ADEO SCREEN ALUMAX PSCHP0061 Manual do utilizador - Página 5
Procurar online ou descarregar pdf Manual do utilizador para Acessórios ADEO SCREEN ALUMAX PSCHP0061. ADEO SCREEN ALUMAX PSCHP0061 16 páginas. Roller screen
Imprimir páginaTechnical characteristics:
Voltage: 230V
Frequency: ~Hz50
Power: 170W
Torque: 8Nm
Speed: 17Rpm
FIG. 3
Max nr. of cycles: 2
Cable length: 3mt
Mechanical strength:
EN14202 conformant
Operating T° :
from –20 to +55 ° C
END STOPS ADJUSTMENT FOR MOTORISED VARIANT ROLLER SCREENS
WARNING - READ CAREFULLY BEFORE PERFORMING ADJUSTMENTS
Adjustments shown on Fig. 4 must be performed by authorised and specialised personnel only. Incorrect performance of the procedures described
may result in damages to the product which will not be covered by guarantee. End stops adjustment varies depending on the motor's position (right
or left side) or on drop of the curtain (front or rear); the diagram on Fig. 4 is sectioned based on these variants. Adjustment is performed with a 4 mm
hex wrench (included).
END STOPS ADJUSTMENT SCREWS ARE POSITIONED IN THE BOTTOM PART OF THE SCREEN, AND NOT IN THE RIGHT OR LEFT HAND
SIDES. DO NOT ADJUST THE END STOPS WHEN UP OR DOWN BUTTON IS ACTIVATED.
WARNING
End stop is adjusted so as to allow the projection sheet to wind around the roller at least 1.5 times to avoid the sheet coming loose. Special attention
must be paid when end stops are adjusted in such a way that projection sheet unwinds beyond the factory setting. This is allowed within a limit of 3
cm without posing a risk to the product. Incorrect adjustment of end stops can cause:
-Projection sheet coming away from the roller
-Projection sheet winding the wrong way, with ensuing damage to flatness of the projection surface and to winding mechanisms
-Breaking of bottom end black frame welding (framed screens)
-Excessive strain on motor with possible ensuing damage and activation of motor's thermal resistance
-Excessive winding of the end stop adjustment system with ensuing breaking of the mechanical part
GUARANTEE
Operators are reminded that in cases where seals have been tampered with and where any damages have resulted from incorrect adjustment, repair
interventions shall not be covered by guarantee.
ANOMALY
Screen does not open/close
Screen does not open/close
Screen moves in one direction only
Screen has come down but will not go up
R.I. screen is blocked
As is the case for installation procedures, when the product reaches the end of its useful life, disposal operations must be carried out by qualified
personnel.
The product is made up of various types of material: some can be recycled, others have to be disposed of. You must follow applicable recycling or
disposal regulations in force in your area for this product category.
As shown in the picture on the left, you must not throw the product into a domestic litter bin. Either dispose of the various components separately,
pursuant to the regulations applicable in your territory, or hand the product over to a vendor upon purchasing a similar new product.
Warning: local regulations can foresee heavy fines in case of unlawful disposal of this product.
Screens are covered by a 24 month guarantee for projection curtains, plus 12 months for mechanical and structural parts, and a 60 month period for
motors installed on single products.
The guarantee's validity starts from the date of purchase on the part of the end user; such purchase date must be documented by a purchase
receipt when requesting technical interventions or replacement.
The guarantee covers damages and malfunctions resulting from normal use of the products, and replacement free of charge of components with
manufacturing flaws; the service includes collection/delivery by a contracting courier at the manufacturer's expense (only for Italy and Poland
guarantees).
The guarantee is forfeited in case of incorrect use or installation, tampering or repair on the part of personnel not authorised by manufacturer or
tampering with the seal for end stop adjustment, which can only be carried out by technicians or specialised personnel. The guarantee does not
cover damages resulting from normal wear and tear or from particular weather or environmental conditions. Damages to goods during transport or
handling operations are not covered by guarantee.
Goods must therefore be checked carefully upon receival.
Screens returned for repair will not be accepted unless they are accompanied by the manufacturer's RMA (return material authorisation) and
adequately packed.
Manufacturer reserves the right to verify the existence of the requisites for the validity of the guarantee.
MOTORISED VARIANT ROLLER SCREENS
ELECTRICAL CONNECTION: electric cabling must be conformant with applicable IEC standards. IEC norm EN 60335-1
requires that supply network be fitted with an omnipolar selector switch with contact opening distance of at least 3 mm. For
the screen's control use only the selector switch provided by manufacturer, or equivalent model, and follow the instructions of
the connection diagram shown on Fig. 4 (if the motor is mounted on the left, the colours of the wires must be inverted, i.e.
descending = brown, ascending = black). The selector switch must be mounted within sight distance of the product, at a 1.5 -
1.8 m height from the floor.
WARNING: Correctly performed, state-of-the-art, norm-compliant electrical connections are important to prevent accidents
and to ensure the screen's optimal and unaltered performance in time. Prior to carrying out any operation on electrical parts
ensure that power supply is disconnected. In screens fitted with cases the motor is positioned on the right hand side of the
screen as seen from the front (upon request it can be located on the left). Never connect two or more motors to the same
selector switch without a control unit or two switches to the same motor.
TROUBLESHOOTING
POSSIBLE CAUSE
Not connected to power supply
The motor's thermal protection is activated
A power supply cable has not been connected
End stop has been incorrectly modified
Remote control batteries are flat
PRODUCT'S DISPOSAL
SCREEN GUARANTEE
REMEDIAL ACTION
Check electrical connection
Allow to cool down for about 10 minutes
Check connection to selector switch
Call vendor or a technician for assistance
Replace batteries