Dynamite Prophet Precept Manual de instruções

Procurar online ou descarregar pdf Manual de instruções para Carregador de bateria Dynamite Prophet Precept. Dynamite Prophet Precept 2 páginas. 80w lcd ac/dc multi-chemistry battery charger

Imprimir página

Prophet™

Precept™

InstructIon Manual | BedIenungsanleItung | Manuel d'utIlIsatIon | Manuale dI IstruzIonI

SAfETy PRECAUTIONS ANd WARNINGS

NOTICE

WARNING: Failure to exercise caution while using this product and comply

All instructions, warranties and other collateral documents are subject to change

with the following warnings could result in product malfunction, electrical

at the sole discretion of Horizon Hobby, LLC. For up-to-date product literature, visit

issues, excessive heat, FIRE, and ultimately injury and property damage.

horizonhobby.com and click on the support tab for this product.

• Never leave the power supply, charger and battery unattended during use.

Meaning of Special Language

• Never attempt to charge dead, damaged or wet battery packs.

The following terms are used throughout the product literature to indicate various

• Never attempt to charge a battery pack containing different types of batteries.

levels of potential harm when operating this product:

• Never allow children under 14 years of age to charge battery packs.

• Never charge batteries in extremely hot or cold places or place in direct sunlight.

NOTICE: Procedures, which if not properly followed, create a possibility of physical

• Never charge a battery if the cable has been pinched or shorted.

property damage AND a little or no possibility of injury.

• Never connect the charger if the power cable has been pinched or shorted.

CAUTION: Procedures, which if not properly followed, create the probability of

• Never connect the charger to an automobile 12V battery while the vehicle is run-

physical property damage AND a possibility of serious injury.

ning.

WARNING: Procedures, which if not properly followed, create the probability of

• Never attempt to dismantle the charger or use a damaged charger.

property damage, collateral damage, and serious injury OR create a high probability

• Never attach your charger to both an AC and a DC power source at the same time.

of superficial injury.

• Never connect the input jack (DC input) to AC power.

• Always use only rechargeable batteries designed for use with this type of charger.

WARNING: Read the ENTIRE instruction manual to become familiar with

• Always inspect the battery before charging.

the features of the product before operating. Failure to operate the product

• Always keep the battery away from any material that could be affected by heat.

correctly can result in damage to the product, personal property and cause

• Always monitor the charging area and have a fire extinguisher available at all times.

serious injury.

• Always end the charging process if the battery becomes hot to the touch or starts

This is a sophisticated hobby product. It must be operated with caution and

to change form (swell) during the charge process.

common sense and requires some basic mechanical ability. Failure to operate

• Always connect the charge cable to the charger first, then connect the battery

this Product in a safe and responsible manner could result in injury or damage

to avoid short circuit between the charge leads. Reverse the sequence when

to the product or other property. This product is not intended for use by

disconnecting.

children without direct adult supervision. Do not attempt disassembly, use with

• Always connect the positive red leads (+) and negative black leads (–) correctly.

incompatible components or augment product in any way without the approval of

• Always disconnect the battery after charging, and let the charger cool between

Horizon Hobby, LLC. This manual contains instructions for safety, operation and

charges.

maintenance. It is essential to read and follow all the instructions and warnings in

• Always charge in a well-ventilated area.

the manual, prior to assembly, setup or use, in order to operate correctly and avoid

• Always terminate all processes and contact Horizon Hobby if the product malfunctions.

damage or serious injury.

WARNING: Never leave charger unattended, exceed maximum charge rate,

charge with non-approved batteries or charge batteries in the wrong mode.

Age Recommendation: Not for children under 14 years. This is not a toy.

Failure to comply may result in excessive heat, fire and serious injury.

This appliance is not intended for use by persons with reduced physical, sensory

or mental capabilities, or lack of experience and knowledge, unless they have

CAUTION: Always ensure the battery you are charging meets the

been given supervision or instruction concerning use of the appliance by a person

specifications of this charger and that the charger settings are correct. Not

responsible for their safety.

doing so can result in excessive heat and other related product

malfunctions, which can lead to user injury or property damage. Please

contact Horizon Hobby or an authorized retailer with compatibility questions.

