HIKOKI FD 10SA Manual de Instruções de Manuseamento - Página 5
Procurar online ou descarregar pdf Manual de Instruções de Manuseamento para Perfurar HIKOKI FD 10SA. HIKOKI FD 10SA 20 páginas.
Imprimir página
○ When drilling a through hole in lumber, remove the
drill from the material as soon as the tip of the drill
bit protrudes from the opposite surface. Then, turn
the workpiece over and complete the drilling from
the opposite side to obtain a clean hole. (Fig. 4)
If extra lumber is applied under the lumber you want
to drill and it is drilled together, a fi ne hole will also
be made. (Fig. 5)
○ A wood-working drill need not be pressed strongly
since it penetrates using the screw at the point.
Even if excessive force is used, a hole will not be
made quickly.
2 To use for drilling metal
○ In case you drill metal with an iron-working drill,
apply in advance a center punch in the drilling
position. You can drill metal stably since the point of
the drill does not slip.
○ If you apply sewing machine oil or soapy water to
the drill with a brush or an old tooth brush, the drill
will last long.
○ Even if more-than-necessary force is used, a hole
will not be made quickly.
On the contrary, the edge of the drill will be
damaged. This will decrease operational effi ciency
and shorten the life of this too.
CAUTION
Do not expose the motor to water as it may cause
motor malfunction and electric shock.
5. To use the driving wood screws (FD10VA)
(1) Driver bit
○ For driving a minus wood screw, the driver bit
detaches easily. So use wood screws with a plus
groove as often as possible.
○ Select a driver bit matching the plus groove and the
minus groove of the wood screw.
(2) Pilot hole
If a pilot hole is made with a drill a little thinner than
the diameter of the wood screw, the lumber will
not be split and the wood screw will be driven with
ease.
(3) Driving operation
Put the wood screw lightly in the pilot hole, apply the
bit to the groove, turn on the switch and drive the
screw.
6. Caution to be taken immediately after operation
When placing the drill in dusty places before the
rotating parts has stopped completely, make sure
the machine does not suck in dust and swarf.
MAINTENANCE AND INSPECTION
CAUTION
Be sure to switch power OFF and disconnect the
plug from the receptacle during maintenance and
inspection.
1. Inspecting the drill bit and driver bit
Since use of an abraded drill bit will cause motor
malfunctioning and degraded effi ciency, replace
the drill bit with a new one or resharpening without
delay when abrasion is noted. If you use a driver bit
of which point is worn or broken, it will be dangerous
since it slips. So replace it with a new one.
2. Inspecting the mounting screws
Regularly inspect all mounting screws and ensure
that they are properly tightened. Should any of the
screws be loose, retighten them immediately. Failure
to do so could result in serious hazard.
3. Servicing
Consult an authorized Service Center in the event of
power tool failure.
4. Service parts list
A: Item No.
B: Code No.
C: No. Used
D: Remarks
CAUTION
Repair, modifi cation and inspection of HiKOKI Power
Tools must be carried out by a HiKOKI Authorized
Service Center.
This Parts List will be helpful if presented with the
tool to the HiKOKI Authorized Service Center when
requesting repair or other maintenance.
In the operation and maintenance of power tools, the
safety regulations and standards prescribed in each
country must be observed.
MODIFICATIONS
HiKOKI Power Tools are constantly being improved
and modifi ed to incorporate the latest technological
advancements.
Accordingly, some parts (i.e. code numbers and/or
design) may be changed without prior notice.
NOTE
Due to HiKOKI's continuing program of research and
development, the specifi cations herein are subject to
change without prior notice.
English
4