Britax ADVANSAFIX II SICT Instruções para o utilizador - Página 2

Procurar online ou descarregar pdf Instruções para o utilizador para Assento para automóvel Britax ADVANSAFIX II SICT. Britax ADVANSAFIX II SICT 2 páginas.

Imprimir página

Britax ADVANSAFIX II SICT Instruções para o utilizador

1. GENERAL SAFETY NOTES

2. USE IN THE VEHICLE

Please observe the instructions on the use of child restraint systems described in

Take the time to carefully read through these instructions, and always

your vehicle owner's manual.

keep them ready to hand in the designated pocket on the child seat.

The seat may be used in vehicles equipped with ISOFIX, Top Tether anchoring

systems and 3-point belt (see type list). Please consult your vehicle owner's

For the protection of all vehicle occupants

manual for information about the ISOFIX &Top Tether anchoring points and the

In the case of an emergency stop or an accident, persons or objects which are

installation with 3-point belt. Also check your vehicle owner's manual for seats

not properly secured in the car can cause injury to other vehicle occupants.

which are approved for child safety seats in the weight classes 9-18 kg, 15-25 kg,

For this reason, please always check that:

22-36 kg.

• the backrests of the vehicle seats are locked (e.g. that the latch on a folding

You can use your child car seat as follows:

rear seat bench is engaged).

• all heavy or sharp-edged objects in the vehicle (e.g. on the parcel shelf) are

In the direction of travel

secured.

• all persons in the vehicle have their seat belts fastened.

Against the direction of travel

• the child safety seat is always secured in the car via the ISOFIX anchoring,

with 2-point belt (Vehicle belt)

the Top Tether and the 3-point belt (Vehicle belt), even when there is no child

On seats featuring:

in the seat

ISOFIX attachments (between seat surface and back-

For the protection of your child

rest), Top Tether anchoring points (for example on the

• The more snugly the harness fits over your child's body, the safer your child

parcel shelf, on the floor or behind the backrest) and

will be.

3-point belt (Vehicle belt)

• Please do not ever leave your child unattended in the child safety seat in the

(Please observe the applicable regulations in your country)

vehicle.

1) Use is permitted on a rearward-facing vehicle seat (e.g. in a van or minibus) only if

• Use on the rear seat:

the vehicle seat is also approved for use by adults. The seat must not be positioned

Move the front seat forward far enough that you child's feet cannot hit the

anywhere where it is in range of an airbag which is being deployed.

backrest of the front seat (to prevent risk of injury).

2) The safety belt must be approved to ECE R 16 or a comparable standard (see test

• The child safety seat can get hot in direct sunshine. Caution: Children's

label on belt with an "E" or "e" in a circle).

skin is delicate and could be injured as a result. Protect the child seat against

3) If there is a front airbag: Slide the passenger seat a long way back and refer to any

intensive direct sunlight when it is not currently in use.

instructions in vehicle owner's manual.

• Only allow your child to enter and exit the vehicle on the pavement side.

• Make stops during longer journeys to give your child an opportunity to run

about and play.

To protect your vehicle

Some vehicle seat coverings made of more delicate materials (e.g. velour,

leather, etc.) may develop wear marks when child seats are used. For optimum

protection of your seat covers, we recommend using the BRITAX Car Seat

Protector, which is available from our range of accessories.

09. REMOVING THE 5-POINT HARNESS& & REFITTING THE SECUREGUARD

1. Put the storage bag

7. Pull below both, the shoulder pads

forward over the seat.

2. Loosen the 5-point harness

of the child seat as much as possible.

through the slots

Back side of the child seat:

8. Slide the belt loops off of the plastic extensions

3. Press the button of the shoulder belt height adjuster

at the rear of the seat shell

and tilt the shoulder belt height adjuster

towards you.

Front side of the child seat:

4. Move the shoulder belt height adjuster

into the top position and fix the position

Pull out the adjuster strap

by releasing the button of the shoulder belt height adjuster.

10. Store the adjuster strap in the adjuster housing

5. Loosen the 5-point harness

of the child seat as much as possible. Unhook the

11. Pull the shoulder pads

shoulder belts

on the back side of the child seat from the connecting piece

12. Remove the shoulder pads

6. Snap the connecting piece

in the provided storage.

storage bag on the rear of the seat.

