JADO 853/453 Series Instruções de instalação - Página 2

Procurar online ou descarregar pdf Instruções de instalação para Luminárias de casa de banho JADO 853/453 Series. JADO 853/453 Series 2 páginas. Pressure balanced shower with check stops, classic, colonial, victorian

Imprimir página

TOOLS REQUIRED

Channel Locks

Tubing Cutter

Adjustable Wrench

ROUGHING-IN DIMENSIONS

To assure proper positioning in relation to wall,

note roughing-in dimensions.

1-5/8" TO 3-1/4"

FINISHED WALL

1/2" NPT

OPTIONAL TO

FINISHED

FLOOR

USUALLY

BETWEEN

72'' AND 84"

7-1/2" REF.

"SEE ILLUSTRATION"

74" FOR HEAD

CLEARANCE

(OPTIONAL)

SHW

7-7/8"

TUB

48" TO 54"

OPTIONAL

1/2" PLUG

BOTTOM OF

TUB

OR SHOWER

STALL

INLETS 1/2" NPT

5-7/8"

OUTLETS 1/2" NPT

3-3/8"

THREADED INLETS (STOPS)

CAUTION: Protect finish on SHOWER ARM

INSTALL TRIM

and SHOWER HEAD when installing.

Push CAP (1) onto VALVE CARTRIDGE (2). Secure CAP (1) to

VALVE CARTRIDGE (2) with SCREW (3) for LEVER HANDLE only.

(Spline in CAP (1) must fully engage spline on cartridge stem).

Mount ESCUTCHEON (5) with gasket to valve body and secure

with SCREWS (6).

Push the COVER (7) as shown over the CAP (1) and align

prongs on COVER (7) with screw holes in ESCUTCHEON (5).

Important! Make sure COVER (7) snaps over the SCREWS (6).

Remove PIPE CAPS (8) from shower pipe.

Install SHOWER ARM (9) and SHOWER HEAD (10)

INSTALL HANDLE (ADJUST HOT LIMIT STOP PRIOR

TO HANDLE INSTALLATION, SEE STEP 3)

For Cross Handle: Thread HANDLE BASE (11) onto threads

of CAP (1) until seated against it's internal stop.With VALVE

in off position align CROSS HANDLE (12) as desired. Install

CROSS HANDLE (12) onto VALVE STEM (13) and tighten

HANDLE SCREW (14). Thread INDEX (15) into

CROSS HANDLE.

Lever Handles: Thread HANDLE BASE (16) onto

threads of CAP (1) until seated against it's internal

stop. Install FRICTION WASHER (17) onto base

of LEVER HANDLE (18). Align LEVER HANDLE (18)

and tighten set screw with HEX WRENCH (4)

supplied with faucet to secure handle.

Plumbers' Putty or Caulking

Teflon Tape

ROUGHING-IN

CAUTION

Turn off water at main supply.

NOTE

When soldering, remove PLASTER GUARD, CARTRIDGES and CHECK

STOPS (IF PRESENT). When finished soldering, flush valve body, replace

cartridges, check stops (if present) and plaster guard to continue installation.

Use thread sealant or Teflon tape on threaded connections.

See Roughing-in diagram before starting.

Connections are:

1/2" female NPT for threaded inlets

Connect RISER PIPE (1) to MANIFOLD (2)

top outlet marked "SHR".

Plug TUB outlet with 1/2" NPT PLUG supplied.

For proper positioning the finished wall

must be within side wall of PLASTER

GUARD (4).

If the valve is installed on a fiberglass or

other thin wall application, the PLASTER

GUARD (4) can be used as a support.

Cut a 4" dia. hole in the shower stall.

Drill two additional 1" holes to allow

HOT

access to the stops.

Remove PLASTER GUARD (4), rotate

180˚ so that indicated screw holes fit

MANIFOLD (2). Push CAP on valve, place

ESCUTCHEON on and attach with screws.

PLUG

Connect hot and cold water supplies.

Cap off shower pipe (5).

For support, use pipe BRACES (6) secured to wooden braces.

With valve turned off, turn on water supplies. Check for leaks.

THREADS

ON CAP

CROSS HANDLE

LEVER HANDLES

ADJUST HOT LIMIT STOP (MUST BE DONE PRIOR TO TRIM INSTALLATION)

Phillips Screwdriver

By restricting HANDLE rotation and limiting the amount of hot water allowed to mix with the cold, the HOT LIMIT

SAFETY STOP (1) reduces risk of accidental scalding. To set the maximum hot water temperature of your faucet, all

Regular Screwdriver

you need to do is adjust the setting on the HOT LIMIT SAFETY STOP (1).

Turn CARTRIDGE STEM (2) to the OFF position (coldest setting) before making adjustment to HOT LIMIT STOP (1). Use

a flat blade screwdriver to pry free the HOT LIMIT SAFETY STOP (1). Pull forward and rotate counterclockwise one number

to limit hot water temperature. Use ARROW (3) on CARTRIDGE (4) and NUMBERS (5) on HOT LIMIT STOP (1) for indication.

COLD

TEST INSTALLED FITTING

Turn VALVE "off".

With HANDLE (1) in "off" position, turn on water supplies and check all

connections for leaks.

Operate HANDLE (1) and flush water lines thoroughly. Check SHOWER (2) for

proper operation.

Check SHOWER connections for leaks.

BACK TO BACK INSTALLATION (SEE ILLUSTRATION STEP 6 FOR REFERENCE)

Remove Handle and Trim from Valve. See step 1 for reference.

Remove PRESSURE BALANCE UNIT (5). Rotate PRESSURE BALANCE UNIT (5) 180˚ so that the inlets face up and the

large outlet port faces down.

Push PRESSURE BALANCE UNIT (5) in casting make sure inlets line up with holes in bottom of casting. Top flange should

butt up against top of casting.

Reassemble FIXATION RING (4) and CARTRIDGE (1).

1 0 9 4 6 2 A

HOTTER

(Smaller Numbers)

0 1 3 5 7 9 11 13 15

COLDER

(Larger Numbers)

0 1 3 5 7 9 11 13 15

1 0 9 4 6 2 A