activTek activBlaster Manual de início rápido - Página 3

Procurar online ou descarregar pdf Manual de início rápido para Filtro de ar activTek activBlaster. activTek activBlaster 4 páginas.

Imprimir página

OPERATING PROCEDURES:

• Always wear proper safety equipment!

• In the area to be treated, determine a suitable, centrally located,

dry location to place the unit and plug in.

• Turn off smoke/fire alarm systems in building or residence, if

system is known to be sensitive to ozone gas.

• Clean or vacuum the air intake screens on ventilation systems in

areas with high concentrations of smoke or airborne dust when

treating air conditioning duct system.

• Turn the air conditioning fan to "On" (if applicable) for

continuous cool airflow throughout building, unit, or house.

CAUTION! - Prior to operating this unit, consult warning

section of this user's manual.

• Make sure the area being treated is sealed shut to re-circulate the

ozone and prevent the ozone from escaping.

• Vacate the area of all persons, animals, and rubber products or

rubber plants (see activBlaster Warnings).

• Place "DO NOT ENTER" caution signs on all entrances/exits to

treated area.

• Place respiratory breathing mask on.

• Turn "On" the unit by setting the clock timer for the

predetermined time treatment period and adjusting to the

appropriate output percentage.

• Exit area immediately.

POST TREATMENT PROCEDURES:

• When time period is expired, you should re-enter only with

breathing mask in place to vent out the area. If feasible, open

windows and doors to vent area.

• Re-test the area after the pre-calculated venting time period

to check whether the ozone level is safe to breathe without

breathing apparatus.

ELECTRICAL CONSIDERATIONS:

The activBlaster unit is designed to use a normal household voltage

of 120V. In accordance with the specifications of the National

Electrical Code and for safety measures, a three-prong grounding

plug is standard to the equipment. This three-prong plug mates

with a standard three-prong ground wall receptacle.

REPLACEMENT BULB

PART #

ITEM

US71102

Replacement UV HO Bulb

Manufacturer shall not be held liable for consequences of any actions by the purchaser

and/or applicator while using or applying activBlaster.

Due to the variety of operational conditions and applications for these systems, the

user through his/her own analysis and testing is solely responsible for making the final

selection of the type of system and assuming that all performance, safety, and precaution

requirements of the applications are met.

ACTIVBLASTER WARNINGS:

OZONE IS CONSIDERED A TOXIC AND HAZARDOUS

SUBSTANCE BY THE FEDERAL GOVERNMENT, SPECIFICALLY

OSHA (OCCUPATIONAL SAFETY AND HEALTH ACT) (29 USC

655, 657). IT IS A POWERFUL OXIDIZER WHICH DESTROYS

ORGANIC SUBSTANCES. ALL SAFETY PRECAUTIONS HEREIN

MUST BE ADHERED TO AND COMMON SENSE MUST BE

USED. DO NOT ATTEMPT TO OPERATE THE ACTIVBLASTER

SYSTEM WITHOUT FIRST READING AND UNDERSTANDING

ALL INFORMATION AS PROVIDED BY THE MANUFACTURER

HEREIN.

• Do not under any circumstance cut, remove, or replace the

third prong from the electrical cord. If in the event a three-

prong receptacle cannot be located in the area to be treated,

a temporary connection may be made (where local codes

permit) utilizing P&S #1919 Adapter or equivalent.

The adapter provides a means for plugging in the three-

prong cord into a two-prong receptacle. When used around

dampness or water, use a GFI outlet.

• Vacate the area of persons, animals, and rubber plants before

starting the system. The amount of ozone that is produced by

activBlaster is much higher than the maximum permissible

OSHA standard for ozone concentration in an inhabited,

enclosed area (.1 ppm). Therefore, no person or animal should

remain in or enter the treated area until the area is vented

properly for the recommended time period, and the level of

ozone has depleted down to the acceptable level (.1 ppm). *Do

not breathe or inhale the ozone gas.

• A "Caution Do Not Enter" sign should be placed on all

entrances/exits to the treated area at all times during and after

the treatment until such time as the ozone level is .1 ppm, safe

for re-entry.

• Do not breathe the ozone. The applicator should wear

appropriate respiratory (breathing) mask when entering a

treated area afterwards. If it is absolutely necessary to re-enter

the treated area, you should wear a respiratory breathing mask

and turn off the system.

• Vent area before re-entering. The area may smell of ozone

when you re-enter (ozone smells like air immediately after a

thunderstorm). If the ozone level measures more than the 0.1

ppm concentration, the area should be vented longer until the

level is reduced.

• Do not disassemble the activBlaster unit to service, or look

directly inside at the ultraviolet light while it is operating.

• Do not use in an overheated (over 120˚ F.) or explosive

atmosphere.

Some physical symptoms of prolonged or excessive ozone

exposure may result in: burning, watery, or irritated eyes, nose,

and throat; nausea; headache; difficulty breathing; dry cough;

irritation to nasal passages, throat, bronchial, and pulmonary

membranes. Should this occur, see a physician immediately.

Persons suffering from chronic breathing problems are known to

be sensitive to ozone.