Gama Garden GCS-2200E Manual de instruções - Página 10
Procurar online ou descarregar pdf Manual de instruções para Motosserra Gama Garden GCS-2200E. Gama Garden GCS-2200E 18 páginas. Electric chain saw
Imprimir páginacontents of the oil tank during sawing work by
checking the oil gauge (C). Close the oil tank cap
tightly and wipe away any spills.
The chainsaw is supplied without oil in tank and it
must fill up when first operation. The tank capacity
is
approx.
150 ml
lubrication oil.
Assembling bar & sawchain
The chainsaw must be unplugged.
To prevent injury on the sharp cutting edges,
always wear gloves when assembling, tensioning
and checking the chain.
The guide bar and saw chain are supplied
separately when packing. To assemble, first
unscrew the lock knob (G) and remove the guide
bar cover (E).
Before assembling the guide bar with the saw
chain, check the cutting direction of the teeth!
The running direction is marked with an arrow on
the cover (D). To determine the direction of cut, it
may be necessary to turn over the saw chain (A).
Hold the guide bar (B) vertically with the tip
pointing upwards and put on sawchain at the tip
of the bar.
Then assemble the guide bar with the saw
chain as follows:
Place the saw chain round the chain wheel (C)
•
and make sure it is correctly mounted,
Place the guide bar with the saw chain on the
•
lock bolt (H),
Place the cover (E) on top and tighten gently
•
with the lock knob (F) clockwise.
Now the saw chain has to be correctly tensioned.
Tensioning the saw chain
Always pull the plug out of the power socket
before doing any work on the chainsaw!
Wear safety gloves!
Make sure the saw chain (A) is inside the guide
groove of the guide bar!
Turn clockwise of the tension knob (G), the guide
bar is being pushed forwards until the saw chain
is correctly tensioned. Do not tension the chain
too tightly. When cold, it should be possible to lift
the chain in the middle of the guide bar approx. 5
using
low
viscosity
(Fig 3)
mm. Tighten the lock knob (F) securely.
When warm, the saw chain will expand and
slacken and there is a danger of it jumping off the
rail altogether. Re-tension if necessary. If the saw
chain is re-tensioned when hot, it must be
loosened again when the sawing work has been
completed. Otherwise, the contraction which
takes place as the chain cools would result in
excessively high tension. A new saw chain
requires a running-in period of approx. 5 minutes.
Chain lubrication is very important at this stage.
After running in, check chain tension and
re-tension if necessary.
Securing the extension lead
Only use extension leads suitable for outdoor use.
The cross section of the cable (max. length of
extension cord: 75m) must be at least 1,5 mm2.
Secure the chainsaw flex to the extension lead by
inserting the extension lead into the strain relief gap
of the housing.
Extension leads longer than 30 m will reduce the
performance of the chainsaw.
Chain lubrication
To prevent excessive wear, the saw chain and
guide bar must be evenly lubricated during
operation.
Lubrication is automatic. Never work without
chain lubrication. If the chain runs dry, the entire
cutting apparatus will quickly become severely
damaged. It is therefore important to check both
chain lubrication and the oil gauge every use (Fig.
2).
Never use the saw when the oil level is below the
"MIN." mark.
When only approx. 10 mm of oil is visible at the
lower rim of the oil gauge (C), you must top up
with oil.
Checking the automatic lubrication
Before commencing work, check the automatic
chain lubrication and oil gauge. Switch on the
chain saw and hold it above the ground. Be
careful not to allow the chain saw to touch the
ground. For safety reasons it is best to keep a
10
10
(Fig 4)