Green Hobby Daisy G Instruções de construção

Procurar online ou descarregar pdf Instruções de construção para Brinquedo Green Hobby Daisy G. Green Hobby Daisy G 6 páginas.

Imprimir página

GREEN HOBBY

Building Instructions

Technical Information:

Wingspan:

Length:

Wing Airfoil Design:

Total Area:

Flight Weight:

Electric Version: 1

Nimh Battery:

Propeller:

Before opening the glue, oil the threads on all bolts with "After-Run" oil (available from Green Hobby),

this prevents all kind of problems later! Wherever instructions suggest gluing to the epoxy fuselage, pre-

roughen up the smooth epoxy with fine sandpaper to give the glue a better "key" to adhere onto.

USEFUL TOOLS:

Needle or point nose pliers; "pin vise" modellers drill, drill bits from 2mm to 4mm, needle files, small wire

cutters, scalpel set, a little oil, epoxy glue, matchsticks for introducing epoxy into difficult to reach places,

soldering iron with electronic grade solder & flux paste, connecting plugs for nimh battery connections to

speed controller. All modelling tools are available from Green Hobby, and once purchased, will last you

for many years.

SAFETY: All electric aircraft have self start capability, this is absent in glow engined models. Because

of this both new modellers and modellers new to electric flight should always bear in mind the possibility

of the prop beginning to spin unexpectedly, if there is a nimh battery connected up. We call plugging in

the nimh "arming the plane", if your plane is armed, the transmitter should be "ON" to shout down

background interference that might switch the motor on. Ensure throttle stick is at down-throttle off.

The plane should be on a stand, so the prop is free to spin, and the motor will not burn out due to a

stalled prop. The modeller should also never stand to the side of a spinning prop - in front OK (if the

plane is stationery!), behind OK (recommended), but never to the side, a prop blade (or stone) could fly

out at high speed without warning, injuring anybody present there.

Remember: this is a REAL aircraft, it will be dangerous if not used carefully. Keep away from

bystanders. Even when being used properly, mishaps will occasionally happen, so due caution should

be exercised. Give respect to the propeller which is extremely sharp, the batteries which if shorted can

cause fire, the aircraft which needs maintenance before flights, your piloting skills which will improve but

never achieve perfection, and radio interference. In short - allow for problems and fly safely.

TAIL: Locate the two pairs of

holes in the top of the epoxy

fuselage, near the tail. The

rearward pair are tapped with a

thread to accept bolts holding the

stabiliser-elevator on later. The

forward pair of holes, not tapped

give you correct location of the

vertical stabiliser fin-rudder.

Using a Stanley knife or scalpel,

make two cuts joining the forward

pair of holes, and remove the thin

strip of epoxy, making a slot. Now

you can trial fit your fin, sanding

the slot with a fine file, or scraping

with the scalpel for best fit.

RC- Electric Aircraft

Motor or Glider Version

1480 mm

850 mm

S 7055

24.1 dm

450 g Glider

800 g Electric

AeroNaut Race 400 6.0V Motor

AeroNaut Race 480 7.2V Black Power

Mega Motor Brushless

8 cells choice of three -

Folding 6x3" Glass + Integral Middlepiece

6x3" Carbon + Integral Middlepiece

Or.... brushless option 7 x 4.5 blades + 3.2mm integral spinner

Assembly Notes for "DAISY"

Part No. Daisy G/E/Q

"DAISY"

Mega 16.15.4 or Mega 400.12.

Part Nos KAN1050/GP1100/GP2000

Part No 7000/42

Part No 7000/48

Part No 7235/05

Part No 7236/05