ADELSYSTEM CB12245A Manual de instruções - Página 2

Procurar online ou descarregar pdf Manual de instruções para Carregador de bateria ADELSYSTEM CB12245A. ADELSYSTEM CB12245A 2 páginas. Smart battery charger

Imprimir página

Every time a battery will be connected to the Battery Charger, the device will do followings check: reverse battery

polarity, wrong battery connected (like batteries 24 – 36Vdc or higher) with Jumper n.5 not present = Battery charger

for 12Vdc. After 120 minutes, with jumper in pos. 5 present (24 Vdc output configuration) the device make the test of

wrong battery connected like batteries 12Vdc.

Every 240 minutes, make the test element in short circuit.

Diagnostic Type Checks:

Check for accidental disconnection of the battery cables:

The device detects accidental disconnection and immediately switched off the output power.

Battery not connected:

If the battery is not connected no output power.

Reverse Polarity check:

If the battery it is connected with inverted polarity, the device is automatically protected.

Test of battery voltage connections:

Appropriate voltage check, to prevent connection of wrong battery types, more or less than the nominal voltage.

End of Charge check

When the battery it is completely full, the device automatically switch in trickle charging mode.

Check for Battery Cells in short circuit

Thanks to specific algorithms of evaluation, the CBs recognize batteries with cells in internal short circuit.

In trickle charge every 4 hours test of element in short circuit.

Diagnosis of battery and device

All CB devices support the user during installation and operation. A Blink code of Diagnosis Led allows to

discriminate among various possible faults.

Error conditions, "LED Battery Fault" ON and "LED Diagnosis" blinking with sequence; see Display Signal section.

Protection Features

On the primary side: the device is equipped whit an internally fuse. If the internal fuse is activated, it is most probable

that there is a fault in the device. If happen, the device must be checked in the factory.

On the secondary side Battery and load: The device is electrically protected against short circuits and overload.

Inversion polarity: the module it is automatically protected against inversion of battery polarity and connection of load

inverted.

Over current and output short circuit: the unit limits the output current (see the technical data).

Thermal behaviour

Surrounding air temperature 50°C. For ambient temperature of over 50°C, the output current must be reduced by

2.5% per °C. Max 70°C At the temperature of 70°C the output current will be 50% of In. The equipment does not

switch off in case of ambient temperature above 70°C or thermal overload. The devices are protected for Over

temperature conditions "worst case"; in this situations the device Shut-down the output and automatic restart when

temperature inside fall.

Standards and Certification

Electrical Safety:

Assembling device: IEC/EN 60950 (VDE 0805) and EN 50178 (VDE 0160).

Installation according : IEC/EN 60950.

Input / Output separation : SELV EN 60950-1 and PELV EN 60204-1. Double or reinforced insulation.

EMC Standards Immunity :

EN 61000-4-2, EN 61000-4-3, EN 61000-4-4, EN 61000-4-5.

EMC Standards Emission:

EN 61000-6-4, EN 61000-6-3, EN 61000-3-2 (see data sheet for each device)

Standards Conformity:

Safety of Electrical Equipment Machines: EN 60204-1.

The CE mark in According to EMC 2004/108/EC and Low voltage directive 2006/95/EEC

In According to UL 1236 and CSA C22.2 N° 107.2

Norms and Certifications

In Conformity to: UL1236, IEC/EN 60335-2-29 Battery chargers; EN60950 / UL1950; Electrical safety EN54-4 Fire

Detection and fire alarm systems; 2014/30/UE Directive; 2014/35/UE (Low Voltage); DIN41773 (Charging cycle);

Emission: IEC 61000-6-4; Immunity: IEC 61000-6-2. CE.

Rail Mounting:

All modules must have a minimum vertical and horizontal distance of 10 cm to this power supply in

order to guarantee sufficient auto convection. Depending on the ambient temperature and load of the

device, the temperature of the housing can become very high!

Mounting Steps: 1, 2, 3, 4.

Removing Steps: 4, 3, 2, 1.

MOUNTING – REMOVING

Step 1

Step 3

Step 2

REMOVING

Step 4

-5°/+5° max

Technical Data:

Battery Charger

Multi Output voltage 12 – 24Vdc

Input (Volt)

Output (Vdc – A – W)

Model

INPUT DATA

Nominal Input Voltage / Tensione d'ingresso nominale

Input Voltage Range / Campo di funzionamento

Inrush Current (Vn and In Load) I

t / Corrente di Inserzione

Frequency /Frequenza di Ingresso

Input Current (115 – 230Vac) / Assorbimento

Internal Fuse / Fusibile Interno (non sostituibile)

