dbx 160A Brochura e especificações - Página 2
Procurar online ou descarregar pdf Brochura e especificações para Equipamento de música dbx 160A. dbx 160A 2 páginas. Compressor limiter
Também para dbx 160A: Manual de instruções (20 páginas)
Imprimir página
160A
COMPRESSOR / LIMITER
BYPASS
The compressor shall be a single channel unit, with
an audio frequency response of 20—20kHz +0, -
0.5dB, an electronically floating balanced input
impedance of not less than 38kΩ with a maximum
input level of not less than +24dBu and 1⁄4" TRS
and XLR input connectors. The output impedance
of the electronically floating balanced output shall
be no more than 32Ω (balanced or unbalanced) with
a maximum output level of not less than +24dBu,
into a balanced load with a minimum impedance of
not less than 600Ω, and +21dBu into and unbal-
anced load with a minimum impedance of not less
than 600Ω. It shall use an XLR connector. The out-
put impedance of the separate, 1⁄4" TRS unbalanced
output shall be no more than 21Ω with a maximum
output level of not less than +24dBm. Total har-
monic distortion shall be no more than 0.2% in typ-
ical operation with any amount of compression up
to 40dB. The unit shall have an output noise level
of not more than -90dBu and a dynamic range of
not less than 113dB. Output level shall be gain adjustable from -20dB to +20dB from nom-
inal gain via front panel gain controls and all outputs shall be capable of driving a short cir-
cuit indefinitely with maximum input applied. The compressor attack and release times shall
be program dependent. The compression threshold shall range from -40dB to +20dB, and
the compression ratio shall be variable from 1:1 through Infinity:1 through negative com-
pression to -1:1. The unit shall have a detector input, with a 1⁄4" TRS jack capable of bal-
anced or unbalanced operation. The front panel shall have the following controls and switch-
es:, Bypass switch, Master/Slave switch, Compressor Threshold, OverEasy or Hard Knee
selector switch, Compression Ratio, Output Gain, and Display Selector switch. The follow-
ing LEDs for metering and status indication shall exist: Bypass, Slave, Threshold (3 LEDs),
Input/ Output Display Selected (2 LEDs), Input/Output Level (19 LEDs) and Gain Reduction
(12 LEDs). The unit shall have a 1⁄4" TRS jack at the rear panel, allowing stereo strapping
with a second unit of the same design for stereo operation with true RMS summing of input
levels There shall also be a calibration control for the level meter, at the rear panel. The unit
shall incorporate a detachable IEC mains cable and the power requirement shall be 90—
130VAC 50/60Hz or 200—250VAC 50/60Hz. Dimensions shall be 1.75" x 19" x 6.5"
(4.45cm x 48.2cm x 16.51cm). The net weight shall be 4.41lbs (1.99 kg) and the shipping
weight shall be 6.62 lbs (2.99kg). The unit shall be a dbx 160A Compressor/Limiter.
dbx engineers are constantly working to improve the quality of our products. Specifications
are, therefore subject to change without notice.
®
A Harman International Company
-10
3:1
-20
0
BELOW
ABOVE
SLAVE
OVEREASY
2:1
-30
+10
-40dBu
+20dBu
1:1
THRESHOLD
COMPRESSION
Input: Connector: 1⁄4" TRS and XLR, Floating Balanced; XLR: Pin 2 hot,
Phone: Tip Hot.
Impedance: 40kΩ.
Maximum Level: +24dBu, Balanced or Unbalanced (Absolute).
CMRR: >45dB (Any Frequency).
Detector Input: Connector: 1⁄4" TRS phone, Floating Balanced.
Impedance: >200kΩ.
Maximum Level: +28dBu, Balanced or Unbalanced.
Output: Connector: XLR, Floating Balanced; Pin 2 Hot.
Impedance: 30Ω.
Maximum Level: (Balanced): +24dBm; <0.3% THD.
Maximum Level: (Unbalanced): +20dBm; <0.3% THD
Noise: <-90dBu, Unweighted (20Hz — 20kHz).
Frequency Response: 20Hz —20kHz, +0,
-0.5dB; +0, -3dB 0.5Hz and 90kHz.
THD: <0.2%, Typical, any amount of
compression up to 40dB @ 1kHz.
Output: Connector: 1⁄4" TRS phone, Unbalanced.
Impedance: 20Ω.
4:1
0
INPUT
6:1
10:1
-10
+10
OUTPUT
-40
30
:1
-5:1
-2:1
-1:1
-20dB
+20dB
C O M P R E S S O R
OUTPUT
RATIO
GAIN
DISPLAY
LEVEL
20
15
10
8
6
5
4
3
2
1
0
1
2
4
6
10
20+
GAIN REDUCTION
/
L I M I T E R
Maximum Level: +24dBm.
Compression: Threshold Range: -40dBu to +20dBu.
Threshold Characteristic: OverEasy® or Hard Knee.
Compression Ratio: Variable 1:1 to :1 thru to -1:1; >60dB maximum compres-
sion.
Attack Time: Program dependent; typically 15ms for 10dB, 5ms for 20dB,
3ms for 30dB.
Release Time: Program Dependent; Typically 8ms for 1dB, 80ms for 10dB,
400ms for 50dB; 125dB/sec rate.
System Performance:
Dynamic Range: >113dB.
Gain Adjustment Range: Variable from -20dB to +20dB.
Stereo Coupling: True RMS Power Summing™
Summing: 1⁄4" TRS phone jack.
Hardware: Power Cord: IEC-Type connector.
Operating Voltage: DO: 90-130VAC, 50/60Hz; EU: 200-250VAC, 50/60Hz.
Operating Temperature: 0°C to 45°C (32°F to 113°F).
Dimensions (H x W x D): 1.75" x 19" x 6.5"(4.45cm x 48.2cm x 16.51cm).
Weight: Net Weight: 4.45 lbs (1.99 kg) Shipping Weight: 6.62 lbs (2.99 kg)
FOR MORE INFORMATION CONTACT:
dbx Professional Products
8760 S. Sandy Pkwy.
Sandy, Utah 84070
Phone (801) 568-7660
Fax (801) 568-7662
Int'l Fax (801) 568-7583
http://www.dbxpro.com