CenturionPro XL MEGABUCKER Manual do Proprietário - Página 10

Procurar online ou descarregar pdf Manual do Proprietário para Equipamento agrícola CenturionPro XL MEGABUCKER. CenturionPro XL MEGABUCKER 12 páginas.

Imprimir página

HEMP & CANNABIS

HARVESTING

SOLUTIONS

TROUBLE SHOOTING

1) MOTOR IS VERY HOT

The motor is designed to operate at higher temperatures, avoid contact with the motor during regular operation. The motor is thermally fused and will shut down automatically if overheating occurs

2) MACHINE IS JAMMED, OR MISFED WITH PLANT MATTER

Occasionally stems or shoots may become wrapped around rollers and can pack up behind the face plate of the machine. If this occurs, the machine may labor to operate or stop the rollers completely due

to an overloaded condition. To remedy this problem we recommend the machine be powered down and electrically locked out. The face plates can then be removed and the jammed stems cleared. Once

cleared, replace all faceplates and guards before unlocking and re-engaging power to the machine for further operation.

3) THERE IS A GRINDING SOUND COMING FROM THE MACHINE

This can be caused by worn out bearings, misaligned gears or improperly installed components. If the pull-wheels were recently replaced / cleaned; then it is likely an alignment issue, otherwise the

bearings are damaged and need replacement.

4) THE PULL FORCE SEEMS WEAK

This could be caused by excessive debris build-up in the rollers. Disassemble, clean and inspect machine to determine the issue.

5) ROLLERS ARE SLIPPING

Slipping occurs if the motor reaches it's torque limit, or the roller friction has been reduced. Roller friction can be reduced by feeding excessively wet material or if any lubricants accidentally get on the

roller. Check to see if the rollers are dry and clean.

When using the machine with freshly harvested or "wet" product, the rollers may become loaded with residue and lose their ability to grab and pull stems or shoots through the faceplate nozzles. Likewise, if the

same exact nozzle is used repeatedly by an operator, buildup of residue will occur on the roller segment at that specific nozzle. Therefore, we recommend operators vary the use of the different nozzles presented

to them as they work. When harvests are made in the rain, it is best to remove the excess water from the stems or shoots before being fed to the machine, to decrease roller wetness and increase efficiency.

6) WHAT SPEED SHOULD I USE FOR WET MATERIAL?

We recommend a faster speed for wet product and a slower speed for dry.

7) DOES THE STEM HAVE TO BE A CERTAIN LENGTH TO FEED TO THE BUCKER?

Yes, there must be 3 inches of base stem to clear the cutters.

8) DO I NEED A SPECIAL OUTLET FOR THE BUCKER?

CenturionPro Buckers can be plugged into any standard 110V wall outlet (220V AUS/EU).

9) DOES THE XL MEGABUCKER WORK BEST WITH A PARTICULAR STRAIN?

XL MegaBuckers can handle any strain, but please note that all strains run differently and denser strains may need the top colas taken off before being run.

FREQUENTLY ASKED QUESTIONS

HOW EASY IS IT TO CLEAN?

Our machines can be taken apart and cleaned within 10-15 minutes. The Bucker must be cleaned after daily use. Just spray the rollers liberally with isopropyl alcohol, then wipe with a soft cloth. We recommend to clean

every 4-6 hours of use, but it depends on your strain. We know the importance of down time during a harvest so we wanted to make this process extremely quick and easy

DO YOUR MACHINES WORK ON WET OR DRY MATERIAL?

All CenturionPro Buckers can run both wet and dry to fit your processing needs.

ARE YOUR MACHINES BUILT TO AN INDUSTRIAL STANDARD?

We do not compromise quality for cost savings. All CenturionPro Solutions machines are composed of the highest quality materials available and each machine is put through a comprehensive quality control inspection.

We only use brand name components in the build out of our machines which enables us to have the comfort in giving you an industry leading warranty on all machines. With proper maintenance these machines will

last you for years to come.

WHAT IS THE OPTIMAL ROOM TEMPERATURE TO TRIM?

Use your CenturionPro Bucker in 50-60 °F (10- 15 °C) room to get the best performance. Cooler temperatures prevent excessive sticking to machine components.

MY MACHINE IS NOT WORKING LIKE IT DID WHEN IT WAS NEW, WHY?

Make sure to fully clean the machine and rollers. If the machine is clean and the rollers are free of debris, then your machine should buck exactly like it was new.

WE ARE OPEN MONDAY THROUGH FRIDAY FROM 9AM TO 5PM PST - PH: 1-855-535-0558

FILLING OUT THE "CONTACT US" FORM ON THE WEBSITE, IS ANOTHER SURE WAY TO GET IN TOUCH.

1 855 535 0558

cprosolutions.com