10. REFITTING THE 5-POINT HARNESS & REMOVING THE SECUREGUARD

1. Grasp the SecureGuard metal plate

from underneath and turn it into a vertical

4. Squeeze the adjustment handle

position.

rest into the lowest position.

2. Push upwards and slide the metal plate

through the slot

5. Release the adjustment handle

3. Remove the SecureGuard

and store it in the storage bag

6. Lift the lower part of the headrest cover and place it over the headrest

7. Open the left and right buttons on the lower part of the cover

piece on the seating area.

8. Take the shoulder belts

and unroll the shoulder belts.

9. Fold back the two cover pieces and close the left and right poppers

part of the cover.

3. APPROVAL

BRITAX

child safety seat

ADVANSAFIX II / ADVANSAFIX II SICT

*ECE = European Standard for Child Safety Equipment

Yes

The child safety seat has been designed, tested and certified according to the require-

ments of the European Standard for Child Safety Equipment (ECE R 44/04). The test

mark E (in a circle) and the certification number are located on the orange certification

sticker (sticker on the child safety seat).

• This certification will be invalidated if you make any modifications to the child safety

seat.

• The ADVANSAFIX II / ADVANSAFIX II SICT child safety seat must only be used to

Yes

2) 3)

secure your child in the vehicle. It must never be used as a seat or toy in the home.

Risk of injury due to unauthorised modifications!

Unauthorised technical modifications may reduce or entirely void the seat's protective

properties.

• Do not make any technical modifications to the child seat.

• Use the child seat only as described in these user instructions.

The ADVANSAFIX II / ADVANSAFIX II SICT is approved for one method of installation:

Group

Installation method

1 (9-18 kg)

ISOFIT + TopTether +

Vehicle belt

2 (15-25 kg)

ISOFIT+ TopTether +

Vehicle belt

2 (15-25 kg)

ISOFIT + TopTether

3 (22-36 kg)

ISOFIT + TopTether

and the two shoulder belts

to the front

13. Open the harness buckle

(press the red release button)

(front side of the child seat).

14. Lift the lower part of the rear cover to the top and place it over the headrest.

of the shoulder belt height adjust-

15. Open the left and right poppers

cover piece to the front. Slide the buckle latches

ments.

as far as possible.

16. Roll the shoulder belts

together and place them also into the storage compart-

ments.

through the slots

to the front.

17. Repositon the two cover parts to the rear and lock the poppers

from the shoulder belts

and put them in the

right side of the cover back side.

at the rear of the headrest

and push the head-

Should the child seat not be in the most reclined position:

Press the recline handle so that the seat is in its most upright position.

to lock into place.

10. Lift the harness buckle

and the shoulder pads

the back side of the seat.

11. Refitting harness buckle

and lay the cover

and crotch pad

ing area towards you. Use the belt slot closest to the backrest

and the buckle latches

from the storage compartment

12. Take the harness buckle

and hold the metal plate

narrow side upwards through the belt slot

on the lower

13. Ensure by looking underneath the seat that the metal plate

tion and check the installation by pulling on the harness buckle

14. Guide the two buckle latches

4. CARE AND MAINTENANCE

Care for the harness buckle

Tested and certified according

It is vital for the safety of your child that the harness buckle works correctly. Malfunctions

to ECE* R 44/04

of the harness buckle are usually caused by accumulations of dirt or foreign bodies.

Malfunctions are as follows:

Group

Body weight

• The buckle latches are ejected only slowly when the red release button is pressed.

9 to 18 kg

• The buckle latches will no longer lock home (i.e. they are ejected again if you try to

push them in).

15 to 25 kg

• The buckle latches engage without an audible „click".

22 to 36 kg

• The buckle latches are difficult to insert (you feel resistance).

• The buckle only opens if extreme force is applied.

Remedy

wash out the harness buckle so that it functions properly once again:

Cleaning the harness buckle

1. Open the harness buckle

(press the red button).

2. Open the Velcro fastener on the crotch pad

cover.

