Airflex5D ZAF-PJM4 Manual de instalação e montagem - Página 3

Procurar online ou descarregar pdf Manual de instalação e montagem para Acessórios para projectores Airflex5D ZAF-PJM4. Airflex5D ZAF-PJM4 9 páginas. Universal projector ceiling mount with polarized lens filter clip

Imprimir página
N  
M6*30   r ound   s crew   k nob  
M  
End   c ap  
O  
Sliding   p late  
P  
M5*18mm   r ound   h ead   s crew  
Q  
Upper   s upport   h ook  
 
Note:   R ead   e ntire   i nstructions   b efore   s tarting   i nstallation   a nd   a ssembly   o f   t he   m ount.  
-­‐
Do   not   begin   installation   of   the   product   until   you   have   fully   read   and   understood   the   instructions   and  
warnings   c ontained   i n   t his   g uide.  
-­‐
This   product   should   only   be   installed   by   someone   with   good   mechanical   skills,   has   experience   with   basic  
building   c onstruction,   a nd   f ully   u nderstands   t hese   i nstructions.  
-­‐
Make   sure   that   the   supporting   surface   will   safely   support   the   combined   load   of   the   equipment   and   all  
attached   h ardware   c omponents.  
-­‐
Never   e xceed   t he   m aximum   l oad   c apacity  
-­‐
Always   u se   a n   a ssistant   o r   m echanical   l ifting   e quipment   t o   s afely   l ift   a nd   p osition   e quipment.  
-­‐
This  product  is  intended  for  indoor  use  only.  Use  of  this  product  outdoors  could  lead  to  product  failure  and  
personal   i njury.  
-­‐
Tighten  screws  firmly,  but  do  not  overtighten  to  avoid  stripping  the  screws.     Overtightening  the  screws  can  
also   d amage   t he   i tems   a nd   g reatly   r educe   t heir   h olding.  
-­‐
When  installing  or  adjusting  the  ceiling  mount,  do  not  use  adhesives,  lubricants,  or  oils  to  prevent  the  screws  
from  loosening.  If  you  use  adhesives,  lubricants,  or  oils  to  prevent  the  screws  from  loosening,  the  casing  may  
crack   a nd   t he   p rojector   m ay   f ail,   c ausing   s erious   i njury   a nd   d amage   t o   t he   p rojector.  
 
Projector   M ount   A ssembly  
 
 
1.  Loosen  the  hex  screws  on  the  
 
pan/tilt   and   remove   from   the  
 
upper   s upport   h ook.  
 
 
 
 
 
 
2.   A ttach   a nd   s ecure   t he   p an/tilt  
to   t he   p rojector   b ase   p late   u sing  
 
the   M 8*16   h ex   s crews.  
 
 
 
 
4  
8  
A4  
2  
4  
A5  
2  
4  
A6  
4  
8  
A7  
2  
4  
A8  
WARNING
www.Airflex5D.com   |  
i
M5   w asher  
Hanging   a ngle  
Metal   c lip  
Projector  
Polarized   F ilter  
 
3.   Attach   the   flexible   metal   clip  
filter   h older   w ith   t he   M 8   l ocknut.  
4  
8  
8  
16  
2  
4  
2  
4  
2  
4