SPECIfICATIONS

Included Items:

AC Input Voltage 100–240V AC (50–60Hz)

JST_XH Balance adapter

DC Input Voltage 11–18V DC

Banana plug to EC3

™

battery connector

Charge Current 0.1A to 6.0A (in 0.1A increments/80W maximum)

AC power cord (one region-US, EU, AU or UK)

Discharge Current 0.10 to 2.0A (in 0.1A increments/10W maximum)

OPTIONAL ACCESSORIES

Operating Temperature 0º C to + 50º C

dyN4012 - DC Power Cord

dyN5006 - Charge Adapter Banana to Deans Male

Balance Current Drain 300mA per cell

dyN5014 - Charge Adapter: Banana to Traxxas

Male

Charging Mode Ni-Cd/Ni-MH: Peak; Li-Po/Li-Ion/Li-Fe/Pb: CC/CV

dyN5033 - Temperature Sensor

OPERATING yOUR CHARGER

TABLE Of CONTENTS

SELF TEST AND PROGRAM SELECT SCREENS

Ni-Cd

PROgRAM SELECT USER SET

LITHIUM

a LITHIUM BATTERY TYPE

NICKEL-CADMIUM (NI-CD) BATTERIES

LITHIUM BATTERIES

Ni-Cd Charging

b LITHIUM BATTERY CHECK TIME

LITHIUM CHARgINg

Ni-Cd Discharging

c NI-MH SENSITIVITY (PEAK VOLTAgE)

d NI-CD SENSITIVITY (PEAK VOLTAgE)

LITHIUM BALANCINg CHARgINg

NI-CD CYCLE CHARgINg

LITHIUM FAST CHARgINg

e BATTERY CUTOFF TEMPERATURE

LITHIUM STORAgE CHARgINg

LEAD-ACID/SEALED-LEAD-ACID (PB) BATTERIES

f WASTE (BATTERY COOL-DOWN) TIME

g SAFETY TIMER

LITHIUM DISCHARgINg

PB CHARGING

Ni-MH

PB DISCHARGING

h BATTERY CAPACITY CUTOFF

NICKEL-METAL HYDRIDE (NI-MH) BATTERIES

USER SETTINGS

i BEEP AND BUZZER SOUND CONTROL

NI-MH CHARGING

SAVE DATA

j INPUT POWER LOW VOLTAgE CUTOFF

NI-MH DISCHARGING

LOAD DATA

USB DEVICE CHARgINg

NI-MH CYCLE CHARgINg

TROUBLESHOOTINg

SELf TEST ANd PROGRAM SELECT SCREENS

When the charger is powered ON, there is a series of self tests and the screen will

After self tests, the charger shows another screen (information may vary).

show the charger brand name and model number.

PROGRAM SELECT

DYNAMITE

LiPo BATT

DYNC2015

From any screen, press the Battery Type/Memory Button (H) to go back to the

main menu.

LITHIUM BATTERIES

Press the Battery Type/Memory Button (H) to change among the 7 main menu screens

and go to the PROGRAM SELECT Lithium BATT screen. Press the Select/Start Button (k)

Li3S 2.0A 12.59V

to enter this menu. This is the menu in which you set the standard Lithium battery charge

BAL 022:43 01082

parameters.

The Lithium battery type (Li-Po, Li-Ion or Li-Fe) chosen at USER SET setup shows on this

screen. Change Lithium battery type as needed in the USER SET menu (Li V. TYPE screen).

A. A Li-Po battery pack is balance charging

Change other Lithium battery settings as needed in the USER SET menu. Refer to the

B. Battery pack has 3 cells in series

PROgRAM SELECT USER SET section.

C. Charging rate is 2.0A (2000mAh)

LiPo CHARGE

d. Voltage being applied to the battery is currently 12.59V

4.6A

22.2V(6S)

E. Present charge level of the battery is 1082mAh

f. Time elapsed since the charge process started is 22:43 (22 minutes and 43 seconds)

Press the down (–) Button (I) or Up (+) Button (J) to go to one of the control screens

During charging, the down (–) Button can be pressed to show several parameter

(CHARgE, BALANCE, FAST CHg, STORAgE or DISCHARgE) to do what your battery needs.

messages on the LCD screen including: End Voltage, Capacity Cut-off, Safety Timer

Correctly connect your lithium battery to the charger (charging connector first and balancing

setting, Temperature Cut-off, External Temperature and Input Power Voltage. Press the

connector second). Press the Select/Start Button (k) and adjust charging parameters

Up (+) Button to see charge voltages for each cell and the down (–) Button to return

as needed. Press and hold the Select/Start Button (approximately 3 seconds) until the

to the Charge Monitor screen. To change the charging rate during charging, press the

screen changes to start the battery check/charge sequence. When the charge cycle starts,

Select/Start Button, then increase or decrease the rate using the down (–) Button

the charger compares the battery to charger settings. The screen will show battery and your

and Up (+) Button. The charger signals when the charging (or discharging) process is

settings information.

complete (if buzzer is set to ON).

