IKEA IHW7243VS0 Manual de utilização e cuidados - Página 5
Procurar online ou descarregar pdf Manual de utilização e cuidados para Campânula de ventilação IKEA IHW7243VS0. IKEA IHW7243VS0 32 páginas. 24" (61.0 cm) - 30" (76.2 cm) wall-mount canopy range hood
Imprimir página
INSTALLATION REQUIREMENTS
•
2-6x70mmscrews
_9_,_ ;;:_, C_ (} _[_
•
2 - 10 mm wall plugs
Gather the required tools and parts before starting installation.
•
4 washers
Read and follow the instructions
provided with any tools listed
here.
•
2 screwdriver
bits for TORX®t screws
Tools needed
•
Level
•
Drill with 11¼"(3.0 cm), 3/8"(9.5 mm), 7/64"(2.75 mm) and
V8" (3.0 mm) drill bits
•
Pencil
•
Wire stripper or utility knife
•
Tape measure or ruler
•
Pliers
•
Caulking gun and weatherproof
caulking compound
•
Vent clamps
•
Jigsaw or keyhole saw
•
Flat-blade screwdriver
•
Metal snips
•
Phillips screwdriver
Parts needed
•
Home power supply cable
•
Two _/2" (12.7 mm) UL listed or CSA approved strain reliefs
•
3 UL listed wire connectors
For vented installations,
you will also need:
•
1 wall or roof cap
•
Metal vent system
For non-vented
(recirculating)
installations,
you will also
need:
•
Charcoal Filter Kit Part Number 4396848 for non-vented
(recirculating)
installations only. See "Assistance
or Service"
section to order.
IMPORTANT: Observe all governing codes and ordinances.
Have a qualified technician install the range hood. It is the
installer's responsibility
to comply with installation clearances
specified on the model/serial rating plate. The model/serial
rating
plate is located behind the left filter on the rear wall of the vent
hood.
Range hood location should be away from strong draft areas,
such as windows, doors and strong heating vents.
Cabinet opening dimensions that are shown must be used. Given
dimensions
provide minimum clearance.
Grounded electrical outlet is required. See "Electrical
Requirements"
section.
The range hood is factory set for venting through the roof or wall.
For non-vented (recirculating)
Installation see "Non-vented
(recirculating) Installations"
in "Prepare Location" section.
Charcoal Filter Kit Part Number 4396848 is available from your
dealer or an authorized parts distributor.
All openings in ceiling and wall where range hood will be installed
must be sealed.
For Mobile Home Installations
The installation of this range hood must conform to the
Manufactured
Home Construction
Safety Standards, Title 24
CFR, Part 328 (formerly the Federal Standard for Mobile Home
Construction
and Safety, Title 24, HUD, Part 280) or when such
standard is not applicable, the standard for Manufactured
Home
Installation 1982 (Manufactured
Home Sites, Communities
and
Setups) ANSI A225.1/NFPA 501A*, or latest edition, or with local
codes.
Product Dimensions
Parts supplied
Remove parts from packages. Check that all parts are included.
•
Hood canopy assembly with ventilator, light bulb and grease
filter installed
•
Front panel
•
Deflector for non-vented
(recirculating) installations
•
Transition with back draft dampers installed
•
Literature package
•
2 mounting hooks with leveling screws
•
Vent cover support bracket (3 pieces, to assemble)
•
Mounting template
•
2-piece vent cover
•
4-4x8mmscrews
•
10 - 3.5 x 9.5 mm screws
•
6-5x35mmscrews
11.2"
(28.4 cm)
L
24" (61.0 crn) - 30" (76.2 cm)
t
31.9" (81 crn) rain
35.4
cm) rain
(non-vented
recircuiating
installation)
46.5" (118 crn)
T
/
ma}
I
16.7"
(42.4 cm)
!
t
14.2"
(36.0
crn)
) !
10.7"
(27.3 crn)
IIII111#1t
lllllllll
3.1"
(8.0crn)
3.9"
(10.0cm)
•
2 - 2.9 x 9.5 mm screws
1-®TORX is a registered trademark
of Acument
Intellectual
Properties, LLC.