GREAT PLANES EP YAK 55 3D ARF Manual de instruções - Página 3
Procurar online ou descarregar pdf Manual de instruções para Brinquedo GREAT PLANES EP YAK 55 3D ARF. GREAT PLANES EP YAK 55 3D ARF 16 páginas.
Imprimir página
the instructions may differ slightly from the photos. In those
instances the written instructions should be considered
as correct.
3. You must take time to build straight, true and strong.
4. You must use an R/C radio system that is in first-class
condition, and a correctly sized motor and components
throughout the building process.
5. You must correctly install all R/C and other components
so that the model operates correctly on the ground and in
the air.
6. You must check the operation of the model before every
flight to insure that all equipment is operating and that the
model has remained structurally sound. Be sure to check
clevises or other connectors often and replace them if they
show any signs of wear or fatigue.
7. If you are not an experienced pilot or have not flown this
type of model before, we recommend that you get the
assistance of an experienced pilot in your R/C club for your
first flights. If you're not a member of a club, your local
hobby shop has information about clubs in your area whose
membership includes experienced pilots.
8. While this kit has been flight tested to exceed normal use, if
the plane will be used for extremely high-stress flying, such as
racing, or if a motor larger than one in the recommended
range is used, the modeler is responsible for taking steps to
reinforce the high-stress points and/or substituting hardware
more suitable for the increased stress.
We, as the kit manufacturer, provide you with a top
quality, thoroughly tested kit and instructions, but
ultimately the quality and flyability of your finished model
depends on how you build it; therefore, we cannot in any
way guarantee the performance of your completed
model, and no representations are expressed or implied
as to the performance or safety of your completed model.
Remember: Take your time and follow the instructions to
end up with a well-built model that is straight and true.
LITHIUM BATTERY HANDLING
& USAGE
WARNING!! Read the entire instruction sheet included with
this battery. Failure to follow all instructions could cause
permanent damage to the battery and its surroundings, and
cause bodily harm!
• ONLY use a Li-Po approved charger. NEVER use a
NiCd/NiMH peak charger!
• NEVER charge in excess of 4.20V per cell.
• ONLY charge through the "charge" lead. NEVER charge
through the "discharge" lead.
• NEVER charge at currents greater than 1C.
• ALWAYS set charger's output volts to match battery volts.
• ALWAYS charge in a fireproof location.
• NEVER trickle charge.
• NEVER allow the battery temperature to exceed
150°F (65°C).
• NEVER disassemble or modify pack wiring in any way or
puncture cells.
• NEVER discharge below 2.5V per cell.
• NEVER place on combustible materials or leave
unattended during charge or discharge.
• ALWAYS KEEP OUT OF REACH OF CHILDREN.
ADDITIONAL ITEMS REQUIRED
Radio Equipment & Electronics
(Note:
Recommended
in parentheses)
4-Channel radio
3 Sub-micro servos (0.3 oz [9g] or less each) (FUTM0042)
Micro receiver (FUTL0442-3)
6" Servo extension (HCAM2000)
12" Servo extension (HCAM2100)
20-amp Brushed ESC (GPMP2020)
1200–1500mAh 3-series Lithium Polymer battery pack
(GPMP0821, GPMP0831)
Deans Ultra Male plug (WSDM1302)
Lithium-Polymer Charger (GPMP3150, GPMP3010)
Adhesives & Building Supplies
In addition to common household tools and hobby tools, this
is the "short list" of the most important items required to
build the YAK 55 ARF. Great Planes Pro
glue are recommended.
6-minute Epoxy and/or foam safe CA
60/40 Tin/lead solder
Soldering iron
Covering iron (or household iron)
Hobby knife with #11 blade
Optional Supplies & Tools
Here is a list of optional tools mentioned in the manual that
will help you build the YAK 55 ARF.
Great Planes C.G. Machine
3
part
numbers
are
™
CA and Epoxy
™
include