GREAT PLANES MASTER CADDY Manual de instruções de montagem - Página 15
Procurar online ou descarregar pdf Manual de instruções de montagem para Instrumentos de medição GREAT PLANES MASTER CADDY. GREAT PLANES MASTER CADDY 15 páginas. With auxiliary power station
Imprimir página
up the curing. Install the cradle assemblies on the MAS-
TER CADDY.
Slide the 4-1/2" long pieces onto the
cradles as shown above and glue only one side of the
foam to one of the cradles. The other cradle has to be
free to slide under the foam tube.
O 3. Cut the Velcro strip in half and separate the
pieces. Peel the backing off one piece and stick it firmly
on the back of the bottom drawer.
Gently touch the
Opposite piece of Velcro to the piece on the back of the
drawer, but put a scrap of paper between the two pieces
so that it covers approximately 3/4 of the surfaces. This
will help the second Velcro piece stick to the caddy. Peel
the backing off of the second piece of Velcro and slide the
drawerintoits slot. Push the drawer against its stops and
then gently pull the drawer out. The Velcro should have
stuck to the caddy, If it did not, manually stick it on the
caddy by estimating where it should be and pressing it in
place. In either case, when you have it properly posi-
tioned, firmly press it in place. The adhesive used on the
Velcro will hold more strongly with time. If the Velcro
does not catch when the drawer is in place, you can add
a shim between the Velcro and the Drawer Back to help
the Velcro grab.
NOTE - If you would like to keep your newly
finished MASTER CADDY from sitting directly on the
ground we suggest the addition of small plastic or rubber
feet which are available at your local hardware store.
This completes the assembly
of your
GREAT
PLANES
MASTER CADDY.
We hope
your building experience was
enjoyable .
GOOD LUCK
and
HAPPY FLYING!
15
PARTS LIST
STOCK # QTY.
DESCRIPTION
DOWEL028
1
3/4" X 11-1/6" Dowel Handle
DOWEL029
1
1/2" X 3-13/16" Dowel APS Handle
FOAM007
1
Foam Cradle Cushion
GPB2F01
1
9mm Plywood Side A
GPB2F02
1
9mm Plywood Side C
GPB2F03
1
9mm Plywood Bottom
GPB2F04
2
9mm Plywood Upright
GPB2F0S
1
5.2mm Plywood Shelf
GPB2F06
1
5.2mm Plywood Shelf Divider A
GPB2F08
2
5.2mm Plywood Drawer Bottom
GPB2F09
2
5.2mm Plywood Drawer Front
GPB2F10
2
5.2mm Plywood Drawer Back
GPB2F11
2
5.2mm Plywood Drawer Divider
GPB2F12
5
5.2mm Ply Drawer Side & Divider B
GPB2F13
2
9mm Plywood Gusset
GPB2F14
1
9mm Plywood Side B
GPB2T14
1
5.2mm Plywood APS Shelf
GPB2T15
1
5.2mm Plywood APS Upright A
GPB2T16
1 5.2mm Plywood APS Upright B
GPB2T17
1
5.2mm Plywood APS Front
GPB2T18
1
5.2mm Plywood APS Bottom
GPB2T19
1
3mm Plywood APS Side B
GPB2T20
1
3mm Plywood APS Side A
GPB2T21
2
8" Beveled Basswood Strip
GPB2T22
6
3/8" SQ. X 1" Basswood Block
GPB2T23
2
1/4" SQ. Drawer Support
GPB2H25
4
1/8" Plywood Die-Cut Cradles
NYLONS!
1
Nylon Strip
GPB2P01
1
Instruction Book
B2M01
1
B-PACK
WARE
KNOBSOL
2
Wooden Drawer Knob
NUTSOI7
2
10-24 Stamped Wing Nut
SCRW043
12 #4 X 3/8" Slotted Screw
SCRW049
2
10-24 X 1-1/4" Bolt
SCRW050
2
#10 X 5/8" Slotted Screw
SCRW054
2
#8 X 5/8" Phillips Head Screw
VELCRHOI
1
VELCRO Hooks Strip 3"
VELCRLO1
1
VELCRO Loops Strip 3"
WSHROOS
4
#4 Flat Washer
WSHR009
2
#10 Flat Washer
If any parts are missing, broken or defective,
or if you have any questions about building this
kit, please call us at (217) 398-8970and we will
be glad to help. If you are calling for replacement
parts, please look up the part numbers and the kit
identification number (stamped on the end of the
carton) and have them ready when calling.