2gig Technologies pir1-345 Instruções de instalação

Procurar online ou descarregar pdf Instruções de instalação para Sensores de segurança 2gig Technologies pir1-345. 2gig Technologies pir1-345 4 páginas. Passive infrared motion detector

Imprimir página

2gig Technologies pir1-345 Instruções de instalação

2GIG-PIR1-345

PASSIVE INFRARED MOTION DETECTOR

INSTALLATION INSTRUCTIONS

The Passive Infrared Motion Detector (2GIG‐PIR1‐345) is a wall‐

mounted unit with wide‐angle motion protection. It communicates

with the 2GIG Control Panel using the 345 MHz frequency. When set

to High (HI) Sensitivity Mode, the PIR has a maximum range of 30 ft

deep x 50 ft wide (9.1 m x 15.2 m). The PIR's pet‐immune feature can

be set to tolerate animals up 55 lbs.

Figure 1 Passive Infrared Motion Detector

Box Contents

Verify that the package includes the following (see Figure 3 PIR and

Mounting Bracket Detail on page 2):

• 1—Passive Infrared Motion Detector (Part A)

• 1—Plastic Mounting Bracket (Part B)

• 1—Plastic Wall Mount (Part C)

• 1—Plastic Corner Mount (Part D)

• 2—Plastic Wall Anchors With Screws (not pictured)

• 1—Short Phillips Head Screw with Fender (not pictured)

• 1—Short Phillips Head Screw (not pictured)

• 1—Lithium Coin Battery (not pictured)

Inserting and Replacing the Battery

To insert or replace the battery:

Unwrap the PIR and remove the screw from the case bottom.

Remove the backplate using a bottom‐to‐top lifting motion.

Insert the battery.

Always match the plus (+) sign on the battery with the flat side of

the compartment and the minus (‐) sign on the battery with the

spring side.

Replace the PIR cover.

WARNING:

Failure to follow these warnings and instructions can

lead to heat generation, rupture, leakage, explosion, fire, or

other injury, or damage. Do not insert the battery into the

compartment in the wrong direction. Always replace the

battery with the same or equivalent type (see Specifications

on page 4). Never recharge or disassemble the battery. Never

place the battery in fire or water. Always keep batteries away

from small children. If batteries are swallowed, promptly see

a doctor.

• Always dispose and/or recycle used batteries in accordance with

the hazardous waste recovery and recycling regulations for your

location. Your city, state, or country may also require you to

comply with additional handling, recycling, and disposal

requirements.

Configuring the PIR Features

Ensure that you have inserted the PIR battery as described in Inserting

and Replacing the Battery. Then configure the features as follows:

Figure 2 PIR Pet Immune and Sensitivity Features

A PET: This is the pet‐immune tolerance setting (33 LBS or 55 LBS).

B TAMPER: This is the tamper switch.

C SENS: This is the sensitivity setting (High or Low).

Step 1: Setting the Pet Immune Feature

To set the pet immune feature to an appropriate weight:

NOTE:

Do not aim the PIR at stairs, furniture, or other surfaces

that a pet may climb on. The PIR provides immunity when the

room temperature is above 50° F (10° C) and below 90° F (32°

C). When mounting the PIR with the plastic mounting bracket,

for best protection ensure the PIR is mounted to the wall or

corner with NO tilt (see Lens Pattern and Tilt Angles on

page 3).

With the backplate off, locate the left jumper block immediately

above the battery compartment. This is the block labeled PET (see

Figure 2 PIR Pet Immune and Sensitivity Features).

Gently pull out the jumper and slip it over the desired pins to set

one of the pet‐immune tolerance settings:

• 33 LBS. Tolerates pets up to 33 lbs (15 kg).

• 55 LBS (Default). Tolerates pets up to 55 lbs (25 kg).

Continue with the next step below.

Step 2: Setting the Sensitivity Feature

Locate the right jumper block immediately above the battery

compartment on the right. This is the block labeled SENS (see

Figure 2 PIR Pet Immune and Sensitivity Features).

Gently pull out the jumper and slip it over the desired pins to set

the desired sensitivity mode:

• LOW (Default). Low sensitivity. This is the recommended

setting for pets.

• HIGH. High sensitivity.

Continue with Step 3: Powering ON the PIR on page 2.