Dynabrade 10724 Manual - Página 4
Procurar online ou descarregar pdf Manual para Lixadeira Dynabrade 10724. Dynabrade 10724 4 páginas. 2-hand random orbital sander
Imprimir página3. Install the 98459 O-Ring onto the 56579 Valve Stem, apply a small amount of petroleum lubricant to the o-ring and insert the shortest portion (from the end to the o-ring)
of the valve stem assembly into the speed regulator.
4. Install the 56582 Safety Throttle Lever Assembly onto the housing and secure it in place with the 95627 Pin.
5. Install the 56598 Seal into the air inlet passage of the housing.
6. Install the 56586 Vacuum Plug into the exhaust passage of the housing. (See Exploded View)
7. Use needle-nose pliers to grasp and install the 51944 Tip Valve so that it fits under the 56579 Valve Stem.
8. Install the large end of the 51943 Spring into the air inlet passage of the handle.
9. Install the 56469 Gasket onto the mounting surface of the handle.
10. Apply a small amount of petroleum lubricant to the 96459 O-Ring and install it onto the outside diameter of the air inlet passage at the location of the first shoulder.
11. Connect the handle to the housing and secure it in place with the four screws. (Torque to 3 N•m/26 in.- lbs.)
Note: The two longer screws, Part Number 96454 (2) also secure the 13160 Grip to the housing.
12. Install the 56597 Muffler and secure it in place with the 56596 Muffler Clip. (See Exploded View)
Handle and Valve Assembly Complete. Tool Assembly Complete. Please allow 30 minutes for adhesives to cure before operating tool.
Important: Motor should now be tested for proper operation at 90 PSIG. If motor does not operate properly or operates at a higher RPM than marked on the tool, the tool should
be serviced to correct the cause before use. Before operating, place 2-3 drops of Dynabrade Air Lube (P/N 95842) directly into air inlet with throttle lever depressed. Operate tool
for 30 seconds to determine if tool is operating properly and to allow lubricating oils to properly penetrate motor.
Loctite
®
is a registered trademark of Loctite Corp.
Drawing 1
57091
Bearing Press Tool
56052 Bearing
Shaft Step
Bearing Seal and
Bearing Shield
Balancer Shaft
98220 Motor Tune-Up Kit
•
Includes assorted parts to
help maintain and repair motor.
96232 (#2) Arbor Press
•
This arbor press is ideal for the disassembly
and assembly of air motors.
96346 2" Bearing Separator
•
Use the separator to remove gears
and bearings.
Visit Our Web Site: www.dynabrade.com
DYNABRADE, INC., 8989 Sheridan Drive • Clarence, NY 14031-1490 • Phone: (716) 631-0100 • Fax: 716-631-2073 • International Fax: 716-631-2524
DYNABRADE EUROPE S.àr.l.,
© DYNABRADE, INC., 2004
Diagrams
Drawing 2
57091
Bearing Press Tool
02695 Bearing
Motor Shaft
Balancer
Balancer Shaft
Important: Lock Ring must now be placed
over sub-assembly. Not shown in drawings.
Optional Accessories
Zone Artisanale • L-5485 Wormeldange—Haut, Luxembourg • Telephone: 352 76 84 94 1 • Fax: 352 76 84 95 1
Drawing 3
57091
Bearing Press Tool
Front Bearing Plate
02695 Bearing
Motor Shaft
Balancer
Balancer Shaft
Dynabrade Air Lube
57260 Motor Repair Kit:
Email: [email protected]
Drawing 4
Bearing Press Tool
54629 Rear Bearing Plate
(with 01206 Bearing)
Line-Up Pin
Cylinder Assembly
(w/ rotor and vanes)
Front Bearing Plate
(with 02695 Bearing)
Motor Shaft Balancer
Balancer Shaft
•
Formulated for pneumatic equipment.
•
Absorbs up to 10% of its weight in water.
•
Prevents rust and formation of sludge.
•
Keeps pneumatic tools operating longer
with greater power and less down time.
95842: 1pt. (473 ml)
95843: 1gal. (3.8 L)
• Contains special tools for
disassembly/assembly of machine.
DYNABRADE
PRINTED IN USA
57091
®