Daytona 98437 Manual de instruções - Página 4
Procurar online ou descarregar pdf Manual de instruções para Acessórios para motociclos Daytona 98437. Daytona 98437 4 páginas. Slim-mount usb
Imprimir página21. Connect the cable to the negative battery terminal. Use a tester to identify the location where the – battery cable (ground) is
connected to the vehicle with an M6 or smaller bolt. After identifying the ground, disconnect the cable from the negative battery
terminal.
※ The location of the – battery cable (ground) is where the resistance is nearly 0 Ω.
22. Fasten both the – wire (black) of the USB power supply body ① and the – battery cable (ground) identified in step 21 with the bolt.
23. Use a cable tie ⑨ to secure the transformer ③ to the vehicle.
24. Connect the cable that was disconnected before performing the work to the negative battery terminal.
25. Install any vehicle parts that were removed before performing the work.
26. Turn the handlebar to the left and right to check that the fuse holder wires are not pulled and that no parts come into contact with
the product.
※ A pulled wire can lead to problems such as sudden operation failure.
27. Check that there are no abnormalities; if there are no problems, the work is completed.
【 Troubleshooting 】
Symptom
Cause
No power is supplied.
There is improper contact
with wires of other parts.
A wire of a part or the USB
cable is bent at a sharp angle.
The fuse blows.
Not charging
The rated capacity of
the output is exceeded.
A wrong type of USB cable
is used.
The USB cable is damaged.
There is improper contact
at the USB port.
The transformer is exposed
to interference.
There is improper contact
with wires of other parts.
The fuse holder wires are
subjected to strong tension.
The voltage drops when
the engine is started.
Charging may
The transformer
stop.
becomes hot.
The USB cable is damaged.
There is improper contact
at the USB port.
The transformer is
exposed to interference.
The charging
The connected electronic
device is hot.
indicator is on,
but the charge
A wire of a part or the USB
does not
cable is bent at a sharp angle.
increase
The transformer
or decrease.
becomes hot.
The power supply wire is
The battery charge
drops quickly
connected to an unswitched
during long-term
wire.
storage.
Solution
Make sure that 12 V DC is supplied at the + wire connection.
Make sure that the – wire is connected to the ground.
Check the wire connections of each part.
If a wire or cable is held in place bent at a sharp angle, the electric current may not flow correctly.
Reroute the wire to provide sufficient slack.
Make sure that the power supply wires are not reversed.
If the fuse blows immediately after being replaced, the main unit may be damaged.
Gather your purchase information and consult your retailer.
In rare cases, the fuse may blow if the product is supplied with high-voltage power. Consult with
the vehicle retailer to make sure that there are no problems with the electrical system of the vehicle.
The capacity is maximum 12 W (5 V, 2.4 A) for each port. Check the rating of your electronic devices.
※If the output rating is exceeded, the power will be cut.
Certain mobile phones may not charge unless a communication cable is used. Check the USB cable.
Make sure that the USB cable is not damaged.
Make sure that there is no improper contact at the USB port or in the USB connection with the connected
device.
Is the transformer installed near a noise-generating part? The transformer may be malfunctioning due to
interference. Take measures against noise such as changing the installation location of the transformer
or wrapping it with aluminum tape that is grounded.
Check the wire connections of each part for improper contact.
Make sure that the fuse holder wires are not pulled when the handlebar is operated or while riding.
In case of tension, reroute the wire.
Certain mobile phones may interpret the voltage drop that occurs when the engine is started to be
abnormal and stop charging. Connect the electronic device to the USB port after starting the engine.
If the transformer is installed near a heat-generating source, the operating temperature will be exceeded
and output may stop. Change the installation location of the transformer.
Make sure that the USB cable is not damaged.
Make sure that there is no improper contact at the USB port or in the USB connection with the connected
device.
Is the transformer installed near a noise-generating part? The transformer may be malfunctioning due to
interference. Take measures against noise such as changing the installation location of the transformer
or wrapping it with aluminum tape that is grounded.
Is your electronic device abnormally hot? If software is used at the same time that the device is being
charged, a protection function on some devices may be activated to reduce the charging current.
Temporarily stop using the device. ※This is likely to occur when the electronic device is used in
midsummer and exposed to direct sunlight.
If a wire or cable is held in place bent at a sharp angle, the electric current may not flow correctly.
Reroute the wire to provide sufficient slack.
If the transformer is installed near a heat-generating source, the operating temperature will be exceeded
and output may stop. Change the installation location of the transformer.
This product consumes a small amount of standby power, even when no electronic device is connected to
a USB port. The consumption is small, but battery depletion will be faster than usual if the battery is weak
or during long-term storage. Connect the + wire to the wire that carries 12 V when the ignition key is
turned on.
4/4