If the information after R: (charger) and S: (settings) (A) does not match, press the

Press the Battery Type/Memory Button at any time to stop charging (or discharging).

Battery Type/Memory Button and change the lithium battery charging parameters

4.20

as needed. If the R: information matches S:, press the Select/Start Button to confirm.

0.00

After confirmation, charging starts and information will show on the LCD screen.

R: 3SER

S:3SER

CONFIRM

(ENTER)

80W LCD AC/DC Multi-Chemistry Battery Charger

A. Power Output Black (–)

B. Power Output Red (+)

C. Balance Circuit Adapter Board Connector

D. Temperature Sensor Port

Not to scale.

Not all wiring shown.

Not all connectors shown.

CAUTION: If at any time during the charge process the battery pack(s) become hot or begin to puff disconnect the battery immediately and discontinue the charge

process as batteries can cause fire, collateral damage and injuries.

CAUTION: Using a charge rate that is not compatible with the battery capacity may result in damage or malfunction of the charger or battery.

CAUTION: The Lithium charge program menus are to be used ONLY for the charging and discharging of Lithium battery packs. Charging other battery types using

the Lithium charge programs will damage the battery or the charger.

LITHIUM CHARGING

Press the Battery Type/Memory Button (H) until you reach the 7 main menus.

To select values other than the existing parameters:

Then press the Battery Type/Memory Button until you reach the PROGRAM

• Press the Select/Start Button so the charge current value (A) flashes

SELECT Lithium BATT screen. Press the Select/Start Button (k) to enter this menu.

• Press the down (–) Button or Up (+) Button to DECREASE or INCREASE the

Press the down (–) Button (I) or Up (+) Button (J) to reach the CHARGE screen

charge current value

and set charging parameters. The charging amperage (A) can be set between 0.1

• Press the Select/Start Button again to save the value and the voltage value (C)

and 6.0A. Voltage (C) is dependent on the number of cells in series (B) and Lithium

flashes

battery type.

• Press the down (–) Button or Up (+) Button to DECREASE or INCREASE the

LiPo CHARGE

voltage (and # of cells in series (B))

4.6A

22.2V(6S)

• Press the Select/Start Button again to save the voltage value

If no parameters are flashing, you can press the down (–) Button or Up (+) Button to

select another program such as BALANCE, FAST CHG, STORAGE or DISCHARGE.

To start charging, press and hold the Select/Start Button for 3 seconds.

LITHIUM BALANCING CHARGING

This program menu is specifically designed for the balanced charging of Lithium

To select values other than the existing parameters:

batteries, including Li-Po, Li-Fe and Li-Ion battery packs. In balance charging, each

• Press the Select/Start Button so the charge current value (A) flashes

cell in the battery pack is monitored and charged to the same capacity and voltage

• Press the down (–) Button or Up (+) Button to DECREASE or INCREASE the

levels, ensuring the optimum performance of the pack. Balance charging requires a

charge current value

battery with a balance adapter connector and a balance adapter board that has been

• Press the Select/Start Button again to save the value and the voltage value (C)

designed for your charger and your battery.

flashes

Press the Battery Type/Memory Button (H) until you reach the 7 main menus.

• Press the down (–) Button or Up (+) Button to DECREASE or INCREASE the

Then press the Battery Type/Memory Button until you reach the PROGRAM

voltage (and # of cells in series (B))

SELECT Lithium BATT screen. Press the Select/Start Button (k) to enter this menu.

• Press the Select/Start Button again to save the voltage value

Press the down (–) Button (I) or Up (+) Button (J) to reach the BALANCE screen and

set charging parameters. The charging amperage (A) can be set between 0.1 and 6.0A.

If no parameters are flashing, you can press the down (–) Button or Up (+) Button

Voltage (C) is dependent on the number of cells in series (B).

to select another program such as CHARGE, FAST CHG, STORAGE or DISCHARGE.

