Gallo Tech GTS-2 Manual de operação e instalação - Página 13

Procurar online ou descarregar pdf Manual de operação e instalação para Arrancador remoto Gallo Tech GTS-2. Gallo Tech GTS-2 15 páginas. Keyless rfid push button start & security system

Imprimir página

1. Key Fob & Programming Function Set up

Installing Connector C4:

2 Pin Wire Harness (

Control Module Power, Parking lights)

C4: RED 15 Amp fused wire – + 12v Constant Battery Input (Control Module Supply Power). This connection

should have constant +12v available (BAT terminal on ignition switch or equivalent). Solder connect the RED wire.

C4: YELLOW – Parking Light +12v output 10 Amps fused. Solder connect one of the YELLOW wires to the

vehicle's parking lights. If parking lights require more than 5 amps (not normal) use an external 30 Amp relay.

Installing Connector C5:

7 Pin Wire Harness

(Trunk Release, Door Trigger Circuit, Foot Brake

Switch, Siren and System Ground).

C5: GREEN/RED – Window Close Output Neg. (-). Connect the GREEN/RED wire to a window close module (not

included) Neg. (-) input. Follow the window close module instructions for wiring to window motors. Do not connect

this wire directly to the vehicle's window close switch.

C5: PURPLE – Trunk Release Output Neg. (-). Connect the PURPLE wire to the trunk release Neg. (-) trigger wire

on the vehicle's trunk release relay. In the event that a trunk release is to be added to the vehicle, an additional relay

and trunk release solenoid will be required.

C5:BLACK/YELLOW –Triggered Alarm Output (-). Use this output to turn on any device that may be used to

identify when the alarm has been triggered. i.e. additional horns, lights, etc. that will turn ON only when the alarm is

triggered. An additional relay may be required if the current load exceeds 150MA.

C5: BLACK/WHITE – Neg. (-) Door Trigger switch Input. Connect the BLACK/WHITE wire to the Neg. (-) Door

Trigger switch. If the vehicle has "+" Pos Door Trigger input use the BLUE wire from connector C7.

C5: PINK - (+12v) Foot Brake Switch Input Used for door lock and Starter enable input. Connect to Foot brake

switch terminal that has +12v only when foot brake is depressed.

C5: ORANGE: - Siren +12v Output. Connect to the RED Siren wire. Connect the second siren input (BLACK wire)

to a good chassis ground. If the vehicle's horn is used connect the ORANGE wire to the (+) on the horn relay.

C5: BLACK – Neg. (-) Ground Connection. Connect the BLACK wire to a good chassis ground in a convenient

location.

Installing Connector C6:

3 PIN Wire Harness

("Push Start Stop" Button)

The "PUSH START STOP" button can be surface mounted in a convenient location on the dash or can be mounted

using the supplied adjustable bracket for mounting under the dash or on the console. The high strength double stick

adhesive disk is to be used on the back side of the switch with both mounting methods. Make certain that the back

of the button and the mounting surface is thoroughly cleaned with isopropyl alcohol to remove any dirt, grease or

vinyl dressing materials. DO NOT use acetone, MEK, lacquer thinner or any other harsh chemicals as they will

destroy paint, vinyl and plastic. The adhesive will not come loose or degrade as long as the surface has been

cleaned thoroughly. Attach the adhesive disk to the back of the button first.

If you choose to mount the button on the dash with the wire hidden behind the button then drill a 3/8" dia. hole in a

location where the small wire and connector can be fed through the dash. Rout the "PUSH START STOP" button

wire to the module. Connect the White 3 terminal connector to the module. The connector is indexed so that it can

only be installed in one direction.

Installing Connector C7:

4 Pin Wire Harness ( Start enable & Disarm Output)

C7: BLUE – Pos. (+) Door Switch Input. Connect the BLUE wire to a Pos. (+) Door Trigger switch. If the vehicle

has "-" Neg. Door Trigger input use the BLACK/WHITE wire from connector C5.

C7: YELLOW – Start Enable Input.

For Automatic Transmission: Connect the YELLOW wire to a good chassis ground (-).

- 13 -

Rev. V8.2- 20212