Autonics PSAN Series Manual do produto - Página 3

Procurar online ou descarregar pdf Manual do produto para Instrumentos de medição Autonics PSAN Series. Autonics PSAN Series 6 páginas. Display type pressure sensors
Também para Autonics PSAN Series: Manual (2 páginas), Manual (13 páginas), Manual do produto (7 páginas)

Imprimir página

Connections

Color

Function

Brown

Blue

0 V

Black

OUT 1

White

OUT 2

Orange

Option input / output

■ NPN open collector output

Brown

LOAD

Black

LOAD

OCP

White

OCP

①

②

Orange

Output

impedance

Blue

• ①: Option voltage / current output model, ②: Option external input model

• OCP (over current protection circuit)

• There is no short circuit protection circuit. Do not connect directly to power or capacitive loads.

• The control output is abnormal when the control output circuit is shorted or over current is

supplied.

• Pay attention to the input impedance of the connected device when using analog voltage

output. Be sure to the voltage drop due to the resistance of the wiring when extending the

wiring.

Installation

■ One-touch fitting

Pneumatic type

Fluid type

12 mm

spanner

17 mm

spanner

■ Bracket

Use spring washers and hexagon wrench bolts (tightening torque: ≤ 3 N m) to select

and install a bracket suitable for your environment.

Connector type

• Bracket A

• Bracket B

■ Installation configuration

• Sold separately: Front cover (PSO-P01), Panel

bracket (PSO-B02/B03)

• Panel thickness: 0.8 to 3.5 mm

Front cover

(PSO-P01)

Panel bracket

(PSO-B02)

Installation

panel

Pressure sensor

Error

Display Cause

When external pressure is input while

adjusting zero point.

ERR1

When overload is applied on control output

ERR2

When 'ST1', 'ST2' setting range is not met in

auto sensitivity setting mode.

ERR3

When applied pressure exceeds high-limit of

display pressure range.

HHHH

When applied pressure exceeds low-limit of

display pressure range.

LLLL

-HH-

Auto shift correction error.

-LL-

-HL-

■ PNP open collector output

Brown

OCP

Black

LOAD

OCP

White

LOAD

①

②

Orange

Output

impedance

Blue

Connect the metal part with a

spanner so that no large force is

applied to the unit body.

(tightening torque: ≤ 10 N m, it may

cause malfunction.)

Cable type

• Bracket C

■ Wiring

• Do not pull the wiring with a force

of more than 30 N.

Troubleshooting

Try again after removing external

pressure.

Remove overload.

Check setting conditions and set

proper setting values.

Apply pressure within display pressure

range.

Set the corrected setting value within

setting pressure range.

Specifications

PSAN-

Model

□V01C□□-□

□01C□□-□

Pneumatic type model: Gauge pressure

Pressure Type

Fluid type model: Gauge pressure

Pressure

Negative

Static

Min display unit

0.1 kPa

Rated pressure

0.0 to -101.3

0.0 to 100.0

range

kPa

Display & setting

5.0 to -101.3

-5.0 to 110.0

pressure range

kPa

Display type

7 Segment LED, 4 ½ digit

Display accuracy

-10 to 0 ℃: ≤ ±1% F.S., 0 to 50 ℃: ≤ ±0.5% F.S.

Rated pressure

Rated

Max. pressure

×2

pressure ×2

01) Only for static pressure, rated prssure range 100.0 kPa model

02) The unit is sealed structure. It is based on atmospheric pressure 101.3 kPa.

Applicable

Pneumatic type

medium

(air, non-corrosive gas)

Connection type

Connector type

Cable

Ø 4 mm, 5-core, 2 m

Wire spec.

AWG24 (0.08 mm, 40-core), insulator diameter: Ø 1 mm

Front case: PC

Back case: (back port) PC / (bottom

Material

port) PBT+GF15%

Pressure port: Brass-nickel plated

Protection

Connector type: IP40 (IEC standard)

structure

Approval

ᜢ ᜫ

Unit weight

Back port: ≈ 80 g (≈ 165 g)

(packaged)

Bottom port: ≈ 85 g (≈ 170 g)

12 - 24 VDCᜡ (ripple P-P: ≤ 10%)

Power supply

Allowable voltage

90 to 110% of rated voltage

range

Current consumption

≤ 50 mA

01)

Control output

NPN open collector output / PNP open collector output model

Load voltage

≤ 30 VDCᜡ

Load current

≤ 100 mA

Residual voltage

NPN: ≤ 1 VDCᜡ, PNP: ≤ 2 VDCᜡ

Hysteresis

According to output operation mode

Repeat error

±0.2% F.S. ±min display interval

Response time

2.5, 5, 100, 500, 1000 ms

Protection circuit

Output short over-current protection circuit

Insulation resistance

≥ 50 MΩ (500 VDCᜡ megger)

Dielectric strength

1,000 VACᜠ 50 / 60 Hz for 1 min

1.5 mm amplitude at frequency of 10 to 55Hz (for 1 min) in each X, Y,

Vibration

Z direction for 2 hours

Ambient temperature

-10 to 50 ℃, Storage: -20 to 60 ℃ (no freezing or condensation)

Ambient humidity

30 to 80%RH, Storage: 30 to 80%RH (no freezing or condensation)

01) Current output: ≤ 75 mA

02) Refer to 'Output operation mode'. ±1digit error may occur due to pressure unit operation.

Analog output

Voltage (1 - 5 VDCᜡ ±2% F.S)

Output impedance

1 kΩ

Linearity

≤ ±1% F.S

Zero-point

≤ 1 VDCᜡ ±2% F.S.

Span

≤ 4 VDCᜡ ±2% F.S.

Resolution

1/1000 or 1/2000 (different by pressure type and display unit)

Response time

50 ms

Minimum Display Interval

Pressure

Negative

Static

Min display

0.1 kPa

interval

1/1000

1/2000

1/1000

Resolution

Display unit

MPa

0.001

kPa

0.1

kgf/cm

0.001

bar

0.001

psi

0.01

mmHg

0.4

inHg

0.02

mmH

0.1

01)

01) Multiply display value by 100.

PSAN-

PSAN-□1□□□-□

□C01□□□-□

or sealed gauge pressure

01)

02)

Compound

1 kPa

0.1 kPa

-101.3 to 100.0

0 to 1,000 kPa

kPa

-101.3 to 110.0

-101.3 to 1,100 kPa

kPa

• Pneumatic type:

Rated pressure ×1.5

Rated pressure

• Fluid type: Rated

×2

pressure ×2

Fluid type (non-corrosive gas and

fluid that do not corrode stainless

steel 316L)

Cable type / connector type

Connector type: Ø 4 mm, 5-core, 2 m

Cable type: Ø 4 mm, 5-core, 3 m

Front case: PC

Back case: PA6

Pressure port: SUS304/SUS316L

Connector type: IP40 (IEC standard)

Cable type: IP65 (IEC standard)

Connector type: ≈ 88 g (≈ 173 g)

Cable type: ≈ 90 g (≈ 167 g)

02)

Current (DC 4 - 20mA ±2% F.S)

≤ ±1% F.S

≤ DC 4 mA ±2% F.S.

≤ DC 16 mA ±2% F.S.

70 ms

Compound

1 kPa

0.1 kPa

1/2000

1/1000

1/2000

1/1000

0.001

0.01

0.1

1/2000

0.1

0.001

0.02

0.8

0.03

0.1