To start charging, press and hold the Select/Start Button for 3 seconds.

LiPo BALANCE

5.5A

22.2V(6S)

4.20

0.00

E. 2.1A USB Power Output Port

I. Down (–) Button

F. DC Power Input Port

J. Up (+) Button

G. AC Power Input Port

K. Select/Select/Start Button

H. Battery Type/Memory Button

L. LCD Screen

GETTING STARTEd

CAUTION: Never connect the AC and DC input cords to an active power source at the same time. This will void the warranty, cause product damage and possibly

injure the user.

When Using an External dC Power Source:

1. Connect the DC power cord to the charger dC Power Input Port (f).

2. Connect the DC alligator clips to the DC power source.

3. When the charger is powered ON, a message will appear on the LCd Screen (L).

NOTICE: Always connect cable polarities correctly.

NOTICE: Always consult 12V battery collateral materials or Horizon Hobby before

using with sources other than a standard AC wall outlet.

CAUTION: Always power ON the charger before connecting a battery, or damage to the charger and the battery can result.

• Connect the charger to the power source.

• Select the charging settings.

• Connect the battery to the charger.

• Start battery charging.

LITHIUM fAST CHARGING

Near the end of a standard charging cycle the charger switches from Constant

Current (CC) mode to Constant Voltage (CV) mode to slowly "top off" the current in

the battery pack as close as possible to the maximum capacity. In Fast Charge, the

CV mode is eliminated in order to greatly shorten the charging time; however, the

final capacity of the battery will be less than what you would get using the standard

charge method.

Press the Battery Type/Memory Button (H) until you reach the 7 main menus.

Then press the Battery Type/Memory Button until you reach the PROGRAM

SELECT Lithium BATT screen. Press the Select/Start Button (k) to enter this menu.

Press the down (–) Button (I) or Up (+) Button (J) to reach the FAST CHG screen

and set charging parameters.

The charging amperage (A) can be set between 0.1 and 6.0A. Voltage (C) is

dependent on the number of cells in series (B).

LiPo FAST CHG

0.1A

7.4V(2S)

LITHIUM STORAGE CHARGING

If you don't plan on using your battery for a long time it is best to charge (or

discharge) the battery to its optimal storage voltage and capacity. These voltage

values are different for Li-Po (3.85V), Li-Fe (3.3V) and Li-Ion (3.75V) battery packs.

Using Storage Charging, the charger will automatically charge or discharge (depend-

ing on the current charge level) the battery to an appropriate level.

Press the Battery Type/Memory Button (H) until you reach the 7 main menus.

Then press the Battery Type/Memory Button until you reach the PROGRAM

SELECT Lithium BATT screen. Press the Select/Start Button (k) to enter this menu.

Press the down (–) Button (I) or Up (+) Button (J) to reach the STORAGE screen

and set charging parameters.

The charging amperage (A) can be set between 0.1 and 6.0A. Voltage (C) is

dependent on the number of cells in series (B).

LiPo STORAGE

2.5A

11.1V(3S)

LITHIUM dISCHARGING

A battery pack's capacity can be verified by discharging the pack to its minimum

voltage level and measuring the current as the pack is discharged.

Press the Battery Type/Memory Button (H) until you reach the 7 main menus.

Then press the Battery Type/Memory Button until you reach the PROGRAM

SELECT Lithium BATT screen. Press the Select/Start Button (k) to enter this menu.

Press the down (–) Button (I) or Up (+) Button (J) to reach the DISCHARGE

screen and set discharging parameters.

The discharging amperage (A) can be set between 0.1 and 2.0A. Voltage (C) is

dependent on the number of cells in series (B).

LiPo DISCHARGE

5.0A

18.0V(3S)

PROGRAMMING qUICk GUIdE

Press the Battery Type/Memory Button (H) to change among main menu screens or to get to these main menu screens from a submenu screen.

Press the Select/Start Button (k) to get to submenus for adjusting operating parameters, to save value changes, or to start chosen battery charging actions.

Press the decrease (I) or Up (+) Buttons (J) to change between submenu screens or to change (Decrease or Increase) screen values.