External Fuse (recommended)/ Fusibile Esterno raccomandato

OUTPUT DATA

Output Vdc / I

/ Tensione di uscita Vdc / I

Minimum load / Carico minimo

Efficiency (50% of In) / Rendimento tipico

Short-circuit protection / Protezione contro il corto circuito

Over Load protection / Protezione sovraccarico

Over Voltage Output protection / Protezione sovratensione in uscita

Reverse battery protection / Protezione inversione batteria

Detection of element in short circuit / Rilevazione elemento in corto circuito

BATTERY CHARGER OUTPUT / USCITA CARICA BATTERIA

Boost – Bulk charge (Typ. at I

) / Carica Veloce (1)

Max.Time Boost–Bulk charge (Typ. at I

) / Tempo massimo Carica Veloce

Min.Time Boost–Bulk charge (Typ. at I

) / Tempo minimo Carica Veloce

Trickle-Float charge (Typ. at I

) / Carica di mantenimento (1)

Recovery Charge / Carica di recupero

Switching on after applying mains voltage

End of charging current Bulk - Absorption to Float - Trickle

Start up with capacitive load / Start up con carichi capacitivi

Residual Ripple / Ripple Residuo

Charging max I

/ Corrente max. di Carica

batt

Charging current Limiting I

) / Limitazione Corrente di Carica

adj

Quiescent Current / Consumo da batteria max.

JUMPER CONFIGURATION

Battery Type / Tipo Batteria VRLA

------------------------------------------Ni-Cd option

Battery Voltage 12 or 24 Vdc / Selezione Tensione di Batteria 12 o 24 Vdc

Power Supply Function / Funzione Alimentatore

Boost Charge Enable / Abilitazione Carica Rapida

Characteristic Curve / Caratteristiche di Carica

SIGNAL OUTPUT (RELAY) / SEGNALAZIONE RELÈ USCITA

Main or Backup Power

Low Battery and Fault Battery

Main or Backup - Fault Battery

AUXILIARY OUTPUT (RJ 45 CONNECTION) FOR:

Temp. Charging probe / Carica Compensata in Temperatura

Voltage drop compensation / Comp. Tensione di ricarica

Remote monitoring display / Display Esterno

CLIMATIC DATA

Ambient Temperature operation / Temperatura Ambiente di Lavoro

De rating Tª > (In) / De rating Tª > (In)

Automatic De rating / De rating Automatico

Ambient Temperature Storage / Temperatura max. Magazzino

Humidity at 25 °C / Umidità

Cooling / Raffreddamento

GENERAL DATA

Isolation Voltage (IN / OUT) / Tensione di Isolamento (IN / OUT)

Isolation Voltage(IN / PE) / Tensione di Isolamento(IN / TERRA)

Isolation Voltage(OUT / PE) / Tensione di Isolamento(OUT/TERRA)

Protection Class (EN/IEC 60529) / Protezione Classe

Reliability (MTBF IEC 61709) / Affidabilità

Pollution Degree Environment / Grado d'inquinamento ambientale

Connection Terminal Blocks Screw Type / Dimensione morsetti

Protection class (with PE connected) /

Grado di protezione (con cavo di terra collegato)

Dimension (w-h-d)/Dimensioni (l-h-p) mm

Weight / Peso

Safety Standard Approval / Conformità ed Approvazioni

CONNECTION DIAGRAM / SCHEMA DI CONNESSIONE

(1) - Depend on jumper selection

All specification are subject to change without notice

115 – 230 – 277Vac

12Vdc – 6A – 120W

24Vdc – 5A – 120W

CB12245A

115 – 230 – 277Vac

90 – 305Vac

≤ 16 A ≤ 5msec

47 – 63 Hz ±6%

2.4 – 1.2A

10A (MCB curve B)

12Vdc – 6A

24Vdc – 5A (230Vac)

24Vdc – 4A (120Vac)

≥ 90%

Yes

14.4Vdc (12Vdc)

28.8Vdc (24Vdc)

15h

4 min.

13.75Vdc (12Vdc)

27.50Vdc (24Vdc)

3 – 8 Vdc (12Vdc)

6 – 18 Vdc (24Vdc)

2.5sec

1/8 of Iadj

≤ 30.000µF

≤ 80 mVpp

6A ± 5% (12Vdc)

5A ± 5% (24Vdc) Ta < 40°C (In)

3.5A ± 5% (24Vdc) Ta > 40°C (In)

Yes, 10 ÷ 100 % / In

≤5mA

--------------

2.23;2,25;2,27;2,3;

1,4–1,5 (20 elem.)

Yes

IUoUo

Yes

-25 – +70°C

> 50° 2.5% °C

Yes

-40 – +85°C

95% to 25°C

Auto Convection

3000Vac

1605Vac

500Vac

IP 20

> 300 000 h

2,5mm(24–14AWG)

I, with PE connected

45x105x100 mm

0.30 kg approx