IKEA IUD8000WQ0 Manual de utilização e cuidados - Página 10
Procurar online ou descarregar pdf Manual de utilização e cuidados para Máquina de lavar loiça IKEA IUD8000WQ0. IKEA IUD8000WQ0 40 páginas.
Imprimir página
IMPORTANT:
Your dishwasher isdesigned tousealiquid rinse
aid. T he use ofrinse aids greatly i mproves drying byallowing
water todrain from thedishes a fter t hefinal r inse. They alsokeep
water from forming d roplets thatcandryasspots orstreaks. Do
notuse asolid orbar-type rinse aid.
Filling the dispenser
The rinse aid dispenser holds 5 oz (150 mL) of rinse aid. Under
normal conditions,
this will last for about 1 to 3 months.
1. Make sure the dishwasher
door is fully open.
2. Turn the dispenser knob to "Open" and lift it out.
f¸use R,NsE
A,0 FOR
\
0
.................................................
I
/
Openc::::_ _,!J.... II
))i
A. Dispenser knob
B. Indicator
C. Indicator
window
B
C
3=
Pour rinse aid into the opening until the indicator points to
"Full." Do not overfill. (When the rinse aid indicator drops to
the "Add" level, add more rinse aid.)
Full
Add
4. Clean up any spilled rinse aid with a damp cloth.
5. Place the knob back into the opening and turn to the "Lock"
position.
Rinse aid setting
The amount of rinse aid released into the final rinse can be
adjusted. For most water conditions, the factory setting of 2 will
give good results. If you have hard water or notice rings or
calcium spots on your glasses or dishes, try a higher setting.
Lock
Open
To adjust
the setting
1. Remove the dispenser knob.
2. Turn the arrow adjuster inside the dispenser to the desired
setting by either using your fingers or inserting a flat-blade
screwdriver into the center of the arrow and turning.
3. Replace the dispenser knob.
Hot water dissolves and activates the dishwashing detergent.
Hot water also dissolves grease on dishes and helps glasses dry
spot-free. For best dishwashing
results, water should be 120°F
(49°C) as it enters the dishwasher. Loads may not wash as well if
the water temperature
is too low. Water that is too hot can make
some soils harder to remove and cause certain detergent
ingredients not to function. If your water heater is located far from
the dishwasher, it may be necessary to run the hot water at the
faucet closest to the dishwasher to minimize the amount of cold
water in the water line. The benefits of minimizing the amount of
cold water in the water line cannot be achieved if the Delay Wash
option is chosen.
To check water temperature
1=
2.
Run hot water at the faucet closest to your dishwasher for at
least 1 minute.
Place a candy or meat thermometer
in a glass measuring
cup.
3. Check the temperature
on the thermometer
as the water is
running into the cup.
Additional efficiency tips
•
To save water and energy and time, do not rinse dishes
before putting them into the dishwasher.
•
Use a low energy, quick, or short cycle whenever possible.
These cycles use less hot water and energy than a normal
cycle.
•
Use a delay feature (on some models) to run your dishwasher
during oft-peak hours. Local utilities recommend
avoiding
heavy usage of energy at certain times of day.
•
During the summer, run your dishwasher at night. This
reduces daytime heat buildup in the kitchen.
•
Use the energy-saving
dry option whenever possible. Allow
longer drying times (overnight) when using these options. Use
a rinse aid to improve drying.
•
Use cycles or options that add extra heat to the wash or rinse
portion of the cycle only when needed.
•
Run your dishwasher with full loads. Run a rinse cycle after
meals until the dishwasher is full.
If your home is equipped with a water softener, you may want
to avoid starting the dishwasher during the regeneration of
the softener, since this may contribute to poor wash
performance.
10