LITHIUM BATTERIES (LI-PO)

PROGRAM SELECT

Ni-MH BATTERIES

PROGRAM SELECT

Ni-Cd BATTERIES

When Using an External AC Power Source:

1. Connect the AC power cord to the charger AC Power Input Port (G).

PROGRAM SELECT

2. Connect the AC power cord to the AC power source.

PROGRAM SELECT

3. When the charger is powered ON, a message will appear on the LCd Screen (L).

PROGRAM SELECT

Pb BATTERIES

PROGRAM SELECT

NICkEL-METAL HydRIdE (NI-MH) BATTERIES

To select values other than the existing parameters:

Press the Battery Type/Memory Button (H) to change among the 7 main menu

screens and go to PROGRAM SELECT Ni-MH BATT screen. Press the Select/Start

• Press the Select/Start Button so the charge current value (A) flashes

Button (k) to enter this menu. This is the menu in which you set the standard Ni-MH

• Press the down (–) Button or Up (+) Button to DECREASE or INCREASE the

battery charge parameters.

charge current value

Change other Ni-MH battery settings as needed in the USER SET menu. Refer to the

• Press the Select/Start Button again to save the value and the voltage value (C)

PROgRAM SELECT USER SET section.

flashes

• Press the down (–) Button or Up (+) Button to DECREASE or INCREASE the

voltage (and # of cells in series (B))

• Press the Select/Start Button again to save the voltage value

Press the down (–) Button (I) or Up (+) Button (J) to go to one of the control

If no parameters are flashing, you can press the down (–) Button or Increase

screens (CHARgE, DISCHARgE or CYCLE) to do what your battery needs. Correctly

Button to select another program such as CHARGE, BALANCE, STORAGE or

connect your Ni-MH battery to the charger. Press the Select/Start Button (k) and

DISCHARGE.

adjust charging parameters as needed. Press and hold the Select/Start Button

To start charging, press and hold the Select/Start Button for 3 seconds.

(approximately 3 seconds) until the screen changes to start the battery check/charge

sequence. After confirmation, charging starts and information will show on the LCD

screen.

CAUTION: The Ni-MH charge program menus are to be used ONLY for the charging and discharging of Ni-MH battery packs. Charging other battery types using the

Ni-MH charge programs will damage the battery or the charger.

NI-MH CHARGING

To select values other than the existing parameters:

• Press the Select/Start Button so the charge current value (A) flashes

Press the Battery Type/Memory Button (H) until you reach the 7 main menus.

• Press the down (–) Button or Up (+) Button to DECREASE or INCREASE the

Then press the Battery Type/Memory Button until you reach the PROGRAM

SELECT NiMH BATT screen. Press the Select/Start Button (k) to enter this menu.

charge current value

• Press the Select/Start Button again to save the value and the voltage value (C)

Press the down (–) Button (I) or Up (+) Button (J) to reach the NiMH CHARGE

screen and set charging parameters. The charging amperage (A) can be set between

flashes

0.1 and 6.0A.

• Press the down (–) Button or Up (+) Button to DECREASE or INCREASE the

voltage (and # of cells in series (B))

• Press the Select/Start Button again to save the voltage value

If no parameters are flashing, you can press the down (–) Button or Up (+) Button

to select another program such as CHARGE, BALANCE, FAST CHG or DISCHARGE.

To start charging, press and hold the Select/Start Button for 3 seconds.

NI-MH dISCHARGING

A battery pack's capacity can be verified by discharging the pack to its minimum

voltage level and measuring the current as the pack is discharged.

Press the Battery Type/Memory Button (H) until you reach the 7 main menus.

Then press the Battery Type/Memory Button until you reach the PROGRAM

SELECT NiMH BATT screen. Press the Select/Start Button (k) to enter this menu.

Press the down (–) Button (I) or Up (+) Button (J) to reach the NiMH

DISCHARGE screen and set discharging parameters. The discharging amperage (A)

can be set between 0.1 and 2.0A. The discharge level (B) can be set for AUTO or

from 0.1 to 25.0V.

To select values other than the existing parameters:

• Press the Select/Start Button so the discharge current value (A) flashes

• Press the down (–) Button or Up (+) Button to DECREASE or INCREASE the

discharge current value

• Press the Select/Start Button again to save the value and the voltage value (C)

flashes

NI-MH CyCLE CHARGING

• Press the down (–) Button or Up (+) Button to DECREASE or INCREASE the

The battery can be put through a series of charge/discharge cycles using this

voltage (and # of cells in series (B))

program. Cycling Ni-MH batteries can increase capacity and rejuvenate neglected

• Press the Select/Start Button again to save the voltage value

batteries. Discharge capacity and average battery voltage help you compare batteries

If no parameters are flashing, you can press the down (–) Button or Up (+) Button to

for the best run time and power.

select another program such as CHARGE, BALANCE, FAST CHG or STORAGE.

