Hi-ltte RAMBO330 3in1 Series Manual do utilizador - Página 6

Procurar online ou descarregar pdf Manual do utilizador para Luminária Hi-ltte RAMBO330 3in1 Series. Hi-ltte RAMBO330 3in1 Series 9 páginas. 330w 3in1 beam-spot wash

Imprimir página

INSTALLATION

Note: Lights be placed vertically upward,the shortest distance between

working lights must be more than or equal 900mm, lighting installation

layout as following

900mm

5.3

Data cable

Data cable is DMX512 signal

Note: Signal line connections is X-type connector。

X-type connector-----If the external flexible cable or cord

of thislight is damaged, please replace professional cable

or cord from the manufacture or its agent.Lights' DMX

input and output connects to a three-pin

XLR and five-pin XLR insert, first pin is grounded,

then negative signal is

second pin, third pin

connects to the positive

polarity signal, fourth and

fifth are empty.In order to

prevent reception reflection and

3XLR plug

Terminal plug connect with XLR

interference control signal,

1.Grounding

plug second or third by a 0.25w

2.Signal-

120ohm resistor, then connect

a terminal plug must be installed

3.Signal+

the resistor into last light's DMX

output jack

on the first branch of the connected

device last 3-pin output jack.

controller is connects to the nearest input XLR 3-pin, then from

the output of the device connects to the input of the next device,

continuous connection one by one, the final output data cable

terminal equipment plug one end into the terminal.

If the signal transmission is long-distance , 512 signal amplifier

must be added. DMX512 signal controller connect to the input of

the amplifier first, then connect to the fixture from its output,

couple with the terminal plug last.

1 Do not use two separate output connection, if connec

t the branch separating consecutive DMX512 signal

amplifier must be used to separate.

2 Please use the shielded twisted-pair cable,

standard microphone cable can not be reliably

controlled long-distance data.

6.Fuse Size

Power :100-240v

Fuse: 8A 5 * 20 main fuse

6.2 Power Connection

If the external flexible cable or cord of this light is damaged, the

line is up to the manufacturer or its service agent or a similar

qualified person to replace, in order to avoid danger. Connect

the power supply personnel must have the appropriate

qualifications before proceeding, you must make sure you are

using the power supply voltage matches the voltage identified

and have overload or leakage protection. Directly connect the

device to the power supply, do not connect to the silicon box

dimming system, otherwise damage to the equipment.

Note:

1 Do not install other similar bulbs, otherwise it will produce safety hazards or

equipment damage.

2.To reduce the risk of damage to the light, replacing the lampbefore its life is over

3.Mustn't use the banned scratched and damaged bulb

7.1 Lamp Description

RAMBO330w 3in1 moving head beam light is used with Yodn

Single-ended lamp is short arc point light source, and its color

temperature is 8000K and very stable, CRI

＞

90.Life span is over

2000 hours(according the using situation)

Attention

1.1. Do not install other similar lamps, and will cause safety

hazards or equipment damage.

2.To reduce the risk of damage to the lamp, replacing the

lamp before the lamp life over.

3. Do not use scratches and has damaged bulb

AC POWER

7.2 Changing lamp

1 Disconnect the power, so that the lamp cooling, the arm

of the lamp body lock locked in a horizontal position.

2 split bulbs:Remove thecover which is written "split this

cover to replace the lamp head cover"

3 Use a Phillips screwdriver to remove the fan two thumbscrews

fixed side.

4 with the appropriate force to push down the bulb when the

lamp cup beyond the edge of the

stainless steel shrapnel, taking up the lamp.

5 Install the bulb is the opposite of the operation.

Note: when replacing a lightlamp does not touch the bulb with

bare hands at the ball, avoiding oil stained hands on the ball.

2 When you install and dismantle the lamp into the lamp gently

put on, can not let the bulb hit hard objects around it to prevent

damage the bulbs.

7.3 Correction bulbs

(lamp has been corrected before selling, if the individual case

happens when changing the lamp, could following this way. the

light is reseted by turning on the power,using the menu or console

light bulb to play a bunch of white beam.

2 Using Phillips screwdriver to open the light body one bonnet side

which is printed "this cover to replace the lamp"

3 Using a flathead screwdriver to adjust the lamp bracket adjustment

screw, turn the screw clockwise or counter clockwise, and the

lamp can be right or left to adjust.