CeoTronics CT-DECT Base Manual de Instruções - Página 9

Procurar online ou descarregar pdf Manual de Instruções para Auscultadores CeoTronics CT-DECT Base. CeoTronics CT-DECT Base 14 páginas. Headset for wireless duplex communication
Também para CeoTronics CT-DECT Base: Manual de Instruções (20 páginas), Manual de Instruções (20 páginas), Manual de Instruções (14 páginas), Manual de Instruções (20 páginas)

Imprimir página
4.4

Connection setup and release

è NOTE
è
The base headset and the standard headset can also be used in conjunction with other
CeoTronics DECT units. The connection setup and release for the units is carried out basically
as described in sections 4.4.1, 4.4.2. Going to do so, first ascertain which of the DECT units is
the base unit (lettering »CT-DECT Base«) and which a standard unit (lettering »CT-DECT
Standard«). For the connection setup and release at a DECT unit always the push-button » ) ) «
is used.
Please take heed of the special CeoTronics operating instructions for the DECT unit.

4.4.1 Connection setup and release by the standard headset

(1)
Prerequisites
Ÿ Headsets subscribed (sections 3...3.2.2)
Ÿ Headsets switched on and synchronized (section 4.3)
(2)
Two-party conference
Connection setup: Briefly press the push-button » ) « on the left-hand side of the headset muff of
your standard headset. When the connection is set up a high beep tone sounds in the calling standard
headset and in the called base headset. Subsequently duplex communication (speech and
simultaneous listening) is possible for both parties.
The microphone must be switched on in order to speak (see section 2.5). When the connection is active
a sidetone is audible in the headset while speaking. This is for the purpose of control.
Connection release: Briefly press the push-button » ) « on the left-hand side of the headset muff of
your standard headset. The standard headset is disconnected from the base headset. To conclude a
high beep tone then sounds in the standard headset and in the base headset. The standard headset
and base headset are now on standby.
(3)
Three-party conference
Below the designations standard headset 1 and standard headset 2 are used only for the purpose of
better differentiation in the operating instructions. Both the standard headsets operate with equal
entitlement.
Connection setup: Briefly press the push-button » ) « on the left-hand headset muff of your standard
headset 1. Standard headset 1 sets up a connection with the active base headset. Upon setup of the
connection a high beep tone sounds in standard headset 1 and in the called base headset.
The base headset does not automatically set up a connection with standard headset 2. Not until the
push-button » ) « has been pressed on standard headset 2 does standard headset 2 set up a
connection with the base headset. If a connection exists between standard headset 1 and the base
headset, the base headset then switches over automatically to three-party conference mode.
If a connection already exists between standard headset 2 and the base headset when standard
headset 1 sets up a connection with the base headset, the connection between standard headset 2 and
the base headset is retained and the base headset switches over automatically to three-party
conference mode.
The microphone must be switched on in order to speak (see section 2.5). When the connection is active
a sidetone is audible in the headset while speaking. This is for the purpose of control.
Connection release: Briefly press the push-button » ) « on the left-hand headset muff of your
standard headset 1. The standard headset 1 disconnects itself from the base headset. This procedure
is acknowledged by a high beep tone in standard headset 1 and in the base headset. If a connection
still exists at this time between the base headset and standard headset 2, the connection between the
base headset and standard headset 2 is retained. Not until the push-button » ) « on standard headset
2 is pressed briefly does standard headset 2 disconnect itself from the base headset and the three
headsets are on standby.
9