IKEA W10177447B Instruções de instalação e manual de utilização e cuidados - Página 5

Procurar online ou descarregar pdf Instruções de instalação e manual de utilização e cuidados para Campânula de ventilação IKEA W10177447B. IKEA W10177447B 32 páginas. 24" (61.0 cm)-30" (76.2 cm) wall-mount canopy range hood

Imprimir página

Tools and Parts

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

Tools needed

Level

Drill with 1¼" (3.0 cm), ³⁄₈" (9.5 mm), ⁷⁄₆₄" (2.75 mm) and

¹⁄₈" (3.0 mm) drill bits

Pencil

Wire stripper or utility knife

Tape measure or ruler

Pliers

Caulking gun and weatherproof caulking compound

Vent clamps

Jigsaw or keyhole saw

Flat-blade screwdriver

Metal snips

Phillips screwdriver

Parts needed

Home power supply cable

Two ½" (12.7 mm) UL listed or CSA approved strain reliefs

3 UL listed wire connectors

For vented installations, you will also need:

1 wall or roof cap

Metal vent system

For non-vented (recirculating) installations, you will also

need:

Charcoal Filter Kit Part Number 4396848 for non-vented

(recirculating) installations only. See "Assistance or Service"

section to order.

Parts supplied

Remove parts from packages. Check that all parts are included.

Hood canopy assembly with ventilator, light bulb and grease

filter installed

Front panel

Deflector for non-vented (recirculating) installations

Transition with back draft dampers installed

Literature package

2 mounting hooks with leveling screws

Vent cover support bracket (3 pieces, to assemble)

Mounting template

2-piece vent cover

4 - 4 x 8 mm screws

10 - 3.5 x 9.5 mm screws

6 - 5 x 35 mm screws

2 - 2.9 x 9.5 mm screws

INSTALLATION REQUIREMENTS

2 - 6 x 70 mm screws

2 - 10 mm wall plugs

4 washers

2 screwdriver bits for TORX

Location Requirements

IMPORTANT: Observe all governing codes and ordinances.

Have a qualified technician install the range hood. It is the

installer's responsibility to comply with installation clearances

specified on the model/serial rating plate. The model/serial rating

plate is located behind the left filter on the rear wall of the vent

hood.

Range hood location should be away from strong draft areas,

such as windows, doors and strong heating vents.

Cabinet opening dimensions that are shown must be used. Given

dimensions provide minimum clearance.

Grounded electrical outlet is required. See "Electrical

Requirements" section.

The range hood is factory set for venting through the roof or wall.

For non-vented (recirculating) Installation see "Non-vented

(recirculating) Installations" in "Prepare Location" section.

Charcoal Filter Kit Part Number 4396848 is available from your

dealer or an authorized parts distributor.

All openings in ceiling and wall where range hood will be installed

must be sealed.

For Mobile Home Installations

The installation of this range hood must conform to the

Manufactured Home Construction Safety Standards, Title 24

CFR, Part 328 (formerly the Federal Standard for Mobile Home

Construction and Safety, Title 24, HUD, Part 280) or when such

standard is not applicable, the standard for Manufactured Home

Installation 1982 (Manufactured Home Sites, Communities and

Setups) ANSI A225.1/NFPA 501A*, or latest edition, or with local

codes.

Product Dimensions

11.2"

(28.4 cm)

31.9" (81 cm) min

35.4" (90 cm) min

(non-vented

recirculating

installation)

46.5" (118 cm)

max

24" (61.0 cm) - 30" (76.2 cm)

†®TORX is a registered trademark of Acument Intellectual Properties, LLC.

®†

screws

10.7"

(27.3 cm)

16.7"

(42.4 cm)

3.1"

(8.0 cm)

(3.5 cm)

14.2"

(36.0 cm)

135

3.9"

(10.0 cm)

1.4"