Galaxy DX 93T Manual do Proprietário - Página 2
Procurar online ou descarregar pdf Manual do Proprietário para Transcetor Galaxy DX 93T. Galaxy DX 93T 11 páginas. 10 meter amateur mobile transceiver with built-in frequency counter & starlite face plate
Imprimir página
CHAPTER 1 SPECIFICATIONS
GENERAL
Model
Frequency Range
Emission
Frequency Control
Frequency Stability
Temperature Range
Antenna Impedance
Antenna Connectors
Input Voltage
Size
Weight
TRANSMITTER
RF Power Output
Spurious Emission
Unwanted Sideband
Audio Distortion
Frequency Response
Microphone
Clarifier Range
RECEIVER
Sensitivity for 10 dB (S+N)/N
Sensitivity for 12 dB (S+N)/N
Squelch Sensitivity
Selectivity
Image Rejection
AGC Figure of Merit
Audio Power Output
Audio Response
(SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE)
DX 93T
28.315 ~ 28.755 MHz
FM/AM/USB/LSB
Phase-Lock-Loop (PLL) Synthesizer
0.001%
-30°C to +50°C
50 Ohms
Standard SO-239 type
13.8V DC
7 7/8" (W) x 2 3/8" (H) x 10 3/4" (D)
4 lb. 10 oz.
AM/FM: 20W/8W/2W (HI/MED/LO)
USB/LSB: 50W PEP
-50 dB
-50 dB
10%
300 to 2500Hz
Dynamic
Coarse: ± 6.0KHz, Fine: ± 1.0KHz
AM: < 0.5 µV; USB/LSB: < 0.25 µV
FM: < 0.25 µV
< 0.5 uV
-55 dB
-50 dB
100 mV for 10dB Change in Audio Output
2.5W @ 10% Distortion
300 to 2500 Hz
- 2 -
CHAPTER 2 INSTALLATION
INSTALLING THE RADIO
Choose a convenient location for operation that does not interfere with driver or
passenger. This radio is supplied with a universal mounting bracket. When
mounting the bracket and radio to your car, make sure it is mechanically strong.
Also, provide a good electrical grounding connection to the chassis of vehicle.
Proceed as follows to install the radio.
1. Locate a convenient area in your vehicle for the installation of the radio.
Hold the mounting bracket with the radio in the location where the radio is to
be installed. Make sure nothing will interfere with either the radio or the
mounting bolts. Mark and then drill holes for the mounting bracket.
2. Most radio antennas come equipped with a PL-259 plug. Connect this plug to
the ANT. Jack in the rear of the radio.
3. Extending from the rear of the radio is a fused red and black wire for the DC
connections to the vehicle's electrical system. For best performance, it is
strongly recommended that the red lead be taken directly to the positive
terminal on the vehicle's battery and the black lead be connected to the
nearest chassis ground. (Note: This radio is designed for vehicles with
negative ground systems.)
Connections should be made using appropriate "crimp on" lugs of a size
large enough to make good contact with the bolt used to fasten to the battery
and the chassis ground. It is a good safety idea to install a second fuse that
would provide protection in case the red wire was to "fray" or get pinched
and short to the body of the vehicle, somewhere between the battery and the
radio.
High power radios such as this one require large DC current flow when in the
TX mode. Poor power connections cause supply voltage drops that can
substantially decrease the performance of your radio. A good DC connection
is probably one of the most important things for getting the best transmitter
performance and in some cases, least receiver noise.
4. Mount the microphone bracket near the radio in an easily accessible spot
using the two screws provided.
- 3 -