Press the Battery Type/Memory Button (H) until you reach the 7 main menus.

To start discharging, press and hold the Select/Start Button for 3 seconds.

Then press the Battery Type/Memory Button until you reach the PROGRAM

SELECT NiMH BATT screen. Press the Select/Start Button (k) to enter this menu.

Press the down (–) Button (I) or Up (+) Button (J) to reach the NiMH CYCLE

screen and set charge/discharge cycle count parameters.

(dYnc2015)

SAVE dATA

LiPo CHARGE

PROGRAM SELECT

SAVE [01]

4.6V

22.2V(6S)

4.6V

22.2V(6S)

SAVE DATA

2.0V

5000mAh

LiPo BALANCE

PROGRAM SELECT

LOAD [01]

5.5A

22.2V(6S)

5.5A

22.2V(6S)

LOAD DATA

2.0V

5000mAh

2.0V

5000mAh

PROGRAM SELECT

LiPo FAST CHG

LiPo

LiPo BATT

0.1A

7.4V(2S)

V. Type

3.7V

LiPo STORAGE

LiPo CHARGE

PROGRAM SELECT

SAVE [01]

LiPo/LiIo/LiFe

2.5A

19.8V(6S)

2.5A

19.8V(6S)

2.0V

5000mAh

4.6V

22.2V(6S)

SAVE DATA

CHK Time

10min

LiPo DISCHARGE

LiPo BALANCE

NiMH Sensitivity

5.0A

18.0V(6S)

5.0A

18.0V(6S)

PROGRAM SELECT

LOAD [01]

5.5A

22.2V(6S)

D. Peak

2.0V

D. Peak

5000mAh

Default

LOAD DATA

NiMH CHARGE Man

LiPo FAST CHG

NiCd Sensitivity

LiPo

LiPo BATT

CURRENT

0.1A

LiPo CHARGE

CURRENT

7.4V(2S)

0.1A

LOAd dATA

PROGRAM SELECT

SAVE [01]

D. Peak

Default

V. Type

3.7V

4.6V

22.2V(6S)

SAVE DATA

2.0V

5000mAh

PROGRAM SELECT

NiMH DISCHARGE

LiPo STORAGE

NiMH DISCHARGE

LiPo CHARGE

Temp Select

SAVE [01]

Temp Select

NiMH BATT

PROGRAM SELECT

LiPo/LiIo/LiFe

0.1A

2.5A

19.8V(6S)

0.1A

LiPo BALANCE

AUTO

Temp Cut-Off 80C

4.6V

22.2V(6S)

SAVE DATA

PROGRAM SELECT

2.0V

5000mAh

LOAD [01]

CHK Time

10min

5.5A

22.2V(6S)

LiPo DISCHARGE

NiMH CYCLE

LOAD DATA

2.0V

5000mAh

LiPo BALANCE

USER SET

Waste Time

NiMH Sensitivity

5.0A

DCHG>CHG

18.0V(6S)

LiPo FAST CHG

DCHG>CHG

LOAD [01]

PROGRAM SELECT

PROGRAM->

CHG>DCHG

1min

5.5A

22.2V(6S)

D. Peak

LiPo

Default

LiPo BATT

0.1A

7.4V(2S)

LOAD DATA

2.0V

5000mAh

NiCd CHARGE Man

NiMH CHARGE Man

NiCd CHARGE Man

V. Type

Saftey Timer

LiPo FAST CHG

LiPo STORAGE

NiCd Sensitivity

CURRENT

0.1A

CURRENT

0.1A

7.4V(2S)

0.1A

LiPo

180min

LiPo BATT

D. Peak

Default

2.5A

19.8V(6S)

LiPo/LiIo/LiFe

V. Type

3.7V

PROGRAM SELECT

NiCd DISCHARGE

NiMH DISCHARGE

Capacity Cut-Off

CHK Time

LiPo STORAGE

Temp Select

NiMH BATT

NiCd BATT

0.1A

LiPo DISCHARGE

0.1A

AUTO

LiPo CHARGE

2.5A

0.1A

19.8V(6S)

