appliance! Do not lever out the appliance from
above.
Gas connection
The supply connection point shall be accessible with the
appliance installed.
Using the R½'' (for appliance side) connection elbow provided,
connect the appliance with the associated gasket to a fixed
connection pipe. For natural gas the regulator must be
connected.
If using a flexible connection
This appliance is approved for connection by a CLASS B hose.
Connection is in compliance with AS/NZS 5601.1
There are two ways to carry out the connection to the main gas
line:
A: The hotplate can be connected with rigid pipe.
■
B: Flexible Hose: If installing with a hose assembly, install with
■
a hose assembly that complies with AS/NZS 1869 (AGA
Approved), 10 mm ID, class Bor D, no more than 1.2 m long
and in accordance with AS/NZS 5601.1. Ensure that the hose
does not contact the hot surfaces of the hotplate, oven,
dishwasher or any other appliance that may be installed
underneath or next to the hotplate. The hose should not be
subjected to abrasion, kinking or permanent deformation and
should be inspected along its entire length with the cooktop in
the installed position. Unions compatible with the hose fittings
must be used and all connections tested for gas leaks.
Before leaving - check all connections for gas leaks with soap
and water. DO NOT use a naked flame for detecting leaks.
Ignite all burners both individually and concurrently to ensure
correct operation of gas valves, burners and ignition. Turn gas
taps to low position and observe stability of the flame for each
burner individually and all together.
Adhere the duplicate data plate to an accessible location near
to the cook top. When satisfied with the cook top, please
instruct the user on the correct method of operation. In case the
appliance fails to operate correctly after all checks have been
carried out, refer to the authorised service provider in your area.
S 70). Smooth
®