Child installation

User Guide

3. Put the seat shell into the recline position

chapter

4. Grasp the metal plate

from underneath and turn it into a vertical position

with 5-point harness

5. Slide the metal plate

through the slot

6. Remove the harness buckle

7. Soak the harness buckle

in warm water with washing-up liquid for at least an

with 5-point harness

hour

8. Then rinse and dry it thoroughly.

Vehicle belt

Cleaning

Vehicle belt

CAUTION Please be sure to use only genuine Britax replacement seat covers, as

the seat cover is an integral part of the child safety seat which plays an important role

in ensuring that the system works properly. Replacement seat covers are available from

18. Lift the recline handle and pull at the front to fully recline the child seat.

19. Pull the elastic strip

over the harness buckle

20. Grasp the metal plate

from underneath and turn it into a vertical position.

on the lower part of the cover

and lift the

21. Push upwards and slide the metal plate

through the slot

down into the storage compart-

22. Remove the harness buckle

with the crotch pad

bag

on the left and

into the harness buckle

- this should make a click noise.

CAUTION! The lap belts must not be twisted or swapped.

from the storage bag

15. Thread the shoulder pads

onto the shoulder belts

as shown ensuring there are no twists. Align the two loops of the shoulder belts

: pull the elastic strip

in the seat-

and strap loops of the shoulder pads

16. Pull the shoulder belts

and the strap loops of the shoulder pads

vertically. Push it with the

slots

to the seat shell from above.

ip: Fold up the rear cover part.

is in a horizontal posi-

several times.

together and engage them before putting them

your retailer.

CAUTION! The child seat must not be used without its cover.

• The cover can be removed and washed with a mild detergent using the

washing machine's cycle for delicate items (30 °C). Please observe the

instructions on the washing label of the cover.

• The plastic parts (including the SecureGuard) can be cleaned using soapy water. Do

not use harsh cleaning agents (such as solvents).

• The harnesses can be washed in lukewarm soapy water.

CAUTION! Never remove the buckle latches

from the straps.

• The shoulder pads can be washed in lukewarm soapy water.

Removing the cover

A) Headrest

1. Move the headrest of the child seat to the upper position.

2. Take the elastic seam of the cover

from the hooks at the back side of the headrest

and remove the cover of the headrest.

and take off the crotch pad from the

B) Cover

1. Undo the hooks on the bottom side.

2. Undo the hooks located on the upper back side.

3. Undo the elastic loop on both sides of the belt guides.

4. Open the two plastic fasteners on the back side of the cover.

5. Remove the cover.

Re-fitting the Cover:

Simply follow the steps in the opposite order.

CAUTION! Never use the child seat in installation method A without a correct

installed buckle. Make sure that the metal plate

is correctly attached.

CAUTION! Check that the harness straps are not twisted and that they

have been correctly inserted in the belt slots on the cover.

23. Take the SecureGuard

from the storage bag and hold the metal plate

vertically. Push it with the narrow side upwards through the belt slot

you into the seat shell from above.

24. Ensure by looking underneath the seat that the SecureGuard metal plate

and store it in the storage

a horizontal position and check the installation by pulling on the SecureGuard

several times.

17. Pull the strap loops of the shoulder pads

onto the plastic extensions

shoulder belt height adjuster

.Tip: the strap loops of the shoulder pads should

in the correct orientation

be the lower loop.

18. Fold the upper part of the cover downwards.

CAUTION! The shoulder belts

must not be twisted or swapped.

through the

19. Take the connecting piece

from the provided storage on the back side of the

child seat.

20. Hook the shoulder belts

back onto the connecting piece

the left arm of the connecting piece and the right loop on the right arm.

21. Pull slowly on the adjustment strap

and at the same time push the connecting

piece

between backrest and the provided storage of the connecting piece.

BRITAX RÖMER

Kindersicherheit GmbH

t: +49 (0) 731 9345-199/-299

Blaubeurer Straße 71

f: +49 (0) 731 9345-210

D-89077 Ulm

e: [email protected]

Germany

www.britax.com

BRITAX EXCELSIOR LIMITED

1 Churchill Way West

t: +44 (0) 1264 333343

Andover

f: +44 (0) 1264 334146

Hampshire SP10 3UW

e: [email protected]

United Kingdom

www.britax.com

9 – 36 kg

9 m ~ 12 y

ADVANSAFIX II

closest to

ADVANSAFIX II SICT

is in

User instructions

of the

. The left loop on