Automatic Mirage M 801E Manual - Página 17

Procurar online ou descarregar pdf Manual para Amplificador Automatic Mirage M 801E. Automatic Mirage M 801E 17 páginas. Multi-zone digital amplifi er manual

Imprimir página

Notes

• Commands are used as notifications. If an

amplifier is switched ON, it will notify the

other devices on the Control Bus by sending

the Standby command (01). Any amplifiers

with the same zone will take the notifica-

tion as a command and also switch ON.

• When a command is sent to an amplifier

it will first be transmitted on the control

bus and then returned to the PC (Home

Automation System). If an error occurs

an error will be returned instead of the

original command. The PC (Home Automa-

tion System) needs to ignore its command

when it is returned.

• A Standby ON command implies that the

amplifier is not muted, if the amplifier was

previously Off, a mute command must fol-

low the Standby command if it is muted.

• Not all Command and Data commands are

covered in this document.

• The expected reply for the "Send all

Parameters" command (09) is >144 bytes.

All command fields listed in this document

are contained in the reply. The reply also

contains advanced commands not listed

in this document. The home Automation

or PC's buffer should be large enough to

receive and process the 144-byte reply.

a. Zone 2 links to Zone 3.

b. Since Zone 2 is no longer linked to

Zone 1, Zone 1 will no longer be

linked to Zone 2.

c. Since Zone 3 is no longer linked to

zone 4, Zone 4 will no longer be

linked to Zone 3.

Example strings:

• 010A01: Standby ON command for Zone

10 amplifier.

• 012A01: Standby ON command for Zone

10 preamplifier.

• 060002: +2db Treble setting on Zone 0.

• 03IF02: Select Source 7 on Zone 31.

Specifications

Rated Output Power (FTC)

All Channels

Total Harmonic

Distortion (THD)

Speaker Impedance

(Z1 - Z6 L/R)

Input Sensitivity and

Impedance (S1 - S6 L/R)

Coax digital input level

and impedance

Pre Amplifier Output Level and

Impedance (Z7 & Z8 L/R)

Frequency Response

Tone Control

Signal to Noise Ratio

IR Output

Source Inputs

Ethernet

USB

Data

Controllers

Zone Triggers & Presets

Power Supply

Power Consumption

Standby Power Consumption

Dimensions with feet

Dimensions without feet

Weight

Touch Panel Display

Zones

A digital copy of this manual can be found at:

http://www.autonomic-controls.com/support_documentation.php

All other trademarks are property of their respective owners. Specifications are based on current revision and may change without notice. 082516

M·801e

50W per channel (100W per zone), 8Ω loads

0.1% (40 Watt, 8 Ω load)

4Ω–8Ω

0.72V / 22KΩ (Unbalanced)

0.5V ± 0.05V / 75 Ω

+16dB / 470 Ω

20Hz - 20 KHz ± 3dB (8 Ω)

±12dB, 100Hz (Bass) ±12dB, 10kHz (Treble)

100dB (IHA-A, 1V input / unbalanced)

(8) 3.5mm Jack: IR1 - IR8 current limited to 25mA

(8) Digital Coaxial RCA, (6) Analog (L/R) RCA, (2) TOSLINK

(1) Shielded RJ45 socket, 100Base-T

(1) USB mini-B female 5 pin

(1) 4 pole 3.5 mm terminal block connector (Data,12V, IR,0V)

(8) RJ45 sockets Keypad controller ports

(1) 12 pole 3.5 mm terminal block connector

(Zone trigger 0V out, Zone trigger 1 - 8 12V out, Common, Preset 1 - 2 in)

110–240V AC 50–60Hz

650W

4.0" H x 17" W x 15" D (10.2cm x 43.2cm x 38.1cm)

3.5" H (8.9cm); fits 2RU

16.3 lb. (7.4 kg)

2.4" color LCD touch panel display for menu guided control and programming.

(8) zones

Expandable to 96 zones, attaching additional M-801e or M-401e amplifiers