2gig Technologies 2GIG-SHKDW1-345 Instruções de instalação

Procurar online ou descarregar pdf Instruções de instalação para Acessórios 2gig Technologies 2GIG-SHKDW1-345. 2gig Technologies 2GIG-SHKDW1-345 4 páginas. Shock/door/window contact sensor

Imprimir página

INSTALL INSTRUCTIONS SHOCK/DOOR / WINDOW CONTACT 2GIG-SHKDW1-345 - P/N: 10021991 X8 - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 11" x 17" (8.5"+8.5") COVER: PRINT 1ST AND 4TH PAGES / INSIDE: PRINT 2ND

2GIG-SHKDW1-345

Shock/Door/Window Contact Sensor

INSTALLATION INSTRUCTIONS

The Shock/Door/Window Contact Sensor (2GIG-SHKDW1-345) is

designed for use on doors, windows, and other objects that open

and close. It communicates with the control panel using the 345 MHz

frequency. When the surface it is mounted on is struck with sufficient

force, signals are sent to the control panel. Additionally, when the

magnet (which is mounted near the sensor) moves away from or

closer to the door contact's sensor, signals are transmitted to the

control panel. For added protection, it is also equipped with a cover

and magnetic tamper detection.

Magnetic Tamper Detection

The 2GIG Shock/Door/Window Contact Sensor is equipped with

Magnetic Tamper Detection. When enabled (see Enable / Disable

Magnet Detection) the device can detect if a foreign magnet is brought

within it's detection range. This will trigger a Tamper alert to the control

panel indicating a possible attempt to bypass the device.

If this were to occur, the device will stop transmitting and a Loss of

Supervision will be noted at the control panel. To clear this event, the

Shock/Door/Window Contact Sensor will need to be re-calibrated (see

Calibrating Magnet Detection).

Figure 1. Shock/Door/Window Contact Sensor and Magnet

Shock/Door/Window Contact Sensor

Magnet alignment Marks on Sensor

Shock/Door/Window Contact Magnet

Box Contents

Verify that the package includes the following:

●

1 — Shock/Door/Window Contact Sensor

●

1 — Rare Earth Magnet

●

2 — Phillips Head Mounting Screws

●

1 — Lithium Coin Battery (Installed)

●

2 — Adhesive Foam Tape (pre-applied on sensor and magnet)

●

1 — Window Warning Sticker

Testing The Shock/Door/Window Contact Sensor

Before mounting the contact at the desired location, learn it into the

control panel. Then, perform a walk test utilizing a shock event as the

test transmission to verify that it can establish good Radio Frequency

(RF) communications with the control panel.

NOTE: To learn how to program and fully test the Shock/Door/Window

Contact Sensor, see the control panel's Installation and Programming

Guide. For 2GIG panels using older irmware, this sensor may be

learned in as a D/W device. Newer panel firmwares will support

shock detector equipment code type 1066.

Mounting Guidelines

Use these guidelines when installing the sensor:

● Mount Sensors within 100 ft (30 m) of the Control Panel.

Although the transmitter may have a range of over 500 ft (150m)

open air, the sensor location can have a significant effect on

range. In open/unobstructed situations, the transmitter range may

be greater. In adverse wireless conditions, changing the sensor

orientation may lead to improved range.

AND 3RD PAGES - TOL: +/- 0.125"- SCALE: 1-1 - FOLDING: TO FIT BOX - FINISH WITH PAGE 1 LOGO SHOWING - SIDE 1 OF 2

PRINTER'S INSTRUCTIONS

● Mount Sensors at Least 4.7 in (12 cm) Above the Floor. Placing

sensors slightly above floor level helps to minimize possible sensor

damage.

● Window Shock and Sliding Door/Window Installation: Mount

the Shock/Door/Window Contact Sensor on the fixed pane window

1" from the frame for optimal performance. Place the sensor on the

moving section of the door/window and the magnet in a stationary

location. The included magnet must be within 2" of the sensor. If a

wider gap is required, up to 5", use the optional DecoTrim Magnet

(p/n 2GIG-DECOTRIM).

● Do Not Expose Sensors to Moisture or Extreme Temperature.

It is best to mount sensors in a dry location where the operating

temperature does not exceed 0° to 130°F (-18° to 54°C).

● Keep Sensors and Magnets Away from Metal/Metallic

Surfaces. Keep sensors and magnets away from metal or metallic

surfaces (for example, foil). You should also avoid mounting

sensors in areas where there is a large quantity of metal or

electrical wiring (for example, near a furnace or in a utility room).

NOTE: Use on metal doors and windows with metal frames will

significantly impair the performance of this sensor.

Mounting The Shock/Door/Window Contact Sensor

Use the figure below as a guideline when mounting the contact.

Figure 2. Backplate and Battery Compartment

Screw mounting holes

(on backplate)

Programming Button

CR2450 Lithium battery

(under circuit board)

Battery Access Slot

Figure 3. Standard Glass Mounting

Sensor

To mount the Shock/Door/Window Contact Sensor:

Remove the backing form the pre-applied double-sided tape on the

bottom of the Sensor and place in the desired location.

NOTE: When mounting on a glass window, place the device one

inch from the top or bottom and side edge of the window.

Under Circuit Board

1 to 2"

Magnet

Sensor: Install one inch

from the edge of the glass.

Magnet: Install 1 to 2

inches from the Sensor.