Dynabrade 10746 Segurança, operação e manutenção - Página 6
Procurar online ou descarregar pdf Segurança, operação e manutenção para Moedor Dynabrade 10746. Dynabrade 10746 8 páginas. 5" random orbital buffer
Imprimir página
3. Install the 98459 O-Ring onto the 56579 Valve Stem, apply a small amount of petroleum lubricant to the o-ring and insert the shortest portion (from the end to the o-ring)
of the valve stem assembly into the speed regulator.
4. Install the 56582 Safety Throttle Lever Assembly onto the housing and secure it in place with the 95627 Pin.
5. Install the 56598 Seal into the air inlet passage of the housing.
6. Install the 51368 Felt Silencer, 51369 Muffler Disc and 51373 Muffler Clip into the exhaust passage of the housing. (See Exploded View)
7. Use needle-nose pliers to grasp and install the 51944 Tip Valve so that it fits under the 56579 Valve Stem.
8. Install the large end of the 51943 Spring into the air inlet passage of the handle.
9. Install the 56469 Gasket onto the mounting surface of the handle.
10. Apply a small amount of petroleum lubricant to the 96459 O-Ring and install it onto the outside diameter of the air inlet passage at the location of the first shoulder.
11. Connect the handle to the housing and secure it in place with the four screws. (Torque to 3 N•m/26 in.- lbs.)
Note: The two longer screws, Part Number 96454 (2) also secure the 13160 Grip to the housing.
12. Install 51372 Seal and 56597 Muffler, secure it in place with the 56596 Muffler Clip. (See Exploded View)
Handle and Valve Assembly Complete. Tool Assembly Complete. Please allow 30 minutes for adhesives to cure before operating tool.
Important: Motor should now be tested for proper operation at 90 PSIG. If motor does not operate properly or operates at a higher RPM than marked on the tool, the tool should
be serviced to correct the cause before use. Before operating, place 2-3 drops of Dynabrade Air Lube (P/N 95842) directly into air inlet with throttle lever depressed. Operate tool
for 30 seconds to determine if tool is operating properly and to allow lubricating oils to properly penetrate motor.
Loctite
®
is a registered trademark of Loctite Corp.
Drawing 1
57091
Bearing Press Tool
56052 Bearing
Shaft Step
Bearing Seal and
Bearing Shield
Balancer Shaft
96232 (#2) Arbor Press
•
This arbor press is ideal for the disassembly
and assembly of air motors.
96346 2" Bearing Separator
•
Use the separator to remove gears
and bearings.
96343 Retaining Ring Pliers
•
Drawing 2
Bearing Press Tool
02695 Bearing
Motor Shaft
Balancer Shaft
Important: Lock Ring must now be placed
over sub-assembly. Not shown in drawings.
Special Repair Tools
Internal/external retaining ring pliers.
Tip diameter - 0.038" (0.96mm)
Diagrams
Drawing 3
57091
Bearing Press Tool
Front Bearing Plate
Balancer
6
Drawing 4
54629 Rear Bearing Plate
57091
02695 Bearing
Motor Shaft
Balancer
Balancer Shaft
96405 Motor Repair Kit:
• Contains special tools for
disassembly/assembly of machine.
96213 Bearing Removal Tool
•
This tool is used to pass through the I.D.
of the bearing plate and to push against
the I.D. of the bearing.
57091 Bearing Press Tool
•
This tool is used to install press-fit bearings.
57091
Bearing Press Tool
(with 01206 Bearing)
Line-Up Pin
Cylinder Assembly
(w/ rotor and vanes)
Front Bearing Plate
(with 02695 Bearing)
Motor Shaft Balancer
Balancer Shaft