AUTO

PROGRAM SELECT

SAVE [01]

LiPo/LiIo/LiFe

5000mAh

Temp Cut-Off 80C

NiMH Sensitivity

5.0A

18.0V(6S)

4.6V

22.2V(6S)

SAVE DATA

CHK Time

2.0V

5000mAh

10min

D. Peak

NiMH CYCLE

NiCd CYCLE

Key Beep

LiPo DISCHARGE

USER SET

Waste Time

DCHG>CHG

LiPo BALANCE

NiMH CHARGE Man

NiMH Sensitivity

Buzzer

5.0A

18.0V(6S)

LiPo CHARGE

PROGRAM->

PROGRAM SELECT

CHG>DCHG

SAVE [01]

1min

PROGRAM SELECT

LOAD [01]

NiCd Sensitivity

5.5A

22.2V(6S)

CURRENT

0.1A

D. Peak

Default

4.6V

22.2V(6S)

SAVE DATA

2.0V

5000mAh

LOAD DATA

Input Power Low

2.0V

Input Power Low

5000mAh

D. Peak

Pb CHARGE

NiCd CHARGE Man

Pb CHARGE

NiMH CHARGE Man

Saftey Timer

PROGRAM SELECT

LiPo FAST CHG

NiMH DISCHARGE

NiCd Sensitivity

Cut-Off

11.0V

0.1A

CURRENT

2.0V (1P)

LiPo BALANCE

0.1A

2.0V (1P)

USER SET

180min

PROGRAM SELECT

CURRENT

0.1A

Temp Select

NiMH BATT

PROGRAM SELECT

LiPo

LOAD [01]

LiPo BATT

0.1A

7.4V(2S)

AUTO

D. Peak

Default

Pb BATT

5.5A

22.2V(6S)

Temp Cut-Off 80C

Pb DISCHARGE

NiCd DISCHARGE

Pb DISCHARGE

LOAD DATA

V. Type

2.0V

3.7V

5000mAh

NiMH DISCHARGE

Capacity Cut-Off

LiPo STORAGE

NiMH CYCLE

Temp Select

NiMH BATT

NiCd BATT

PROGRAM SELECT

0.1A

2.0V (1P)

LiPo FAST CHG

0.1A

AUTO

2.0V (1P)

0.1A

AUTO

USER SET

Waste Time

5000mAh

LiPo/LiIo/LiFe

2.5A

19.8V(6S)

DCHG>CHG

Temp Cut-Off 80C

LiPo

LiPo BATT

0.1A

7.4V(2S)

PROGRAM->

CHG>DCHG

NiCd CYCLE

CHK Time

10min

NiMH CYCLE

Key Beep

V. Type

USER SET

Waste Time

LiPo DISCHARGE

DCHG>CHG

LiPo STORAGE

DCHG>CHG

NiCd CHARGE Man

Buzzer

Saftey Timer

NiMH Sensitivity

5.0A

18.0V(6S)

PROGRAM->

CHG>DCHG

LiPo/LiIo/LiFe

1min

CURRENT

2.5A

19.8V(6S)

0.1A

D. Peak

Default

Input Power Low

CHK Time

Pb CHARGE

NiCd CHARGE Man

Saftey Timer

PROGRAM SELECT

NiMH CHARGE Man

0.1A

2.0V (1P)

NiCd DISCHARGE

LiPo DISCHARGE

Cut-Off

Capacity Cut-Off

11.0V

CURRENT

0.1A

NiCd Sensitivity

NiMH Sensitivity

180min

NiCd BATT

5.0A

0.1A

18.0V(6S)

AUTO

CURRENT

0.1A

Pb BATT

D. Peak

Default

D. Peak

Pb DISCHARGE

NiCd DISCHARGE

Capacity Cut-Off

NiMH DISCHARGE

NiCd CYCLE

NiMH CHARGE Man

Key Beep

NiCd BATT

0.1A

2.0V (1P)

AUTO

Temp Select

5000mAh

NiMH BATT

NiCd Sensitivity

0.1A

DCHG>CHG

AUTO

Buzzer

CURRENT

0.1A

Temp Cut-Off 80C

D. Peak

NiCd CYCLE

Key Beep

PROGRAM SELECT

NiMH CYCLE

Input Power Low

NiMH DISCHARGE

Pb CHARGE

DCHG>CHG

USER SET

Waste Time

Buzzer

Temp Select

NiMH BATT

DCHG>CHG

Cut-Off

0.1A

2.0V (1P)

