IKEA NUTID Manual de instruções de instalação e utilização - Página 7
Procurar online ou descarregar pdf Manual de instruções de instalação e utilização para Frigorífico IKEA NUTID. IKEA NUTID 46 páginas. French door refrigerator
Também para IKEA NUTID: Manual de instalação (16 páginas), Manual de instalação (12 páginas), Manual de instruções de montagem (12 páginas)
Imprimir página
TOOLS NEEDED: 5⁄16", 3⁄8", 1⁄4" hex head socket wrench,
a #2 Phillips screwdriver, and a flat-blade screwdriver.
IMPORTANT:
Your refrigerator may have a standard reversible refrigerator
■
door with either a freezer door or freezer drawer, or French
doors. Follow the instructions specific to the door style of
your model.
All graphics referenced in the following instructions are
■
included later in this section after "Final Steps." The
graphics shown for the standard door are for a right-hand
swing refrigerator (hinges factory installed on the right).
If you only want to remove and replace the doors, see
■
"Remove Door(s) and Hinges" and "Replace Door(s) and
Hinges."
Before you begin, turn the refrigerator control OFF, and
■
remove food and adjustable door or utility bins from the
doors.
Remove and Replace Handles
Style 1
1. Using a 3⁄32" or 1⁄8" hex key, loosen the two setscrews
located on the side of each handle. See Style 1 Handle
graphics 2 and 4.
2. Pull the handle straight out from the door. Keep the screws
for reattaching the handles.
3. To replace the handles, reverse the directions.
Style 2
To Remove Handles:
1. Grasp the lower part of the handle firmly. Slide the handle
up and pull the handle straight out from the door. See Style
2 Handle graphics 2 and 4.
To Replace Handles:
1. Position the handle so that the large holes in the mounting
clips are down and align the holes with the door studs.
2. Rotate the handle so that the mounting clips are flat against
the door and slide the handle down to engage. See Style 2
Handle graphics 2 and 4.
Remove Doors and Hinges
Standard Door
Hex-Head Top Hinge Screw
1. Unplug refrigerator or disconnect power.
2. Keep the refrigerator door closed until you are ready to lift it
free from the cabinet.
NOTE: Provide additional support for the door while the
hinges are being moved. Do not depend on the door gasket
magnets to hold the door in place while you are working.
3. Remove the parts for the top hinge as shown in Top Hinge
graphic. Lift the refrigerator door free from the cabinet.
4. Remove the parts for the bottom hinge as shown in Bottom
Hinge graphic.
Refrigerator Door(s) and Drawer
French Doors
WARNING
Electrical Shock Hazard
Disconnect power before removing doors.
Failure to do so can result in death or electrical shock.
1. Unplug refrigerator or disconnect power.
2. Keep the freezer door closed until you are ready to lift it free
from the cabinet.
NOTE: Provide additional support for the door while the
hinges are being moved. Do not depend on the door gasket
magnets to hold the door in place while you are working.
3. Starting with the right-hand side door, remove the parts
for the top hinge as shown in Top Hinge graphic. Lift the
refrigerator door from the bottom hinge pin.
4. Remove the hinge pin cover from the bottom hinge pin and
keep it for later use. See Bottom Hinge graphic.
5. Before removing the left-hand side door, disconnect the
wiring plug located on top of the top hinge by wedging a
flat-blade screwdriver or your fingernail between the two
sections. See Wiring Plug graphic.
NOTE: The green, ground wire remains attached to the
hinge.
6. Remove the parts for the left-hand side door top hinge
as shown in the Top Hinge graphic. Lift the door from the
bottom hinge pin.
NOTE: Remove the hinge pin cover from the bottom hinge
pin and keep it for later use. See Bottom Hinge graphic.
Reverse Door - Standard Door (optional)
IMPORTANT: If you want to reverse your door so it opens from
the opposite side, follow these steps. If you are not reversing
the door, see "Replace Door(s) and Hinges."
Door Stop Screw
Flat-Head Handle Screw
Cabinet
1. Remove hinge screws from handle side and move them to
opposite side. See Graphic 1
Refrigerator door
1. Remove the refrigerator handle assembly as shown in
Graphic 2. Keep all parts together.
2. Remove door handle seal screw front. Move to opposite
side of refrigerator door as shown in Graphic 5.
3. Remove the door stop. Move it to the opposite side of the
refrigerator door as shown in Graphic 3.
4. Attach the refrigerator handle to the opposite side of the
refrigerator door with the two set screws as shown in
Graphic 2.Replace handle trim as shown.
5. Tighten all screws. Set aside the door until hinges and
freezer compartment drawer are in place.
Door Handle Seal Screw Front
Cabinet Hinge Hole Plug
7