Avantco 177CAG48MG Manual do utilizador - Página 6

Procurar online ou descarregar pdf Manual do utilizador para Equipamento comercial para alimentos Avantco 177CAG48MG. Avantco 177CAG48MG 15 páginas. Commercial countertop griddles, charbroilers & ranges

Imprimir página

User Manual

COUNTERTOP RADIANT GAS CHARBROILER

For conversion the following guidelines should be followed:

1 . Close the manual gas valve and disconnect the product from the

gas network, making sure that there is no leakage. Then remove the

pressure regulator from the gas inlet on the product to make work easier.

2 . Remove the waste drawer (1), knobs (2) from the product and then

remove the panel (3) by removing the two screws located at the bottom

of the panel with the aid of a double screwdriver and detaching the

upper panel fittings on the product.

3 . Remove the removable grilles (9), the deflectors (8) and the welded

structure set (7).For this, extreme care must be taken, as physical

injuries or serious damage can occur.

4 . To remove the distributor tube assembly, remove the

screws that secure the distributor tube assembly(4)

to the front support with the aid of a double screwdriver.

5 . Remove the injectors (5) with a 1/2" wrench.

6 . In place of the removed gas injectors (3), place the

new injectors that are included with the kit shipped

with the product. But first apply some pipe sealant

to the valve thread and then screw-in the new injectors

to the correct gas type.

7 . Once the gas injectors are changed, reassemble

your product (6).

COUNTERTOP GAS HOT PLATE

For conversion the following guidelines should be followed:

1 . Close the manual gas valve and disconnect the product

from the gas network, making sure that there is no leakage.

Then remove the pressure regulator from the gas inlet on the

product to make work easier.

2 . Remove grills (1) and burners (2).

3 . Remove the injectors (3) with a 1/2" wrench.

4 . In place of the removed gas injectors (3), place the new

injectors that are included with the kit shipped with the

product. But first apply some pipe sealant to the valve thread

and then screw-in the new injectors to the correct gas type.

5 . Once the gas injectors (3) are changed, reassemble your

product (4).

LGP Gas Installation at Low Pressure

To use the product with LPG gas at low pressure, it is necessary that the product is checked with

the injector for use of LPG gas, if it is not with the appropriate injector, the gas conversion should be

performed following the steps described in item 2.5 of this manual.

The installation of low pressure LPG gas must be carried out in a gas station distant from the

equipment used.

A first stage (first) regulating valve with an inlet of 7 kgf/cm2 and an outlet pressure of 1.2 kgf/cm2

is installed on site, placing copper or carbon steel piping as a gas conductor to the equipment

seamless. Install at the end, next to the equipment a second 2° (second) stage valve with inlet

pressure of 1.2 kgf /cm2 and outlet pressure of 2.8 kPa or 280mmc.a.H2O.

Using a certified hose, connect the valve directly to the pressure regulator at the gas inlet at the rear

of the product, securing both ends with clamps to both the 2nd stage valve and the equipment.

Note: If in doubt consult the legislation in force in your state/ municipality.

Gas Leak Check

Before lighting the equipment and putting it into operation, check all gaskets on the gas supply line

for leaks. For this, do not use any type of wrench to check for leaks, use a sudsy soap and water

solution.

Follow the steps below for the correct procedure to power on:

1 . Turn pilot valves to OFF position by turning adjusting screws clockwise.

2 . Turn on the manual gas valve on the inlet side of the gas supply line.

3 . Check for gas leaks at the flexible coupling or gas connector connection using a soap solution.

4 . In moderation, spray or scrub the solution with soap on gas connections - active bubbling indicates the

5 . If a gas leak is detected, turn off the manual gas valve at the inlet side of the gas line. Call your certified

6 . If the equipment has no gas leak, continue with the equipment operating instruction.

www.AvantcoEquipment.com

IMPORTANT

Keep cylinders always upright (standing) and never horizontal (lying down).

location of the gas leak.

and licensed service technician.

User Manual