AUTO

PROGRAM->

CHG>DCHG

1min

PROGRAM SELECT

Temp Cut-Off 80C

Pb CHARGE

Input Power Low

Pb BATT

NiCd CHARGE Man

NiMH CYCLE

Pb DISCHARGE

Saftey Timer

Cut-Off

11.0V

0.1A

2.0V (1P)

USER SET

Waste Time

CURRENT

DCHG>CHG

0.1A

2.0V (1P)

180min

PROGRAM->

CHG>DCHG

Pb BATT

Pb DISCHARGE

NiCd DISCHARGE

NiCd CHARGE Man

Capacity Cut-Off

0.1A

2.0V (1P)

Saftey Timer

NiCd BATT

0.1A

AUTO

CURRENT

0.1A

5000mAh

PROGRAM SELECT

NiCd CYCLE

NiCd DISCHARGE

Key Beep

Capacity Cut-Off

DCHG>CHG

NiCd BATT

0.1A

AUTO

Buzzer

Input Power Low

Pb CHARGE

NiCd CYCLE

Key Beep

DCHG>CHG

Cut-Off

11.0V

0.1A

2.0V (1P)

Buzzer

Pb BATT

Pb DISCHARGE

Input Power Low

Pb CHARGE

0.1A

2.0V (1P)

Cut-Off

0.1A

2.0V (1P)

PROGRAM SELECT

Pb BATT

Pb DISCHARGE

0.1A

2.0V (1P)

NiMH 2.0A 7.59V

CHG 022:43 01082

A. A Ni-MH battery pack is charging

PROGRAM SELECT

B. Charging rate is 2.0A (2000mAh)

NiMH BATT

C. Voltage being applied to the battery is currently 7.59V

d. Present charge level of the battery is 1082mAh

E. Time elapsed since the charge process started is 22:43

During charging, the down (–) Button or Up (+) Button can be pressed to show

several parameter messages on the LCD screen including: Ni-MH Sensitivity, Capacity

Cut-off, Safety Timer setting, Temperature Cut-off, External Temperature and Input

Power Voltage. The charger signals when the charging (or discharging) process is

complete (if Buzzer is set to ON).

Press the Battery Type/Memory Button at any time to stop charging (or discharging).

To select a value other than the existing parameter:

• Press the Select/Start Button so the charge current value (A) flashes

• Press the down (–) Button or Up (+) Button to DECREASE or INCREASE the

charge current value

• Press the Select/Start Button again to save the value

If no parameters are flashing, you can press the down (–) Button or Increase

NiMH CHARGE

Man

Button to select another program such as DISCHARgE or CYCLE.

CURRENT

0.1A

To start charging, press and hold the Select/Start Button for 3 seconds.

To select values other than the existing parameters:

• Press the Select/Start Button so the discharge current value (A) flashes

• Press the down (–) Button or Up (+) Button to DECREASE or INCREASE the

discharge current value

• Press the Select/Start Button again to save the value and the voltage value (B)

flashes

• Press the down (–) Button or Up (+) Button to DECREASE or INCREASE the voltage

• Press the Select/Start Button again to save the voltage value

If no parameters are flashing, you can press the down (–) Button or Increase

NiMH DISCHARGE

Button to select another program such as CHARgE or CYCLE.

0.1A

AUTO

To start discharging, press and hold the Select/Start Button for 3 seconds.

To select values other than the existing parameters:

• Press the Select/Start Button so the cycle type (A) flashes

• Press the down (–) Button or Up (+) Button to set the cycle type as

CHG>DCHG or DCHG>CHG

• Press the Select/Start Button again to save your choice and the number of

cycles (B) flashes

• Press the down (–) Button or Up (+) Button to DECREASE or INCREASE the

cycle count between 1 and 5

• Press the Select/Start Button again to save the cycle count value

NiMH CYCLE

If no parameters are flashing, you can press the down (–) Button or Increase

DCHG>CHG

Button to select another program such as CHARGE or DISCHARGE.

To start cycling, press and hold the Select/Start Button for 3 seconds.

3.7V

10min

Default

1min

3.7V

180min

10min

5000mAh

Default

11.0V

1min

3.7V

180min

10min

5000mAh

Default

11.0V

1min

180min

5000mAh

11.0V