ADEO SCREEN TENSIO CLASSIC PSCHP0800 Manual do utilizador - Página 5

Procurar online ou descarregar pdf Manual do utilizador para Ecrã de projeção ADEO SCREEN TENSIO CLASSIC PSCHP0800. ADEO SCREEN TENSIO CLASSIC PSCHP0800 14 páginas.

Imprimir página
2)
Check the connections between the control commutator and the motor.
3)
Check that the motor is not in the phase of thermal protection (wait few minutes to cool the motor).
4)
Check that the wire between the motor and the inverter is not cut.
FEATURES:
The motor is realised with a tubular asynchronous monophasic runner with the following features:230V, 50 Hz, 90 W, 17 revolutions per minute.
The motor of the screens with case is located in the right side of the screen (on request it is possible to have it on the left) if the screen is without case the motor is located on the
left. It works through a radio remote control supplied from the producer.
ELECTRIC CONNECTIONS:
The electric cabling must respect the CEE regulations. According to the CEI 335-1 norm, you have to install an upstream omni polar switchgear with a minimum contacts opening
spacing of 3 mm. Please follow the instruction on the connection scheme see FIG 5.
MEMORISING THE "FIRST" TRANSMITTER ON SCREEN
Caution! – DO NOT follow this procedure if Transmitters have already been memorised on screen.
01. Turn on the power to screen: the motor makes 2 LONG motions (= no transmitters memorised).
02. (Within the next 5 seconds) Press and hold down key
memorisation complete).
Caution! – Once this part of programming has been completed, the Up and Down movements of the motor are still not associated to keys
Transmitter. This will take place automatically during one of the three programmino procedures of limit switches "0" and "1".
PROGRAMMING OF LIMIT SWITCH POSITIONS upper "0" and lower "1"
01. Press and hold down key
(or
ATTENTION!!! the correct "0" position is when the low bar of the screen is positioned at 2 mm from the case.
02. Press and hold down key
until the motor performs 1 VIBRATION; then release the key.
03. Press and hold down key
again (for approx. 5 seconds), until the motor performs 4 SHORT motions; then release the key.
04. Press and hold down key
until the motor performs 2 LONG motions (= the "0" position is memorised); then release the key.
05. Press and hold down key
(or
06. Press and hold down key
until the motor performs 1 VIBRATION; then release the key.
07. Press and hold down key
again (for approx. 5 seconds), until the motor performs 4 SHORT motions; then release the key.
08. Press and hold down key
until the motor performs 2 LONG motions (=position "1" is memorised); then release the key.
Note – Once this programming procedure is complete, key
manoeuvre. The roller shutter/awning will stop at programmed positions "0" and "1" during each of these manoeuvres.
REPOSITIONING OF LIMIT SWITCH lower "1"
01. Press and hold down key
(for approx. 5 seconds), until the motor performs 1 VIBRATION, then release the key.
02. Press and hold down keys
and
release the keys.
03. (within the next 4 seconds) Press keys
04. (within the next 4 seconds) Press and hold down keys
keys.
DELETING TRANSMITTERS FROM THE MEMORY
Caution! – This procedure deletes all memorised transmitter codes from screen memory. The procedure can be performed both with a memorised transmitter as well
as a non memorised transmitter.
If the transmitter is memorised, proceed as follows:
01. Press and hold down key
(for approx. 5 seconds), until the motor performs 1 VIBRATION; then release the key.
02. Press and hold down key
until the motor performs 3 LONG motions; then release the key exactly on the third movement.
03. Press and hold down key
until the motor performs 3 LONG motions; then release the key exactly on the third movement.
04. Press and hold down key
until the motor performs 3 LONG motions; then release the key exactly on the third movement.
After a few seconds the motor performs 5 LONG motions (= all transmitters deleted).
If the Transmitter is not memorised, proceed as follows:
A. Disconnect from power supply (if connected) and connect again the tubular motor to the power supply. Within the next 60 seconds,
press and hold down key
(for approx. 5 seconds), until the motor performs 1 VIBRATION; then release the key.
B. (within the next 5 seconds) Disconnect from the power supply.
C. Power the motor again: the previous procedure, from point 01 to point 04, must be performed within 60 seconds from turning on the
power supply.
TROUBLESHOOTING OF THE MOTORISED SYSTEM:
1)
Check the power supply 230 V.
2)
Check that the motor is not in the phase of thermal protection (wait few minutes to cool the motor).
3)
Check that the wire between the motor and the power supply is not cut.
ATTENTION the installation of the screen, the electric connections, the setting of the limit switches and the test of malfunctions of the motorised rolling up and
down, must be made from authorised staff only. It is not possible to change the connection cable. If the cable is damaged the screen must be changed.
The warranty is not valid in case of wrong installation, tampering or repair by technicians not authorized or tampering of the seal of limit switches.
If necessary, for further information over these points contact our technical office.
Adeo Screen screens are covered by 24 months Manufacturer' s Warranty on the curtain + 12 months on mechanical and structural parts only ( electric engines covered by
independent 60 months warranty ) The warranty starts from the date of the manufacturer' s invoice. Adeo Screen warranty covers damages and malfunction deriving from normal
use of the screen and free of charge replacement of defective parts.
Withdrawal of screen, forwarding charges and custom duties are to be paid by the customer.
The warranty is not valid in case of wrong installation, tampering or repair by technicians not authorized by Adeo Screen or tampering of the seal of limit switches. The
adjustment of limit switches must be done only by technicians authorized by Adeo Screen. The warranty does not cover the parts that show normal wear and tear, deriving from
particular weather or environmental conditions as well.
Damages or tampering of screens in transit/shipment are not covered by warranty: an accurate inspection when goods are collected/received is, therefore, recommended. The
screens sent back to be repaired will not be accepted without a Return Material Authorization number (R.M.A.) FROM Adeo Screen and/or without a proper packing.
Adeo Screen reserves the right to check that all the details above mentioned have been complied with in order to consider the warranty valid.
The tensioned screen is equipped with jointed blocks and side cables that are adjusted during testing of the screen.
However, the blocks can be adjusted to be more or less inclined even after purchase.
If you want to change the position of the blocks for a different esthetic result, proceed as follows:
- Loosen the screw on the rear of the block to release the cable.
- Choose the inclination that you prefer, making sure, however, that the block can still tighten the cable.
- Tighten the screw behind the block to hold the cable.
- Do the same on the opposite side, making sure that the positions of the two blocks are equal.
- Cut the part of the cord that is no longer needed.
If you don' t want to change the position of the blocks, cut off the extra cord.
Attention! After to have cut the ropes it is not more possible to lower the counterbalances ulteriorly.
RADIO INTEGRATED MOTORIZED SCREENS (Fig. 5)
on the transmitter for about 3 seconds and release it as soon as the motor start the first of 3 LONG motions (=
) on the transmitter until the roller shutter/awning reaches the "0" position required by the user; then release the key.
) until the roller shutter/awning reaches the position "1" required by the user; then release the key.
on the Transmitter will control the Up manoeuvre of the roller shutter/awning, while key
simultaneously (for approx. 5 seconds), until the motor starts to automatically move the roller shutter / awning into position "1", then
and
to position the roller shutter/awning in the new position "1".
and
simultaneously until the motor performs 2 LONG motions (= new position "1" memorised), then release the
WARRANTY ON SCREENS
and
on the
will control the Down
mod. TENSIO